INSTALLATION
Product Manual
Important Information!
Please read the entire manual before starting to assemble and/or using this product. Follow the manual thoroughly and keep it for further reference.
Avoid Scratches!
In order to avoid scratching, this furniture should be assembled on a soft layer, such as a rug.
Improve Efficiency!
Try to find a partner to install with you, which can speed up the installation efficiency and shorten the time.
Anti-Tipple Warning!
Overturned furniture can cause serious or fatal crush injuries. To prevent tipping over, be sure to use the wall attachment, if not included with this product. Please purchase the wall attachment that fits your wall. If unsure, seek professional advice. Please read and follow each step of the instructions carefully.
Important!
It is important that any product assembled using screws is re-tightened 2 weeks after assembly, and once every 3 months, to assure stability throughout the lifespan of the product. For regular maintenance and cleaning of the frame, use a rag dipped in neutral detergent, wipe it, and then dry with a clean rag. For glass materials, wipe with a rag dampened with glass cleaner, and then dry with a dry rag. Do not use an electric screwdriver, and do not use too much force when installing, as the board is easy to break.
Tools and Parts Required
Tools:
[Screwdriver icon] [Allen wrench icon]
Hardware:
- A x 6 (M8 x 40 mm)
- B x 4 (M8 x 25 mm)
- C x 2 (M8 x 20 mm)
- D x 4 (M6 x 70 mm)
- E x 20 (M6 x 35 mm)
- F x 12 (M6 x 30 mm)
- G x 32 (M6)
- H x 6 (M8)
- I x 4 (M4)
- J x 20 (M4 x 30 mm)
- K x 4 (M4 x 16 mm)
- L x 1 (M4)
- M x 1 (M5)
Parts Identification
- Part 1: Long horizontal panel x1
- Part 2: Long horizontal panel x1
- Part 3: Long horizontal panel x1
- Part 4: Long horizontal panel x1
- Part 5-L: Left side rail x1
- Part 5-R: Right side rail x1
- Part 6: Side rail/support x1
- Part 7: Support beam x1
- Part 8: Side rail/support x1
- Part 9: Support beam x1
- Part 10: Support connector x2
- Part 11: Side rail x1
- Part 12: Angled support leg x2
- Part 13: Slats (set of 5) x2
- Part 14: Slats support rail x2
- Part 15: Vertical support post x4
Assembly Warning:
Warning: Children have died from furniture tipover. To reduce the risk of furniture tipover:
- Always install the anti-tip device provided.
- Never put a TV on this product.
- Never allow children to stand, climb, or hang on drawers, doors, or shelves.
- Never open more than one drawer at a time.
- Place heaviest items in the lowest drawers.
This is a permanent label. Do not remove!
Assembly requires 2 adults.
Assembly Steps
Step 1
Hardware Used:
E x 20 (M6 x 35 mm), G x 20 (M6), L x 1 (M4)
Parts Used:
Parts 1, 2, 3, 4 (horizontal slats), Part 5-L (Left Side Rail), Part 5-R (Right Side Rail)
Description:
Lay out parts 1, 2, 3, and 4 horizontally. Attach the left side rail (5-L) to the left ends of parts 1, 2, 3, and 4 using screws (E) and washers (G). Repeat for the right side rail (5-R) on the right ends. A close-up shows screw (E) passing through the side rail and into the end of a horizontal slat, secured with washer (G).
Step 2
Hardware Used:
C x 2 (M8 x 20 mm), K x 4 (M4 x 16 mm), M x 1 (M5)
Parts Used:
Part 11 (Side Rail), Part 12 (Angled Support Leg)
Description:
Take part 11 (a side rail). Attach two support legs (part 12) to one end of part 11 using screws (C) and (K). A close-up shows screws (C) and (K) inserted into pre-drilled holes, with screw (M) also used for securing. The legs are angled.
Step 3
Hardware Used:
F x 12 (M6 x 30 mm), G x 12 (M6), L x 1 (M4)
Parts Used:
Parts 6, 8 (side rails/supports), Parts 7, 9 (support beams), Part 10 (connector)
Description:
Attach support beams (7 and 9) to the inner sides of side rails (6 and 8) using screws (F) and washers (G). Attach connector pieces (10) to the ends of support beams (7 and 9) using screws (F) and washers (G).
Step 4
Hardware Used:
B x 4 (M8 x 25 mm), M x 1 (M5)
Parts Used:
Part 11 (Side Rail), Parts 7, 9 (Support Beams)
Description:
Attach the side rail (part 11) to the frame. The diagram shows part 11 being connected to the support beams (7 and 9) using screws (B). A close-up shows screws (B) and (M) being used. A note indicates "Do not fully tighten screws." The diagram shows a 50% and 100% tightening indicator.
Step 5
Hardware Used:
A x 6 (M8 x 40 mm), H x 6 (M8), M x 1 (M5)
Parts Used:
Part 7 (Support Beam), Part 5-L (Left Side Rail), Part 5-R (Right Side Rail), Part 9 (Support Beam)
Description:
Attach the headboard assembly (formed by parts 1-4 and 5-L/5-R from Step 1) to the main frame. The diagram shows the headboard structure (represented by 5-R and 7) being attached to the side rails (5-L and 9) using screws (A) and (H). A close-up shows screws (A) and (H) inserted into holes, secured with screw (M).
Step 6
Hardware Used:
D x 4 (M6 x 70 mm), I x 4 (M4), L x 1 (M4)
Parts Used:
Parts 13 (Slats), Parts 14 (Slats Support Rail), Part 15 (Vertical Support Post)
Description:
Attach the slats support rails (14) to the vertical support posts (15) using screws (D) and (I). The diagram shows two sets of slats (13) being prepared, each with support rails (14) attached to vertical posts (15).
Step 7
Hardware Used:
J x 20 (M4 x 30 mm)
Parts Used:
Parts 13 (Slats), Parts 7, 9 (Support Beams)
Description:
Place the assembled slat sets (13) onto the main bed frame, resting on the support beams (7 and 9). Secure each slat to the support beams using screws (J). The diagram shows the slats being placed and screwed into position.
Step 8
Description:
The final assembled bed frame is shown. All parts are connected, and the structure is complete.
WARRANTY
WARRANTY CLAIMS
- There is a 30-day warranty for broken furniture or any other problems that do not work properly. The warranty will start from the date of purchase which must be verified by proof of purchase.
- Before making a claim, contact customer service. Please provide your purchase order number and details of the problem for a replacement part. Service will respond within 48 hours. If a part is out of stock, a shipping date will be provided.
- The product must be used in accordance with the instructions provided.
- If the furniture needs to be returned for other reasons, it must be cleaned and dried and returned within 30 days of receipt.
Type of Warranty Claim
- Failure to follow the furniture instructions will invalidate the warranty.
- Damage during installation is not covered, but damage during transportation is.
Scope of Responsibility
- Latitude Run shall not bear any responsibility for misuse or user damage and/or loss of parts during the installation of furniture.
- After use, damage and scratches of the furniture are not covered by the warranty.
The Warranty Relates to All Bought in The US and Covers The Following Areas
- Sheet parts: 1 month from the date of purchase.
- Electrical parts: 1 month from the date of purchase.
RETURNS
CHANGED YOUR MIND AND NEED TO RETURN YOUR ITEM?
PLEASE FOLLOW THE BELOW INSTRUCTIONS:
- If you have purchased and have simply changed your mind, follow the retailer's instructions for returns.
DEFECTIVE ITEMS
- If your item is defective in any way, i.e. it doesn't work but you can't identify why, please contact customer service.
DAMAGED ITEMS
- If you receive an order with obvious shipping damage from the retailer, refuse the delivery. If the delivery has been accepted and then shipping damage is found, please follow the specific instructions advised by the retailer.
- In all circumstances, please save all packaging material and paperwork for the order. Please be aware that if you dispose of packaging material or attempt to return the merchandise without contacting the fulfillment center, you jeopardize your chances of making a claim, and you may not receive a credit for the return.
