Before Starting
Please read the page carefully to identify the hardware and components included in the box. You can find the complete list on this page. During unpacking, please find a carpeted or padded area to place the unpacked hardware and components to prevent damage. Please follow the assembly instructions step by step as improper assembly may cause personal or property damage.
[!] Note: Do not assemble using power tools. This can cause the bolts to be overtightened.
[two people icon] Use 2 People
Cleaning and Care
- Please clean surfaces with a dry soft cloth. Make sure the surface is dry before assembly. If necessary, spot clean with a damp cloth or sponge; gently remove excess water; air dry. If there are spills, remove spills immediately with a clean colorfast towel or sponge.
- Please do not use abrasive cleaners as the cleaners may damage the hardware surfaces and the finishes.
- Please keep the fabric out of direct sunlight to prevent fading.
- Vacuum crevices for debris.
1 Assembled View
Diagram description: A visual representation of the fully assembled Queen-sized Dove Tufted Upholstered Bed, showing the headboard, footboard, side rails, and bed slats in place.
2 Parts List
Box A:
| Identifier | Part Name | Quantity | Description |
|---|---|---|---|
| A | Headboard | x 1 | The main upholstered headboard panel. |
| B | Headboard Leg (Left) | x 1 | The left leg component for attaching to the headboard. |
| C | Headboard Leg (Right) | x 1 | The right leg component for attaching to the headboard. |
| D | Footboard | x 1 | The footboard frame. |
| E | Side Rail | x 2 | The side frame pieces of the bed. |
| F | Side Rail Leg | x 2 | Support legs for the side rails. |
| G | Center Rail | x 2 | Central support rail(s) for the bed frame. |
| H | Center Leg | x 4 | Support legs for the center rail(s). |
| I | Bed Leg | x 2 | Legs for the footboard. |
| J | Bed Slats | x 2 | Slats to support the mattress. |
3 Hardware List
| Identifier | Hardware Name | Quantity | Description |
|---|---|---|---|
| 1 | M4 Allen Key | x 1 | Allen key for M4 bolts. |
| 2 | M5 Allen Key | x 1 | Allen key for M5 bolts. |
| 3 | Wood Screw (M4 x 25mm) | x 16 | Screws for attaching bed slats. |
| 4 | M6 x 25mm JCB | x 8 | Connector bolt (JCB) of length 25mm. |
| 5 | M6 x 45mm JCB | x 14 | Connector bolt (JCB) of length 45mm. |
| 6 | M6 Spring Washer | x 6 | Washer for M6 bolts. |
| 7 | M6 Flat Washer | x 6 | Washer for M6 bolts. |
Special Pack (SP): Contains hardware 3, 4, 5, 6, 7 (x1 of each type, implying a set).
Assembly Steps
Step 4: Assemble the Side Rail Leg (F) to the Side Rail (E).
Diagram description: Two Side Rails (E) are shown. For each Side Rail (E), a Side Rail Leg (F) is attached to the underside near one end. This is done using hardware [1] [M4 Allen Key] and [4] [M6 x 25mm JCB].
Step 5: Attached the Center Leg (H) and Bed Slats (J) to the Center Rail (G).
Diagram description: Two Center Rails (G) are shown. Four Center Legs (H) are attached to the underside of the Center Rails (G). Bed Slats (J) are then placed on top of the Center Rails (G). Assembly uses hardware [1] [M4 Allen Key] and [5] [M6 x 45mm JCB].
Step 6: Attach the Headboard Leg (Left) (B) and Headboard Leg (Right) (C) to the Headboard (A).
Diagram description: The Headboard (A) is shown. The Headboard Legs (B) and (C) are attached to the sides of the Headboard (A) frame. This step uses hardware [1] [M4 Allen Key], [5] [M6 x 45mm JCB], [6] [M6 Spring Washer], and [7] [M6 Flat Washer].
Step 7: Attach the Bed Leg (I) to the Footboard (D).
Diagram description: The Footboard (D) is shown. Two Bed Legs (I) are attached to the underside of the Footboard (D) frame.
Step 8: Assemble the Side Rail (E) to the Headboard (A) & Footboard (D).
Diagram description: The assembled Headboard (A) and Footboard (D) are shown. The Side Rails (E) are connected to the sides of the Headboard (A) and Footboard (D) frame. This step uses hardware [2] [M5 Allen Key].
Step 9: Screw the Bed Slats (J) to Side Rail (E).
Diagram description: The bed frame is now mostly assembled. The Bed Slats (J) are positioned across the Side Rails (E) and Center Rails (G). Each slat is secured to the Side Rails (E) using Wood Screws [3] [M4 x 25mm].
