FUFU&GAGA Wardrobe Assembly Instructions
Important Information & Safety
Important Information: Please read the entire manual before starting to assemble and/or using this product. Follow the manual thoroughly and keep it for further reference.
Assembly Tips:
- Avoid Scratches: To avoid scratching, this furniture should be assembled on a soft layer, like a rug.
- Improve Efficiency: Try to find a partner to install with you, which can speed up the installation efficiency and shorten the time.
Anti-Tipple Warning: Overturned furniture can cause serious or fatal crush injuries. To prevent tipping over, be sure to use the wall attachment, if not included with this product. Please purchase the wall attachment that fits your wall. If unsure, seek professional advice. Please read and follow each step of the instructions carefully.
Maintenance & Care:
It is important that any product which is assembled using any kind of screw is re-tightened 2 weeks after assembly, and once every 3 months to assure stability throughout the lifespan of the product.
For regular maintenance and cleaning, for the frame, please use a rag dipped in neutral detergent to fully wipe it, and then dry it with a clean rag. For glass materials, wipe with a rag dampened with water glass cleaner, and then dry with a dry rag.
Do not use an electric screwdriver, and do not use too much force when installing, because the board is easy to break.
Tools and Hardware
Tools Required:
- Screwdriver (Phillips head)
- Screwdriver (Flathead)
- Drill
- Allen Wrench
- Hammer (optional)
Hardware List:
When installing, please carefully confirm whether each screw corresponds to the manual. Accessories with similar shapes can be distinguished by size.
Hardware Components:
- A: Quickfit screw, Ø6x35mm (x26)
- B: Cam lock, Ø14x9mm (x26)
- C: Wooden dowel, Ø8x30mm (x12)
- D: Wooden dowel, Ø8x50mm (x4)
- E: Screw, Ø4x40mm (x5)
- F: Screw, Ø3.5x12mm (x4)
- G: Part G (x2)
- H: Screw, Ø4x12mm (x30)
- J: Hinge (x5)
- K: Screw, M4x18mm (x4)
- L: Handle (x2)
- M: Screw, Ø5x14mm (x1)
- N: Anti-tipping device (x1)
- P: Screw, Ø3x16mm (x16)
- Q: Buckle (x16)
- R: Screw, Ø4x40mm (x1)
- S: Clothing rod (x1)
Parts List:
- 1: Plate 1 (x1)
- 2: Plate 2 (x1)
- 3: Plate 3 (x1)
- 4: Plate 4 (x2)
- 5: Plate 5 (x1)
- 6: Plate 6 (x1)
- 7: Plate 7 (x1)
- 8: Plate 8 (x1)
- 9: Plate 9 (x1)
- 10: Plate 10 (x1)
- 11: Plate 11 (x2)
- 12: Plate 12 (x1)
- 13: Door Plate 13 (x1)
- 14: Door Plate 14 (x1)
Assembly Steps
[Assembled by 2 adults]
Step 1:
Insert quickfit screw (A) into plates 2 and 3 with a screwdriver. Fix part (G) to plates 2 and 3 with screw (F) as shown.
Step 2:
Connect plate 2 and 3 with plate 5. Insert cam lock (B) into plate 5 and turn clockwise to tighten as shown.
Step 3:
Slide plate 4 along available grooves as shown.
Step 4:
Insert long wooden dowel (D) into plates 2 and 3. Attach plate 6 and fix with screw (E) as shown.
Step 5:
Insert quickfit screw (A) into plate 1 with a screwdriver as shown.
Step 6:
Slide plate 4 along available grooves as shown.
Step 7:
Insert wooden dowel (C) into plates 2 and 3. Cover with plate 1. Put cam lock (B) into plates 2 and 3 and turn clockwise to tighten as shown.
Step 8:
Fix anti-tipping device (N) to plate 1 with screw (M) as shown.
Step 9:
Insert quickfit screw (A) into plate 6 with a screwdriver as shown.
Step 10:
Insert quickfit screw (A) into plates 7 and 8 with a screwdriver as shown.
Step 11:
Insert wooden dowel (C) into plate 8. Attach plates 10 and 9. Put cam lock (B) into plates 10 and 9 and turn clockwise to tighten as shown.
Step 12:
Slide plate 11 along available grooves as shown.
Step 13:
Insert wooden dowel (C) into plates 9 and 10. Cover with plate 7. Put cam lock (B) into plates 10 and 9 and turn clockwise to tighten as shown.
Step 14:
Insert quickfit screw (A) into plate 12 with a screwdriver as shown.
Step 15:
Attach plate 12 to plates 7 and 8. Put cam lock (B) into plates 7 and 8 and turn clockwise to tighten as shown.
Step 16:
Slide plate 11 along available grooves as shown.
Step 17:
Connect the two components. Put cam lock (B) into plates 7 and 8 and turn clockwise to tighten as shown. We suggest more than two people to assemble in this step.
Step 18:
Fix hinge (J) to plates 13 and 14 with screw (H) as shown. Fix handle (L) with screw (K) as shown.
Step 19:
Attach door plate 13 to plate 3; door plate 14 to plate 8 by fixing hinge with screw (H) as shown.
Step 20:
Place clothing rod (S) in.
Step 21:
Insert buckle (Q) into back slots, and fix with screw (P) as shown.
Step 22:
Install anti-tipping device as shown. This involves attaching a bracket to the wall and the furniture.
Step 23: Hinge Adjustment
More detailed hinge adjustment mode:
- Rotate out the screws connected with the cabinet counterclockwise, adjust the gap between the overall door frame and the upper and lower, and then rotate the screws clockwise after adjusting.
- Rotate the screws at the end of the hinge counterclockwise to adjust the gap between the whole door frame and the cabinet before and after the adjustment, and then rotate the screws clockwise (rotate out to the movable door frame, do not need to over-rotate out).
- Counterclockwise rotation of the screws in the middle of the hinge will offset the corresponding part of the rear door frame to the left, and clockwise rotation of the screws in the middle of the hinge will offset the corresponding part of the rear door frame to the right.
Warranty Information
Warranty Claims
There is a 30-day warranty for broken furniture or any other problems that do not work properly. The warranty will start from the date of purchase which must be verified by proof of purchase.
Before making a claim, please call FUFU&GAGA. Please leave your purchase order number, along with some details of the problem, if you want a replacement part. FUFU&GAGA will arrange within 48 hours. If there is out of stock, we will reply with a shipping date.
The product must be used in accordance with the instructions provided. For health reasons.
For other reasons, if the furniture needs to be returned, it must be cleaned and dried and operated within 30 days of receipt.
Type of Warranty Claim
Failure to follow the furniture instructions will invalidate the warranty. This does not include damage during installation, but includes damage during transportation.
Scope of Responsibility
FUFU&GAGA shall not bear any responsibility for misuse or user damage and/or loss of parts during the installation of furniture.
After using, the damage and scratches of the furniture are not covered by the warranty.
Warranty Coverage Areas:
The warranty relates to all bought in The Us and covers the following areas:
- Sheet parts: 1 month from the date of purchase.
- Electrical parts: 1 month from the date of purchase.
Returns Policy
Changed Your Mind?
If you have purchased and have simply changed your mind, follow the retailer's instructions for returns.
Defective Items
If your item is defective in any way, i.e. it doesn't work but you can't identify why, please call FUFU&GAGA in the first instance.
Damaged Items
If you receive an order with obvious shipping damage from the retailer, then we suggest the delivery is refused. If the delivery has been accepted and then shipping damage is found, please follow the specific instructions advised by the retailer.
In all circumstances, please save all packaging material and paperwork for the order. Please be aware that if you dispose of packaging material or attempt to return the merchandise without contacting the fulfiller, you jeopardise your chances of making a claim, and you may not receive a credit for the return.
