ASSEMBLY INSTRUCTIONS
UPHOLSTERED PLATFORM BED
Description: Padded Backrest King Size Bed
Thank you for purchasing this quality product. Be sure to check all packing material carefully for small parts that may have come loose inside the carton during shipment.
Important Notices
If parts are missing or damaged, we will gladly ship your replacements parts free of charge.
Do not fully tighten bolts/nuts until product is fully assembled. Keep all hardware out of reach of children.
NOTICE
- Always use proper tools.
- Follow the assembly steps in order. Do not skip any steps.
- Periodically check to ensure that all connectors (bolts, screws, etc.) are tight.
- Keep the instructions for future reference.
- Check to ensure all "PARTS" and "HARDWARE" quantities, as noted, are enclosed prior to commencement of assembly.
- Place all furniture parts on a clean and flat soft surface to prevent any scratches.
- Where assembly instructions state that the assembly requires two or more people, do not attempt by yourself as there is a risk of injury.
- If you need any assistance with your new item or if you are missing any parts, please email your inquiries. We will be happy to assist and walk you through your assembly process.
- Since the dimensions of our products are manually measured, there may be an error of ± 0.79 inch between the real product and the measurement data. The measurement data is for reference only.
MADE IN CHINA
Parts List
| NO. | Description | Sketch Description | Quantity |
|---|---|---|---|
| 1 | Headboard-Left | [Component resembling a left half of a bed headboard] | 1PCS |
| 2 | Headboard-Right | [Component resembling a right half of a bed headboard] | 1PCS |
| 3 | Side Rail-Left | [Long side panel for the left side of the bed] | 1PCS |
| 4 | Side Rail-Right | [Long side panel for the right side of the bed] | 1PCS |
| 5 | Footboard | [Panel for the foot of the bed] | 1PCS |
| 6 | Soft cushion | [Padded cushion for the headboard] | 1PCS |
| 7 | Slat | [Wooden or metal slat for bed support] | 24PCS |
| 8 | Support rails-1 | [Short support beam] | 2PCS |
| 9 | Support rails-2 | [Medium length support beam] | 2PCS |
| 10 | Support rails-3 | [Long central support beam] | 1PCS |
| 11 | Support rails-4 | [Short support beam] | 2PCS |
Hardware List
| NO. | Description | Sketch Description | Quantity |
|---|---|---|---|
| A | Support Rails Connector | [Connector bracket for joining rails] | 4PCS |
| B | Slat Holder | [Clip to hold slats in place] | 48PCS |
| C | Trapezoid-Angle Iron | [Metal plate shaped like a trapezoid with right angles] | 4PCS |
| D | Long-Angle Iron | [Long L-shaped metal bracket] | 1PCS |
| E | Short-Angle Iron | [Short L-shaped metal bracket] | 4PCS |
| F | Cylindrical Leg | [Threaded metal leg] | 10PCS |
| G | Slat Support Leg | [Adjustable foot for central support] | 8PCS |
| H | Flat Washer | [Circular metal washer] | 12PCS |
| I | M8×30mm | [Bolt with M8 thread and 30mm length] | 34 PCS |
| J | M8×40mm | [Bolt with M8 thread and 40mm length] | 8 PCS |
| K | M6×30mm | [Bolt with M6 thread and 30mm length] | 20PCS |
Assembly Steps
Step 1
Connect Support rails-1 (8) with Support rails-4 (11) using Bolt (K) and Support Rails Connector (A).
Diagram Description: Shows two support rails (8) being attached to two support rails (11) using connectors (A) and bolts (K). A detail view shows a connector (A) with two bolts (K) securing it to a rail. Another detail view indicates placement of support rails (8) as 'SHORT' and 'LONG' relative to a side rail component (4).
Step 2
Use Bolt (K) to connect Support rails-2 (9) and Support rails-3 (10) to Support rails-4 (11). Do not tighten the bolts connecting Support rails-3 (10) to Support rails-4 (11) for later installation.
Diagram Description: Shows support rails (9) and (10) being attached to support rails (11) using bolts (K). A detail view shows bolts (K) and washers (H) being used. The diagram illustrates the connection points and the quantity of hardware required (K x12, H x12).
Step 3
Install Slat Holder (B) on both ends of Slat (7). Then fix the Slat Holder (B) in the holes of Support rails-1 (8) and Support rails-3 (10). It is recommended to use a hammer or other tools to knock it tight.
Diagram Description: Shows slats (7) with slat holders (B) attached to their ends. These are then inserted into the designated holes on support rails (8) and (10). A detail view shows a slat holder (B) being pressed into a hole, with a quantity of 'B x 48' indicated.
Step 4
Tighten the bolts connecting Support rails-3 (10) and Support rails-4 (11).
Diagram Description: Shows the bed frame structure with the previously installed components. A close-up view highlights the connection points between support rails (10) and (4) that need to be tightened.
Step 5
Use Bolt (J) to install Slat Support Leg (G) on Support rails-2 (9) and Support rails-3 (10).
Diagram Description: Shows the underside of the bed frame. Slat Support Legs (G) are being attached to the inner sides of support rails (9) and (10) using bolts (J). A detail view shows the bolt (J) and leg (G) connection, with a quantity of 'J x8' and 'G x8' indicated.
Step 6
Fix the iron connecting buckle on the inner side of the two Headboards together.
Diagram Description: Shows the two headboard components (1 and 2) being joined together using internal connecting brackets or buckles.
Step 7
Connect the lock buckles at the bottom of the two Headboards so that they are connected. Screw the cylindrical leg (F) onto the pedal (5), left rail (3), left rail (4), left headboard (1), and right headboard (2).
Diagram Description: Shows the headboards being secured together. Cylindrical legs (F) are shown being screwed into the footboard (5), side rails (3 and 4), and headboards (1 and 2). A detail view shows a leg (F) being screwed in, with a quantity of 'F x 10' indicated.
Step 8
Stick the soft cushion (6) on Headboard-Left (1) and Headboard-Right (2).
Note: Due to the compression packaging of the backrest, please pat it gently until it is fluffy and leave it for 48 hours to recover.
Diagram Description: Shows the soft cushion (6) being attached to the front of the headboard components (1 and 2). A note explains how to handle the compressed cushion.
Step 9
The Soft Cushion Cover can be removed. Place the cushion cover over the headboard and complete the installation of the headboard.
Diagram Description: Shows the soft cushion cover being placed over the padded headboard structure.
Step 10
Use Bolt (I) and Triangle-Angle Iron (C) and Short-Angle Iron (D) to connect Headboard-Left (1) to Side Rail-Left (3), connect Headboard-Right (2) to Side Rail-Right (4) to make Side Rail (3/4) symmetrical, then connect (3) and (4) to (5) respectively.
Diagram Description: Shows the headboard components (1 and 2) being attached to the side rails (3 and 4) using angle irons (C, D) and bolts (I). The side rails (3 and 4) are then attached to the footboard (5). Detail views show the specific hardware and connections, with quantities like 'C x4', 'E x4', 'I x32'.
Step 11
Attach Long Angle Iron (D) to the connection points between the headboard and side rails using Bolt (I).
Diagram Description: Shows the final attachment of the long angle iron (D) to reinforce the connection between the headboard and side rails, secured by bolts (I). Detail views show 'D x1' and 'I x2' for this step.
Place the previously installed bed slat rack on the bed. Note: Adjust the Slat Support Legs (G) to a suitable height.
Diagram Description: Shows the assembled slat system being placed into the bed frame. It also indicates that the Slat Support Legs (G) should be adjusted for proper height and stability.
Tips
The soft package appears in a white yellow color, which is normal. Please do not think there is a problem. This is a mixture of cotton and crushed sponge, aimed at improving resilience and providing a more comfortable feel.
