Sideboard Assembly Instructions
Important Information
⚠️ Please read the entire manual before starting to assemble and/or using this product. Follow the manual thoroughly and keep it for further reference.
Avoid Scratches
To avoid scratching this furniture, it should be assembled on a soft layer, such as a rug.
Improve Efficiency
Try to find a partner to install with you, which can speed up the installation efficiency and shorten the time.
Anti-Tipple Warning
Overturned furniture can cause serious or fatal crush injuries. To prevent tipping over, be sure to use the wall attachment, if not included with this product. Please purchase the wall attachment that fits your wall. If unsure, seek professional advice. Please read and follow each step of the instructions carefully.
Important Maintenance & Assembly Tips
It is important that any product assembled using screws is re-tightened 2 weeks after assembly, and once every 3 months to ensure stability throughout the product's lifespan.
For regular maintenance and cleaning: use a rag dipped in neutral detergent to wipe the frame, then dry with a clean rag. For glass materials, wipe with a rag dampened with water glass cleaner, then dry with a dry rag.
Do not use an electric screwdriver or excessive force when installing, as the board is easy to break.
Tools Required
- Tape Measure
- Pencil
- Spirit Level
- Screwdriver ?
- Drill ?️
- Hammer ?
Hardware Included
- A x 33+1 (Ø6 x 35mm)
- B x 33+1 (Ø15 x 10mm)
- C x 64+2 (Ø3 x 10mm)
- D x 32+1 (Ø6 x 30mm)
- E x 12 (Ø5 x 40mm)
- F x 5 (Ø4 x 14mm)
- G x 15 (Ø4 x 35mm)
- H x 1 (Ø3 x 16mm)
- J x 1 (Hex Key)
- K x 6 (Hinge)
- L x 1 (Anti-tipping Device)
- M x 1 (Part M)
- T x 5 (Knob)
- Q x 2 (Part Q)
- N x 43+2 (Nail)
- P x 8 (Part P)
- CL x 3 (Slide Rail CL)
- CR x 3 (Slide Rail CR)
- DL x 3 (Runner DL)
- DR x 3 (Runner DR)
Parts List
- Part 1: 1PC
- Part 2: 1PC
- Part 3: 1PC
- Part 4: 1PC
- Part 5: 1PC
- Part 6: 1PC
- Part 7: 1PC
- Part 8: 1PC
- Part 9: 1PC
- Part 10: 1PC
- Part 11: 1PC
- Part 12: 1PC
- Part 13: 2PCS
- Part 14: 1PC
- Part 15: 1PC
- Part 16: 4PCS
- Part 17: 3PCS
- Part 18: 1PC
- Part 19: 3PCS
- Part 20: 1PC
- Part 21: 1PC
- Part 22: 1PC
- Part 23: 2PCS
- Part 24: 2PCS
- Part 25: 2PCS
- Part 26: 1PC
- Part 27: 2PCS
- Part 28: 1PC
- Part 29: 1PC
Assembly Steps
Step 1
Fix part Q to plates 4 and 3 with screw C as shown. Insert quickfit screw A into corresponding holes in plate 2 and 3 with a screwdriver.
Diagram shows part Q being attached to plates 4 and 3 using screws C. Then, screws A are inserted into plates 2 and 3.
Step 2
Attach plate 5 to plate 2 with wooden dowel D and turn cam locks B clockwise to tighten as shown.
Diagram shows plate 5 being connected to plate 2 using dowels D and cam locks B, which are turned 180° to secure.
Step 3
Attach plate 3 to plate 5 with wooden dowel D and turn cam locks B clockwise to tighten as shown.
Diagram shows plate 3 being connected to plate 5 using dowels D and cam locks B, which are turned 180° to secure.
Step 4
Insert quickfit screw A into corresponding holes in plate 1. Fix part M to plate 1 with screw H as shown. Attach plate 1 to plates 2, 3, 4 with wooden dowel D and turn cam locks B clockwise to tighten as shown.
Diagram shows screws A inserted into plate 1, part M attached to plate 1 with screw H. Then, plate 1 is attached to the assembly of plates 2, 3, 4 using dowels D and cam locks B.
Step 5
Cover plate 6 to plates 2, 3, 4 with wooden dowel D and then fix with screw E as shown.
Diagram shows plate 6 being placed on top of the assembled structure (plates 2, 3, 4) and secured with dowels D and screws E.
Step 6
Insert quickfit screw A into corresponding holes in plate 6 with a screwdriver as shown.
Diagram shows screws A being inserted into plate 6.
Step 7
Please pay attention to the holes where the accessories are inserted. Fix slide rail CL to plates 10 and 12 respectively with screw C. Fix slide rail CR to plate 11 and another side of plate 12 respectively with screw C as shown.
Diagrams show slide rails CL and CR being attached to plates 10, 11, and 12 using screws C.
Step 8
Attach two plate 13 to plate 12 with wooden dowel D and then fix with screw E as shown. Connect plate 10 and 11 to plate 13 with wooden dowel D and turn cam locks B clockwise to tighten as shown.
Diagrams show plates 13 attached to plate 12, and then plates 10 and 11 attached to plates 13 using dowels D, screws E, and cam locks B.
Step 9
Attach plates 10, 12, 11 to plate 6 with wooden dowel D and turn cam locks B clockwise to tighten as shown.
Diagram shows the assembly from Step 8 being attached to plate 6 using dowels D and cam locks B.
Step 10
Cover plate 14 to the component with wooden dowel D, then fix with screw E as shown.
Diagram shows plate 14 being placed on top of the structure and secured with dowels D and screws E.
Step 11
Fix back plates 15 and 29 with nail N as shown. Rotate leg 16 into plate 14 as shown.
Diagrams show nails N being hammered into the back panels (15, 29) and legs 16 being attached to plate 14.
Step 12
Insert part P into plates 2 and 3, and put shelf 27 in.
Diagram shows part P being inserted into holes on the side panels (2, 3) and shelf 27 being placed.
Step 13
Please do not use an electric screwdriver or use force to rotate, may cause crack. Fix hinge K to plates 8 and 9 with screw C as shown.
Diagrams show hinges K being attached to the doors (plates 8 and 9) using screws C.
Step 14
Please do not use an electric screwdriver or use force to rotate, may cause crack. Attach plate 8 to plate 2; plate 9 to plate 4 by fixing hinge with screw C as shown. Fix knob T with screw F.
Diagrams show doors (plates 8 and 9) being attached to the main body (plates 2 and 4 respectively). Knobs T are attached to the doors with screws F.
Step 15
Hinge adjustment: Follow the diagrams to adjust the doors for proper alignment and closure.
Diagrams illustrate the adjustment mechanisms of the hinges.
Step 16
Attach plates 17, 19, 22 to plate 18 with screw G as shown. Insert quickfit screw A into plate 20 with a screwdriver as shown. Fix knob T with screw F. Slide plate 21 into available slots.
Diagrams show drawer components (17, 19, 22) being attached to drawer sides (18) with screws G. Screws A are inserted into drawer fronts (20). Knobs T are attached with screws F. Drawer base (21) is slid into place.
Step 17
Attach plate 25 to the component and turn cam locks B clockwise to tighten as shown. Please pay attention to the holes where the accessories are inserted. Fix runner DL and DR to plates 19 and 17 respectively with screw C as shown.
Diagrams show drawer base/sides (25) being attached to drawer fronts/backs (19, 17) using cam locks B. Runners DL and DR are attached to the drawer sides using screws C.
Step 18
Attach plates 17, 19 to plate 23 with screw G as shown. Insert quickfit screw A into plates 25, 28 with a screwdriver as shown. Fix knob T with screw F. Slide plate 24 into available slots.
Diagrams show drawer sides (17, 19) attached to drawer fronts/backs (23) with screws G. Screws A are inserted into drawer fronts (25, 28). Knobs T are attached with screws F. Drawer bases (24) are slid into place.
Step 19
Attach plate 28 and plate 25 to the component and turn cam locks B clockwise to tighten as shown. Fix runner DL and DR to plates 19 and 17 respectively with screw C as shown.
Diagrams show drawer fronts/backs (28, 25) attached to drawer sides (19, 17) using cam locks B. Runners DL and DR are attached to the drawer sides using screws C.
Step 20
Align rails, slide all drawers.
Diagram shows the completed sideboard with drawers being inserted into their respective runners.
Step 21
Install anti-tipping device L with screw G as shown.
Diagram shows the anti-tipping device L being attached to the top rear of the furniture and secured to the wall with screw G.
Final Check and Safety
Ensure all parts are securely fastened. The anti-tipping device is crucial for safety to prevent serious injury from furniture tip-over. ⚠️
Warranty Information
Warranty Claims
There is a 30-day warranty for broken furniture or other problems that do not work properly. The warranty starts from the date of purchase, which must be verified by proof of purchase.
Before making a claim, please call FUFU&GAGA. Provide your purchase order number and details of the problem for part replacement. Replacements will be arranged within 48 hours. If parts are out of stock, a shipping date will be provided.
The product must be used in accordance with the instructions provided. For health reasons, returned furniture must be cleaned and dried, and operated within 30 days of receipt.
Type of Warranty Claim
Failure to follow the furniture instructions will invalidate the warranty. Damage during installation is not covered, but damage during transportation is.
Scope of Responsibility
FUFU&GAGA shall not bear any responsibility for misuse or user damage and/or loss of parts during the installation of furniture.
Damage and scratches after use are not covered by the warranty.
Warranty Coverage Areas
- Sheet parts: 1 month from the date of purchase.
- Electrical parts: 1 month from the date of purchase.
Returns
Changed Your Mind?
If you have purchased and simply changed your mind, follow the retailer's instructions for returns.
Defective Items
If your item is defective in any way, i.e., it doesn't work but you can't identify why, please call FUFU&GAGA in the first instance.
Damaged Items
If you receive an order with obvious shipping damage from the retailer, refuse the delivery. If delivery is accepted and shipping damage is found later, please follow the specific instructions advised by the retailer.
In all circumstances, please save all packaging material and paperwork for the order. Disposing of packaging material or attempting to return merchandise without contacting the fulfillment center may jeopardize your chances of making a claim and receiving credit for the return.
