ElectricBikes LCD display SWM5 Display LCD Screen

Paramèt Eksteryè

Materyèl boîtier: ABS
Materyèl ekspozisyon: Segondè dite Acrylic (valè dite menm jan ak vè apeze).

Opere Voltage ak Koneksyon

1. Opere Voltage: DC24V / 36V Compatible, 36/48V Compatible (set by the display). Other operating voltage ka Customized.
2. Konektè:
   Standard Connector Type

Aranjman Konektè Estanda

Sekans No.	Koulè Fil	Fonksyon
1	Wouj (VCC)	Montre kab pouvwa
2	Ble (K)	Controller Power On/Off Cable
3	Nwa（GND）	Montre Ground Cable
4	Vèt (RX)	Montre Done Resevwa Fil
5	Jòn (TX)	Montre Done Voye Fil

Fonksyon pwolonje

• Light: Brown (DD): The positive electrode of the light
• White (GND): The negative electrode of the light.

The wire color definitions of the PWM Voltage Motor Power Controller and the independent speed sensor will be defined otherwise.
Nòt: Some products use waterproof connectors, whose internal wire arrangements cannot be identified from the exterior.

Fonksyon

Ekspozisyon

• Speed Display                 PAS Level Display                Battery Level Display
• Error Indication             Total Mileage                       Single Mileage
• Light Indication              Single Trip Time

Kontwòl ak Anviwònman

• Power Switch                                               Front Light Control                6km/h Cruise Control
• Real-time Cruise Control                           Wheel Diameter Setting             Top Speed Setting
• Sleep Interval Setting                               Backlight Brightness Setting      Voltage Anviwònman Nivo

Pwotokòl kominikasyon: UART

Montre Detay yo

1. Limyè
2. Nivo batri
3. Ekspozisyon milti-fonksyon
   • Kilométrage total: ODO
   • Kilométrage sèl: VWAYAJ
   • Error Code: Error
   • Power: WATT
   • Maintenance: Maintain
   • DST TO GO: Unspecified
4. Ajisteman Kovèti pou pouvwa machin
   Adjustable 0-9 gears; There are usually 3 mode, 5 mode, 9 mode optional (Part version 6km cart gear display P)
5. Mòd machin
   • ECO: Economical Mode
   • STD: Standard Mode
   • POWER: Intensified Mode
   • SPEEDHANDLE: Handle-controlled Speed Mode
   • WALK: Walk Boost Mode
6. Ekspozisyon vitès
   • Current Speed: CUR
   • Vitès maksimòm: MAX
   • Vitès Mwayèn: AVG
   • Mezire Inite: MPH oswa KM/H
     The display will calculate the actual travelling speed based on the wheel diameter and signal data (number of magnetic steel is needed for Hall motors).
7. Estati Veyikil la ERÈ
   Kòd erè ak Endikasyon

   Kòd erè (dezimal)	Endikasyon	Remak
   0	Nòmal
   1	Rezève
   2	Fren
   3	PAS Sensor Failure (mak monte)	Pa reyalize
   4	Kwazyè 6km/h
   5	Kwazyè an tan reyèl
   6	Ba batri
   7	Echèk motè
   8	Echèk gaz
   9	Echèk kontwolè
   10	Kominikasyon k ap resevwa echèk
   11	Kominikasyon Voye Echèk
   12	Echèk kominikasyon BMS
   13	Echèk limyè

8. Anviwònman
   1. P01: Klate ekleraj (1: pi fonse; 3: pi klere)
   2. P02: Inite Kilométrage (0: KM; 1: MILE)
   3. P03: Voltage Class 24V / 36V / 48V
   4. P04: Sleep Interval
      (0: never, other value means display sleep interval) Unit: minute
   5. P05: Power Assist Gear
      0/3 Gear Mode: Gear 1: 2V Gear 2: 3V Gear 3: 4V
      1/5 Gear Mode: Gear 1: 2V Gear 2: 2.5V Gear 3: 4V Gear 4: 3.5V Gear 5: 4V
   6. P06: Wou Dyamèt Inite: pous Precision: 0.1
   7. P07: Magnet Steel Number (for Speed Test) Range: 1-100
   8. P08: Limit vitès
      Ranje: 0-50km / h, paramèt 50 endike pa gen limit vitès.
      1. Non-communications status (panel-controlled)
      When the current speed exceeds the speed limit, the PWM output will be shut down; when the current speed falls to lower than the speed limit, the PWM output will be activated and the driving speed will be set as the current speed ± 1km/h (only applies to assist power speed, not applicable to the handlebar speed).
      2. Estati kominikasyon (kontwolè-kontwole)
      Vitès kondwi a ap kenbe konstan kòm valè limite a.
      Error Value: ±1km/h (applicable to both the assist power/handlebar speed)
      Nòt: Valè yo mansyone anwo yo mezire pa inite metrik (kilomèt).
      When the measuring unit is switched to imperial unit (mile), the speed value displayed on the panel will be automatically switched to corresponding imperial unit, however the speed limit value in the imperial unit interface won’t change accordingly.
   9. P09: Kòmanse dirèk / Anviwònman Kick-to-Start
      0: Kòmanse dirèk
      1: Choute-pou-Kòmanse
   10. P10: Kondwi Mode Anviwònman
       0: Power Assist – The specific gear of the assist drive decides the assist power value. In this status the handlebar does not work.
       1: Kondwi elektrik - Se gidon an kondwi machin nan. Nan sitiyasyon sa a Kovèti pou pouvwa a pa travay.
       2: Power Assist + Electric Drive – Electric drive does not work in zero-start status.
   11. P11: Power Assist Sensitivity Range: 1-24
   12. P12: Power Assist Starting Intensity Range: 0-5
   13. P13: Power Magnet Steel Number 5 / 8 / 12pcs
   14. P14: Valè limit aktyèl: 12A pa default; Ranje: 1-20A
   15. P15: Pa espesifye
   16. P16: ODO Zero-Out
       Long press the up key for 5 seconds and ODO value will be erased.

Operasyon yo

Arrangement of Keys

Entwodiksyon nan kle
Key operations involve short press, long press and long press of combination keys.
Kout laprès yo itilize pou operasyon kout / souvan tankou:

Long peze sou yon sèl kle yo itilize pou chanje estati mòd / sou / koupe.
Long press on combination keys to set parameters, which can avoid misoperations (short press on combination keys is disabled to avoid misoperation).

Instructions of Keys

Adjust PAS level / Throttle level
In PAS mode

yon. Kout laprès , PAS +1.
b. Kout laprès , PAS -1.

Chanje Vitès Display

Long peze + chanje kalite ekspozisyon vitès.
Enable/Disable 6km/h walk boost mode, set real-time cruise and turn on/off the lights

Lè machin nan pake, peze long to enter 6km/h walk boost mode. When the vehicle is travelling, long press pou antre nan mòd kwazyè an tan reyèl.
Long peze to exit the cruise mode when the vehicle is in cruise 7 mode.
Long peze pou limen/éteindre limyè yo.

Limen / etenn LCD Panel la
When the display is in operation, long press epi li pral etenn, otreman li pral limen.

Switch Displayed Readings in Multi-Function Section
Kout laprès pou chanje lekti yo montre nan seksyon milti-fonksyon an.

Mete Paramèt
Long peze + pou antre nan koòdone anviwònman an.

Customizable parameters include:
Wheel Diameter (unit: inch);
Magnetic Steel Number;
Backlight Brightness;
Low Voltage Threshold (refer to setting P01-P14)

Nan koòdone anviwònman an, kout peze or to turn up/down value to the parameter, which will blink after modified. After selecting the parameter that needs to be set,

• Long peze to save the current value, and the parameter will stop blinking;
• Kout laprès pou chanje nan pwochen paramèt la epi yo pral sove valè a te deja mete an menm tan an.

Peze + pou sòti nan anviwònman an epi sove paramèt yo.
Without this operation, the system will automatically exit and save the modified parameters after 10 seconds.

Nòt: Akòz amelyorasyon pwodwi, pwodwi ou achte a ka yon ti kras diferan de deskripsyon yo nan manyèl itilizatè sa a, epi sa a pa pral afekte itilizasyon nòmal.

Dokiman / Resous

ElectricBikes LCD display SWM5 Display LCD Screen [pdfManyèl Itilizatè LCD display SWM5 Display LCD Screen, LCD display SWM5, Display LCD Screen, LCD Screen

Referans

• Manyèl itilizatè