ElectricBikes LCD tampilan SWM5 Tampilan Layar LCD

Parameter njaba

Bahan casing: ABS
Materi tampilan: Akrilik Kekerasan Tinggi (nilai kekerasan sing padha karo kaca tempered).

Operasional Voltage lan Sambungan

1. Operasional Voltage: Kompatibel DC24V / 36V, Kompatibel 36/48V (disetel dening tampilan). Operasi liyane voltage bisa disesuaikan.
2. Konektor:
   Standard Connector Type

Atur Konektor Standar

Urutan No.	Warna Wire	Fungsi
1	Abang (VCC)	Kabel Daya Display
2	Biru (K)	Pengontrol Power On/Off Kabel
3	Ireng (GND)	Kabel Ground Display Kab
4	Ijo (RX)	Tampilan Data Receiving Wire
5	Kuning (TX)	Tampilan Data Ngirim Wire

Fungsi Extended

• Cahya: Coklat (DD): Elektroda positif saka cahya
• Putih (GND): Elektroda negatif saka cahya.

Definisi warna kabel saka PWM Voltage Motor Power Controller and the independent speed sensor will be defined otherwise.
Cathetan: Some products use waterproof connectors, whose internal wire arrangements cannot be identified from the exterior.

Fungsi

Tampilan

• Speed Display                 PAS Level Display                Battery Level Display
• Error Indication             Total Mileage                       Single Mileage
• Light Indication              Single Trip Time

Kontrol lan Setelan

• Power Switch                                               Front Light Control                6km/h Cruise Control
• Real-time Cruise Control                           Wheel Diameter Setting             Top Speed Setting
• Sleep Interval Setting                               Backlight Brightness Setting      Voltage Setelan Level

Protokol Komunikasi: UART

Rincian Tampilan

1. cahya
2. Tingkat baterei
3. Tampilan Multi-Fungsi
   • Total Mileage: ODO
   • Mileage Tunggal: TRIP
   • Error Code: Error
   • Power: WATT
   • Maintenance: Maintain
   • DST TO GO: Ora ditemtokake
4. Pangaturan gear daya kendaraan
   luwes 0-9 gir; Biasane ana 3 mode, 5 mode, 9 mode opsional (Part version 6km cart gear display P)
5. Mode Kendaraan
   • ECO: Economical Mode
   • STD: Standard Mode
   • POWER: Intensified Mode
   • SPEEDHANDLE: Handle-controlled Speed Mode
   • WALK: Walk Boost Mode
6. Tampilan kacepetan
   • Current Speed: CUR
   • Kacepetan maksimum: MAX
   • Kacepetan rata-rata: AVG
   • Unit Pengukuran: MPH utawa KM/H
     The display will calculate the actual travelling speed based on the wheel diameter and signal data (number of magnetic steel is needed for Hall motors).
7. Status Kendaraan ERROR
   Kode kesalahan lan indikasi

   Kode kesalahan (desimal)	indikasi	Cathetan
   0	Normal
   1	dilindhungi
   2	Rem
   3	Gagal Sensor PAS (tanda tunggangan)	Ora Disadari
   4	6km/j Cruise
   5	Nyata-Time Cruise
   6	Baterei sithik
   7	Motor Gagal
   8	Gagal Throttle
   9	Gagal Kontrol
   10	Komunikasi Nampa Gagal
   11	Gagal Pangiriman Komunikasi
   12	Gagal Komunikasi BMS
   13	Gagal cahya

8. Setelan
   1. P01: Padhang Lampu Latar (1: paling peteng; 3: paling padhang)
   2. P02: Unit Mileage (0: KM; 1: MILE)
   3. P03: Voltage Class 24V / 36V / 48V
   4. P04: Sleep Interval
      (0: never, other value means display sleep interval) Unit: minute
   5. P05: Power Assist Gear
      0/3 Gear Mode: Gear 1: 2V Gear 2: 3V Gear 3: 4V
      1/5 Gear Mode: Gear 1: 2V Gear 2: 2.5V Gear 3: 4V Gear 4: 3.5V Gear 5: 4V
   6. P06: Wheel Diameter Unit: inch Precision: 0.1
   7. P07: Magnet Steel Number (for Speed Test) Range: 1-100
   8. P08: Watesan kacepetan
      Range: 0-50km/h, parameter 50 nuduhake ora ana watesan kacepetan.
      1. Non-communications status (panel-controlled)
      When the current speed exceeds the speed limit, the PWM output will be shut down; when the current speed falls to lower than the speed limit, the PWM output will be activated and the driving speed will be set as the current speed ± 1km/h (only applies to assist power speed, not applicable to the handlebar speed).
      2. Status komunikasi (kontroler-kontrol)
      Kacepetan nyopir bakal tetep konstan minangka nilai winates.
      Error Value: ±1km/h (applicable to both the assist power/handlebar speed)
      Cathetan: Nilai sing kasebut ing ndhuwur diukur kanthi unit metrik (kilometer).
      When the measuring unit is switched to imperial unit (mile), the speed value displayed on the panel will be automatically switched to corresponding imperial unit, however the speed limit value in the imperial unit interface won’t change accordingly.
   9. P09: Setelan Mulai Langsung / Kick-to-Start
      0: Langsung Mulai
      1: Kick-kanggo-Mulai
   10. P10: Setelan Mode Drive
       0: Power Assist – The specific gear of the assist drive decides the assist power value. In this status the handlebar does not work.
       1: Electric Drive - Kendaraan didorong dening stang. Ing status iki, gear daya ora bisa digunakake.
       2: Power Assist + Electric Drive – Electric drive does not work in zero-start status.
   11. P11: Power Assist Sensitivity Range: 1-24
   12. P12: Power Assist Starting Intensity Range: 0-5
   13. P13: Power Magnet Steel Number 5 / 8 / 12pcs
   14. P14: Nilai Limit Saiki: 12A minangka standar; Range: 1-20A
   15. P15: Ora ditemtokake
   16. P16: ODO Zero-Out
       Long press the up key for 5 seconds and ODO value will be erased.

Operasi

Arrangement of Keys

Pambuka Kunci
Key operations involve short press, long press and long press of combination keys.
Pencet cendhak digunakake kanggo operasi sing cendhak / asring minangka:

Pencet dawa ing tombol siji digunakake kanggo ngalih status mode / on / off.
Long press on combination keys to set parameters, which can avoid misoperations (short press on combination keys is disabled to avoid misoperation).

Instructions of Keys

Adjust PAS level / Throttle level
In PAS mode

a. Pencet singkat , PAS +1.
b. Pencet singkat , PAS -1.

Ngalih Tampilan Speed

Tekan dawa + kanggo ngalih jinis tampilan kacepetan.
Enable/Disable 6km/h walk boost mode, set real-time cruise and turn on/off the lights

Nalika kendaraan diparkir, pencet dawa to enter 6km/h walk boost mode. When the vehicle is travelling, long press kanggo ngetik mode cruise nyata-wektu.
Tekan dawa to exit the cruise mode when the vehicle is in cruise 7 mode.
Tekan dawa kanggo nguripake / mateni lampu.

Nguripake / mateni Panel LCD
Nalika tampilan aktif, penet dawa lan bakal dipateni, yen ora bakal diuripake.

Switch Displayed Readings in Multi-Function Section
Pencet singkat kanggo ngalih maca ditampilake ing bagean multi-fungsi.

Setel Parameter
Tekan dawa + kanggo ngetik antarmuka setelan.

Customizable parameters include:
Wheel Diameter (unit: inch);
Magnetic Steel Number;
Backlight Brightness;
Low Voltage Ambang (deleng setelan P01-P14)

Ing antarmuka setelan, penet cendhak or to turn up/down value to the parameter, which will blink after modified. After selecting the parameter that needs to be set,

• Tekan dawa to save the current value, and the parameter will stop blinking;
• Pencet singkat kanggo ngalih menyang parameter sabanjure lan nilai sing wis disetel sadurunge bakal disimpen bebarengan.

Pencet + kanggo metu saka setelan lan nyimpen paramèter.
Without this operation, the system will automatically exit and save the modified parameters after 10 seconds.

Cathetan: Amarga upgrade produk, produk sing sampeyan tuku bisa uga rada beda karo katrangan ing manual pangguna iki, lan iki ora bakal mengaruhi panggunaan normal.

Dokumen / Sumber Daya

ElectricBikes LCD tampilan SWM5 Tampilan Layar LCD [pdf] Manual pangguna Layar LCD SWM5 Tampilan Layar LCD, tampilan LCD SWM5, Tampilan Layar LCD, Layar LCD

Referensi

• Manual pangguna