JA-110P PET - PIR Motion Detector for Buses with Basic Pet Immunity
Introduction
This document was machine-translated from the Czech original. In case of any ambiguities or doubts, please refer to the original version of the document. If you encounter errors or have further questions, please contact technical support (contact details can be found at the end of this document).
The JA-110P PET is a bus device of the JABLOTRON system. It is used for detecting human movement indoors. Unlike standard JABLOTRON series passive infrared motion detectors, this detector has a modified detection characteristic and offers basic pet immunity. The detector eliminates the influence of small animals moving on the floor (weighing up to 25 kg and up to 40 cm in height). The detector has a pulse reaction and occupies a single position in the system. Installation of the detector must be performed by a qualified specialist with a valid certificate issued by an authorized distributor.
Installation
! Always disconnect the system power before connecting the detector to the bus.
- Open the detector cover by pressing the latch (5). Do not touch the PIR sensor (11) inside – this may lead to its damage.
- Remove the printed circuit board – it is held by a clip (3).
- Make holes for screws and cable in the plastic base. The recommended installation height for the detector is 2 m from the floor.
- Insert the bus cable and attach the plastic base to the wall using screws (vertically, so that the cover's tab points downwards).
- Insert the printed circuit board back and connect the cables to the terminals (8).
- Proceed according to the control panel installation manual.
Figure 1: Detector opening and description of internal and external parts of the product.
Part I: Main detector body.
Part II: Detector cover.
- 1 – Holes for mounting on a flat wall
- 2 – Holes for mounting at an angle (in a corner)
- 3 – Printed circuit board mounting tab
- 4 – Holes for mounting at an angle (in a corner)
- 5 – Cover latch
Internal Components and Connections:
- 6 – Red LED: trigger
- 7 – Yellow LED: fault
- 8 – Bus terminals
- 9 – Production code
- 10 – Cover opening sensor
- 11 – IR sensor (infrared sensor)
System Integration and Settings
Depending on the type of control panel, use the recommended software or application; see the control panel's user manual.
Technical Specifications
| Specification | Value | Specification | Value |
|---|---|---|---|
| Power | from control panel bus 12 V (8...15 V) | Operating environment | Indoor general |
| Quiescent current consumption | 5 mA | Operating temperature range | -10 °C to +40 °C |
| Maximum current consumption | 10 mA | Average operating humidity | 75% relative humidity, non-condensing |
| Recommended installation height | 2 m above floor | Certification body | Trezor Test sro (No. 3025), KIWA Nederland bv. |
| Detection angle/coverage | 90°/12 m | Also complies with | EN 50131-1, EN 50131-2-2, EN 50130-4, EN 55032, EN IEC 63000, T 031. |
| Detection angle/zone | 90°/7 m | Recommended screw | Ø 3.5 x 40 mm (countersunk head) |
| Pet immunity | (Implied feature) | Dimensions | 60 x 98 x 52 mm |
| Weight | 75 g | Classification | Class 2/II. indoor use (according to EN 50131-1) |
Compliance and Disposal
JABLOTRON a.s. hereby declares that the JA-110P PET device complies with the harmonized legislation of the European Union: Directives No. 2014/30/EU, 2011/65/EU when used as intended. The original declaration of conformity can be found on the website www.jablotron.com in the "Downloads" section.
Note: Proper disposal of this product helps conserve valuable resources and prevent potential negative impacts on human health and the environment, which may arise from improper waste handling. Return the product to your dealer or contact your local authorities for more information on the nearest collection point.
To obtain an electronic version of this document (in other languages) or a version for installation in JA-100, scan the accompanying QR code.
