Manuals+

Wardrobe

Version: 03/15/2023

Important Information

Please read the entire manual before starting to assemble and/or using this product. Follow the manual thoroughly and keep it for further reference.

Assembly Tips

  • Avoid Scratches: To prevent scratching, this furniture should be assembled on a soft layer, such as a rug.
  • Improve Efficiency: Try to find a partner to install with you, which can speed up the installation efficiency and shorten the time.

Anti-Topple Warning

Overturned furniture can cause serious or fatal crush injuries. To prevent tipping over, be sure to use the wall attachment, if not included with this product. Please purchase the wall attachment that fits your wall. If unsure, seek professional advice. Please read and follow each step of the instructions carefully.

Important Maintenance Notes

  • It is important that any product assembled using any kind of screw is re-tightened 2 weeks after assembly, and once every 3 months, to assure stability throughout the lifespan of the product.
  • For regular maintenance and cleaning of the product frame, please use a rag dipped in neutral detergent to fully wipe it, and then dry it with a clean rag.
  • For glass materials, wipe with a rag dampened with water glass cleaner, and then dry with a dry rag.
  • Do not use an electric screwdriver, and do not use too much force when installing, because the board is easy to break.

Tools Required

Please prepare the following tools:

  • Screwdriver ?
  • Hammer ?
  • Allen Key ?

Parts and Hardware Identification

When installing, please carefully confirm whether each screw corresponds to the manual. Accessories with similar shapes can be distinguished by size.

  • A x 47: Ø 6 x 34 mm
  • B x 8: Ø 6 x 28 mm
  • C x 55: Ø 15 x 10 mm
  • D x 48: Ø 8 x 30 mm
  • E x 12: Ø 4 x 40 mm
  • F x 16: Ø 4 x 30 mm
  • G x 38: Ø 3 x 12 mm
  • H x 15: 15.5 x 10 x 1.2 mm
  • J x 15: Ø 3 x 16 mm
  • K x 4: 35 mm
  • L x 4: 35 mm
  • M x 48: Ø 4 x 16 mm
  • N x 8: 150 x 34 mm
  • P x 16: Ø 4 x 18 mm
  • Q x 8: 35 x 400 mm
  • R x 32: Ø 3 x 12 mm
  • S x 2: 53 x 24 x 12 mm
  • T x 1: 770 mm
  • U x 4: Ø 4 x 14 mm
  • V x 1: [Anti-tipping device]

Exploded View and Safety Warning

Diagram shows an exploded view of the wardrobe components, with each part numbered for reference.

WARNING: Furniture tipover can cause serious or fatal crush injuries. To reduce the risk of furniture tipover:

  • ALWAYS install the tipover restraint provided.
  • NEVER put a TV on this product.
  • NEVER allow children to stand, climb, or hang on drawers, doors, or shelves.
  • NEVER open more than one drawer at a time.
  • Place heaviest items in the lowest drawers.

This is a permanent label. Do not remove!

Slide Separation Instructions

Slides Must Be Separated Before Assembly. After Separated, Set Aside Until Needed for Assembly.

Las diapositivas deben separarse antes del montaje. Después de la separación, déjelo a un lado hasta que sea necesario.

Les glissières doivent être séparées avant l'assemblage. Après la séparation, mettez de côté jusqu'au moment de l'assemblage.

Step 1: Extend Slide

Diagram shows extending the slide.

Step 2: Push Lever UP

Diagram shows pushing the lever upwards.

Step 3: Remove Runner

Diagram shows removing the runner.

Assembly Steps

Step 1

Hardware: A x 4 (Ø 6 x 34 mm)

Insert quickfit screw(A) into corresponding holes in plate 11 with a screwdriver as shown. Diagram shows plate 11 with holes labeled 'A', and screw A being inserted. A warning icon (⚠️) is present.

Step 2

Hardware: C x 4 (Ø 15 x 10 mm), D x 4 (Ø 8 x 30 mm)

Attach plate 13 to plate 11 with wooden dowel(D) at first. Put cam lock(C) into holes in plate 13 and turn clockwise to tighten as shown. Diagram shows plates 11 and 13 being joined, with dowels D and cam locks C. Note: "The holes are facing down". A warning icon (⚠️) is present.

Step 3

Hardware: A x 4 (Ø 6 x 34 mm)

Insert quickfit screw(A) into corresponding holes in plate 10 with a screwdriver as shown. Diagram shows plate 10 with holes labeled 'A', and screw A being inserted. A warning icon (⚠️) is present.

Step 4

Hardware: C x 4 (Ø 15 x 10 mm), D x 4 (Ø 8 x 30 mm)

Attach plate 10 to plate 13 with wooden dowel(D) at first. Put cam lock(C) into holes in plate 13 and turn clockwise to tighten as shown. Diagram shows plates 10 and 13 being joined, with dowels D and cam locks C. Note: "The holes are facing down". A warning icon (⚠️) is present.

Step 5

Hardware: A x 6 (Ø 6 x 34 mm)

Insert quickfit screw(A) into corresponding holes in plate 12 with a screwdriver as shown. Please pay attention to the holes where the accessories are inserted. Diagram shows plate 12 with holes labeled 'A', and screw A being inserted. A warning icon (⚠️) is present.

Step 6

Hardware: E x 6 (Ø 4 x 40 mm), D x 6 (Ø 8 x 30 mm)

Attach plate 12 to plates 10, 11, and 9 with wooden dowel(D), then fix using screw(E) as shown. Diagram shows plates 12, 10, 11, and 9 being joined. Note: "face up" and "The holes are facing down". A warning icon (⚠️) is present.

Step 7

Hardware: E x 6 (Ø 4 x 40 mm), D x 6 (Ø 8 x 30 mm)

Attach plate 1 to plates 10, 11, and 9 with wooden dowel(D), then fix using screw(E) as shown. Diagram shows plates 1, 10, 11, and 9 being joined. Note: "face up". A warning icon (⚠️) is present.

Step 8

Hardware: A x 4 (Ø 6 x 34 mm)

Insert quickfit screw(A) into plates 2 and 3 with a screwdriver as shown. Diagram shows plates 2 and 3 with holes labeled 'A', and screw A being inserted. A warning icon (⚠️) is present.

Step 9

Hardware: C x 4 (Ø 15 x 10 mm), D x 2 (Ø 8 x 30 mm)

Attach plate 2 to plate 14 with wooden dowel(D); put cam lock(C) into holes in plate 14 and turn clockwise to tighten as shown. Attach plate 3 to plate 15 with wooden dowel(D); put cam lock(C) into holes in plate 15 and turn clockwise to tighten as shown. Diagrams show plates 2, 14 and 3, 15 being joined. Warning icons (⚠️) are present.

Step 10

Hardware: A x 4 (Ø 6 x 34 mm), Q x 4 (35 x 400 mm), R x 8 (Ø 3 x 12 mm)

Separate glide into two parts at first (refer to Page 5). Fix slide rail(Q) to plate 6 and 7 using screw(R) as shown. Insert quickfit screw(A) into plate 6 and 7 as shown. Diagrams show slide rails being attached. Warning icons (⚠️) are present.

Step 11

Hardware: A x 4 (Ø 6 x 34 mm), Q x 4 (35 x 400 mm), R x 8 (Ø 3 x 12 mm)

Fix slide rail(Q) to plate 8 using screw(R) at first. Flip the plate, and fix slide rail(Q) as shown. Insert quickfit screw(A) into plate 8 as shown. Diagram shows slide rail attachment and rotation. Warning icons (⚠️) are present.

Step 12

Hardware: C x 2 (Ø 15 x 10 mm), D x 3 (Ø 8 x 30 mm)

Attach plates 3, 15, and 5 to plate 7 with wooden dowel(D) at first. Put cam lock(C) into holes in plates 3 and 5 and turn clockwise to tighten as shown. Diagram shows plates 3, 5, and 15 being attached to plate 7. Note: "the holes are facing up". Warning icons (⚠️) are present.

Step 13

Hardware: C x 2 (Ø 15 x 10 mm), D x 3 (Ø 8 x 30 mm)

Attach plates 3, 15, and 5 to plate 8 with wooden dowel(D) at first. Put cam lock(C) into holes in plates 3 and 5 and turn clockwise to tighten as shown. Diagram shows plates 3, 5, and 15 being attached to plate 8. Warning icons (⚠️) are present.

Step 14

Hardware: C x 2 (Ø 15 x 10 mm), D x 3 (Ø 8 x 30 mm)

Attach plate 2, 14, and 4 to plate 8 with wooden dowel(D) at first. Put cam lock(C) into holes in plates 2 and 4 and turn clockwise to tighten as shown. Diagram shows plates 2, 4, and 14 being attached to plate 8. Note: "the holes are facing up". Warning icons (⚠️) are present.

Step 15

Hardware: C x 2 (Ø 15 x 10 mm), D x 3 (Ø 8 x 30 mm)

Attach plate 6 to plates 4, 2, and 14 with wooden dowel(D) at first. Put cam lock(C) into holes in plates 2 and 4 and turn clockwise to tighten as shown. Diagram shows plate 6 being attached to plates 4, 2, and 14. Warning icons (⚠️) are present.

Step 19

Hardware: C x 6 (Ø 15 x 10 mm), D x 6 (Ø 8 x 30 mm)

Connect the two components with wooden dowel(D) at first. Put cam lock(C) into holes in plates 7, 8, and 6 and turn clockwise to tighten as shown. Diagram shows two main sections being joined. Warning icons (⚠️) are present.

Step 17

Hardware: G x 38 (Ø 3 x 12 mm), H x 15 (15.5 x 10 x 1.2 mm), J x 15 (Ø 3 x 16 mm)

Fix back plates 21, 22, 23, 24, 25, and 26 using screw(G) at first. Fix each plate together using iron sheet(H) with screw(J) as shown. Diagram shows back plates being attached. Warning icons (⚠️) are present.

Step 18

Hardware: A x 5 (Ø 6 x 34 mm)

Insert quickfit screw(A) into plate 32 as shown. Diagram shows plate 32 with holes labeled 'A', and screw A being inserted. A warning icon (⚠️) is present.

Step 20

Hardware: S x 2 (53 x 24 x 12 mm), T x 1 (770 mm), U x 4 (Ø 4 x 14 mm)

Fix part(S) to plate 9 and 11 using screw(U) as shown. Place clothing rod(T) as shown. Diagram shows parts S and T being installed. Warning icons (⚠️) are present.

Step 21

Hardware: K x 4 (35 mm), M x 8 (4 x 16 mm)

Fix hinge(K) to plate 27 and 29 respectively using screw(M) as shown. Please note, hinge(K) is used in this step. Diagram shows hinge attachment. Warning icons (⚠️) are present.

Step 22

Hardware: M x 16 (4 x 16 mm), N x 2 (150 x 34 mm), P x 4 (4 x 18 mm)

Attach plate 27 to plate 9 by fixing hinge(K) with screw(M) as shown. Attach plate 29 to plate 10 by fixing hinge(K) with screw(M) as shown. Fix handle(N) to both door plates using screw(P) as shown. Diagram shows door attachment and handle installation. Warning icons (⚠️) are present.

Step 23

Hardware: L x 4 (35 mm), M x 8 (4 x 16 mm)

Fix hinge(L) to another plate 27 and 28 respectively using screw(M) as shown. Please note, hinge(L) is used in this step. Diagram shows hinge attachment. Warning icons (⚠️) are present.

Step 24

Hardware: M x 8 (4 x 16 mm), N x 1 (150 x 34 mm), P x 2 (4 x 18 mm)

Attach plate 28 to plate 11 by fixing hinge(L) with screw(M) as shown. Fix handle(N) using screw(P) as shown. Diagram shows door attachment and handle installation. Note: "the holes are facing up". Warning icons (⚠️) are present.

Step 25

Hardware: M x 8 (4 x 16 mm), N x 1 (150 x 34 mm), P x 2 (4 x 18 mm)

Attach plate 27 to plate 11 by fixing hinge(L) with screw(M) as shown. Fix handle(N) using screw(P) as shown. Diagram shows door attachment and handle installation. Warning icons (⚠️) are present.

Step 26

Hardware: Q x 8 (35 x 400 mm), R x 16 (Ø 3 x 12 mm)

Fix runner(Q) to plate 16 and 17 using screw(R) as shown. Diagram shows runner attachment. Warning icons (⚠️) are present.

Step 27

Hardware: B x 4 (Ø 6 x 28 mm)

Insert quickfit screw(B) into plate 18 as shown. Diagram shows plate 18 with holes labeled 'B', and screw B being inserted. A warning icon (⚠️) is present.

Step 28

Hardware: A x 16 (Ø 6 x 34 mm), B x 4 (Ø 6 x 28 mm)

Insert quickfit screw(A) and (B) into plates 30 and 31 as shown. Diagram shows plates 30 and 31 with holes labeled 'A' and 'B', and screws being inserted. A warning icon (⚠️) is present.

Step 29

Hardware: C x 10 (Ø 15 x 10 mm), D x 2 (Ø 8 x 30 mm)

Attach plates 16, 17, and 20 to plate 30, and turn cam lock(C) clockwise to tighten as shown. Diagram shows plates 16, 17, and 20 being attached to plate 30. Warning icons (⚠️) are present.

Step 30

Slide plate 19 along grooves as shown. Diagram shows plate 19 sliding into place.

Step 31

Hardware: C x 2 (Ø 15 x 10 mm), D x 2 (Ø 8 x 30 mm)

Attach plate 18 to plate 19 with wooden dowel(D), then turn cam lock(C) clockwise to tighten as shown. Diagram shows plate 18 being attached to plate 19. Warning icons (⚠️) are present.

Step 32

Hardware: F x 8 (Ø 4 x 30 mm)

Fix plate 18 to plates 16 and 17 with screw(F) as shown. Diagram shows plate 18 being attached to plates 16 and 17. Warning icons (⚠️) are present.

Step 33

Hardware: N x 2 (150 x 34 mm), P x 4 (4 x 18 mm)

Fix handle(N) to plate 30 using screw(P) as shown. Diagram shows handle attachment to plate 30. Warning icons (⚠️) are present.

Step 34

Hardware: C x 10 (Ø 15 x 10 mm), D x 2 (Ø 8 x 30 mm)

Attach plates 16, 17, and 20 to plate 31, and turn cam lock(C) clockwise to tighten as shown. Diagram shows plates 16, 17, and 20 being attached to plate 31. Warning icons (⚠️) are present.

Step 35

Slide plate 19 along grooves as shown. Diagram shows plate 19 sliding into place.

Step 36

Hardware: C x 2 (Ø 15 x 10 mm), D x 2 (Ø 8 x 30 mm)

Attach plate 18 to plate 19 with wooden dowel(D), then turn cam lock(C) clockwise to tighten as shown. Diagram shows plate 18 being attached to plate 19. Warning icons (⚠️) are present.

Step 37

Hardware: F x 8 (Ø 4 x 30 mm)

Fix plate 18 to plates 16 and 17 with screw(F) as shown. Diagram shows plate 18 being attached to plates 16 and 17. Warning icons (⚠️) are present.

Step 38

Hardware: N x 2 (150 x 34 mm), P x 4 (4 x 18 mm)

Fix handle(N) to plate 31 using screw(P) as shown. Diagram shows handle attachment to plate 31. Warning icons (⚠️) are present.

Step 39: Anti-Tipping Device Installation

Install anti-tipping device as shown. Note: Panel 30 is on the left, and panel 31 is on the right. Diagram shows the anti-tipping device being installed.

Step 40: Wall Mounting

Diagram shows the wardrobe being secured to a wall using appropriate hardware. Tools required for wall mounting are depicted.

Step 41: Door Alignment

Adjust hinge to make door alignment. Diagrams illustrate hinge adjustments for vertical, horizontal, and depth alignment.

Warranty

Warranty Claims

  • There is a 30-day warranty for broken furniture or any other problems that do not work properly. The warranty will start from the date of purchase, which must be verified by proof of purchase.
  • Before making a claim, please call us. Provide your purchase order number and details of the problem. Replacement parts will be arranged within 48 hours. If out of stock, a shipping date will be provided.
  • The product must be used in accordance with the instructions provided.
  • For other reasons, if the furniture needs to be returned, it must be cleaned, dried, and returned within 30 days of receipt.

Type of Warranty Claim

  • Failure to follow the furniture instructions will invalidate the warranty.
  • Damage during installation is not covered, but damage during transportation is.

Scope of Responsibility

  • FUFU&GAGA shall not bear any responsibility for misuse or user damage and/or loss of parts during the installation of furniture.
  • Damage and scratches after use are not covered by the warranty.

The Warranty Relates to All Bought in The US and Covers The Following Areas

  • Sheet parts: 1 month from the date of purchase.
  • Electrical parts: 1 month from the date of purchase.

Returns

Changed Your Mind and Need to Return Your Item?

Please Follow The Below Instructions:

  • If you have purchased and have simply changed your mind, follow the retailer's instructions for returns.

Defective Items

  • If your item is defective in any way, i.e., it doesn't work but you can't identify why, please call us in the first instance.

Damaged Items

  • If you receive an order with obvious shipping damage from the retailer, we suggest the delivery is refused.
  • If the delivery has been accepted and then shipping damage is found, please follow the specific instructions advised by the retailer.
  • In all circumstances, please save all packaging material and paperwork for the order.
  • Please be aware that if you dispose of packaging material or attempt to return the merchandise without contacting the fulfiller, you jeopardize your chances of making a claim, and you may not receive a credit for the return.

PDF preview unavailable. Download the PDF instead.

64650400 Adobe PDF library 16.03 Adobe Illustrator 26.0 (Windows)

Related Documents

Preview FUFU&GAGA Sideboard Assembly Instructions and User Guide
Comprehensive assembly guide for the FUFU&GAGA sideboard, featuring step-by-step instructions, parts list, tool requirements, and important safety information for proper installation and use.
Preview FUFU&GAGA KF020366-01 White Wood Wardrobe Armoire Assembly Instructions
Comprehensive guide for assembling the FUFU&GAGA KF020366-01 White Wood 2-Door Wardrobe Armoire with 3 Drawers. Includes parts list, step-by-step instructions, and safety information.
Preview FUFU&GAGA Display Cabinet Assembly Instructions
Comprehensive assembly guide for the FUFU&GAGA Display Cabinet, detailing tools required, parts identification, step-by-step assembly instructions, important safety warnings, warranty information, and returns policy.
Preview FUFU&GAGA KF200252-01+02 White 9-Drawer Double Dresser Assembly Instructions
Comprehensive assembly guide for the FUFU&GAGA KF200252-01+02 White 9-Drawer Double Dresser, including important safety information, parts list, and step-by-step instructions for assembly and care.
Preview FUFU&GAGA Display Cabinet Assembly Instructions and User Guide
Comprehensive assembly guide for the FUFU&GAGA Display Cabinet (Model KF210257-01/02/03), including a parts list, step-by-step visual guides, safety warnings, and warranty information. Learn how to build your cabinet efficiently and safely.
Preview FUFU&GAGA Furniture Warranty Information
This document outlines the warranty terms and conditions for FUFU&GAGA furniture products, including warranty claims, scope of responsibility, and covered areas.
Preview FUFU&GAGA Night Table Assembly Instructions and Safety Guide
Comprehensive assembly instructions, safety warnings, and maintenance tips for the FUFU&GAGA Night Table / Shoe Storage Cabinet (Model KF020233-01). Learn how to safely build and care for your furniture.
Preview Display Cabinet Assembly Instructions and Warranty Information
Comprehensive guide for assembling a FUFU&GAGA display cabinet, including detailed steps, parts list, and warranty information. Learn how to safely assemble and maintain your furniture.