VEVOR Desk Shelf

Product Overview

This document provides assembly instructions, safety guidelines, and product specifications for the VEVOR Desk Shelf. The desk shelf is designed to provide additional storage and organization for your workspace.

Installation video guide available at: https://youtu.be/Atl4BDi_9Ic

Disclaimer: Statements like "Save Half" or "Half Price" represent an estimate of potential savings compared to major brands and do not guarantee savings across all product categories. Please verify savings carefully when placing an order.

Safety Instructions

WARNING:

Read this material before using this product. Failure to do so may result in serious injury.

Assembly Precautions:

• Assemble only according to these instructions. Improper assembly may create hazards.
• Wear ANSI-approved safety goggles and heavy-duty work gloves during assembly.
• Keep the assembly area clean and well-lit.
• Keep bystanders out of the area during assembly.
• Do not assemble if tired or when under the influence of alcohol, drugs, or medication.
• The product capabilities apply to properly and completely assembled products only.
• Assemble on a flat, level, hard, and smooth surface capable of safely supporting the Desk Shelf.
• If possible, use power tools to make assembly easier.
• For additional information regarding the parts listed, please refer to the Assembly Diagram. Unwrap and separate all parts in a clean work area.

Use Precautions:

• Do not exceed specified weight capacities.
• Use only on a flat, level, hard, and smooth surface that can safely support a fully loaded Desk Shelf.
• Use as intended only.
• Inspect before every use; do not use if parts are loose or damaged.

SAVE THIS MANUAL

Parts List

The following parts and hardware are included for assembly:

Parts:

• Part 1: Top Shelf
• Part 2: Middle Shelf
• Part 3: Bottom Shelf
• Part 4: Back Support Bar (long)
• Part 5: Front Support Bar (long)
• Part 6: Side Frame Legs (x2)
• Part 7: Cross Braces (x2)

Hardware:

• F: Bracket/Cap F (20*25) - Quantity: 4
• G: Screw (Ø5×40mm) - Quantity: 10
• Allen Wrench (4mm) - Quantity: 1
• A: Screw (M5×50mm) - Quantity: 12
• B: Screw (M6×30mm) - Quantity: 6
• C: Screw (M6×35mm) - Quantity: 4
• D: Screw (Ø4×35mm) - Quantity: 2
• E: Screw (Ø3.5×12mm) - Quantity: 2

Assembly Steps

Step 1:

Attach one Side Frame Leg (7) to the Front Support Bar (5) using two Screws (C).

Step 2:

Attach the second Side Frame Leg (7) to the other end of the Front Support Bar (5) using two Screws (C).

Step 3:

Attach the Back Support Bar (4) to the Side Frame Legs (7). Use two Screws (A) on each side (total 4 Screws A).

Step 4:

Attach the Middle Shelf (2) to the horizontal supports of the Side Frame Legs (7). Use two Screws (G) on each side (total 4 Screws G).

Step 5:

Attach the Top Shelf (1) to the top horizontal bars of the Side Frame Legs (7). Use two Screws (E) on each side (total 2 Screws E).

Step 6:

Attach the Top Shelf (1) to the vertical supports of the Side Frame Legs (7). Use two Screws (A) on each side (total 4 Screws A).

Step 7:

Attach the Bottom Shelf (3) to the lower horizontal bars of the Side Frame Legs (7). Use two Screws (B) on each side (total 4 Screws B).

Step 8:

Attach the Bottom Shelf (3) to the frame using two Screws (G) on each side (total 4 Screws G).

Step 9:

Attach the Bottom Shelf (3) to the frame using two Screws (A) on each side (total 4 Screws A).

Step 10:

Attach the Bottom Shelf (3) to the frame using two Screws (B) on each side (total 4 Screws B).

Step 11:

Attach the Brackets/Caps (F) to the bottom of the Side Frame Legs (7). Use one Bracket/Cap (F) and one Screw (F) on each leg (total 4 Brackets/Caps F and 4 Screws F).

Step 12: Wall Mounting

Secure the assembled desk shelf to the wall using the provided Wall Mounting Hardware (D screws and implied anchors). Ensure the shelf is stable and safely attached.

Product Parameters

* Products such as specifications, appearance, and design are subject to modification without prior notice.

Manufacturer and Representative Information

Manufacturer: Shanghaimuxinmuyeyouxiangongsi
Address: Shuangchenglu 803nong11hao1602A-1609shi, baoshanqu, shanghai 200000 CN.

Imported to AUS: SIHAO PTY LTD. 1 ROKEVA STREETEASTWOOD NSW 2122 Australia

Imported to USA: Sanven Technology Ltd. Suite 250, 9166 Anaheim Place, Rancho Cucamonga, CA 91730

EU Representative: E-CrossStu GmbH, Mainzer Landstr.69, 60329 Frankfurt am Main.

UK Representative: YH CONSULTING LIMITED. C/O YH Consulting Limited Office 147, Centurion House, London Road, Staines-upon-Thames, Surrey, TW18 4AX

Support and Warranty

For technical support and e-warranty information, please visit: www.vevor.com/support

This is the original instruction. Please read all manual instructions carefully before operating. VEVOR reserves the right to interpret its user manual. The appearance of the product is subject to the product received. VEVOR will not provide further notice for technology or software updates.