Fa'aaliga LCD uila eletise SWM5 Fa'aali mata LCD
Parameter fafo
Mea fa'apipi'i: ABS
Fa'aaliga Mea: Maaa Maualuluga Acrylic (e tutusa le taua ma le maaa maa tioata).
Faagaioiga Voltage ma So'oga
- Faagaioiga Voltage: DC24V / 36V Fesoʻotaʻi, 36/48V Fesoʻotaʻi (faʻapipiʻi e le faʻaaliga). O isi galuega voltage mafai ona fa'atulagaina.
- Feso'ota'i:
Standard Connector Type
Fuafuaga Feso'ota'i
| Fa'asologa Nu. | Lanu Uaea | Galuega |
| 1 | Mumu（VCC） | Fa'aali Uaea Malosi |
| 2 | Blue(K) | Pule Malosi I/Pepe Uaea |
| 3 | uliuli(GND) | Fa'aali Uaea eleele |
| 4 | lanumeamata（RX） | Fa'aali Fa'amatalaga Mauaina Uaea |
| 5 | samasama（TX） | Fa'aali Fa'amatalaga Tuuina Atu Uaea |
Galuega Fa'alautele
- Malamalama: Enaena (DD): Le eletise lelei o le moli
- Pa'epa'e (GND): Le eletise le lelei o le moli.
O fa'amatalaga lanu uaea o le PWM Voltage Motor Power Controller and the independent speed sensor will be defined otherwise.
Fa'aaliga: Some products use waterproof connectors, whose internal wire arrangements cannot be identified from the exterior.
Galuega
Fa'aaliga
- Speed Display PAS Level Display Battery Level Display
- Error Indication Total Mileage Single Mileage
- Light Indication Single Trip Time
Pulea ma Fa'atonu
- Power Switch Front Light Control 6km/h Cruise Control
- Real-time Cruise Control Wheel Diameter Setting Top Speed Setting
- Sleep Interval Setting Backlight Brightness Setting Voltagu Fa'atulagaina Tulaga
Fesootaiga Fesootaiga: UART
Faʻaali auiliiliga
- Malamalama
- Tulaga ma'a
- Fa'aaliga Tele-Functions
- Aofa'i Maile: ODO
- Maile Nofofua: TRIP
- Error Code: Error
- Power: WATT
- Maintenance: Maintain
- DST TO GO: Le fa'ailoaina
Fetuunaiga o mea e fa'aogaina ai le eletise
Fa'atonu 0-9 mea fa'aoga; E masani ona i ai le 3 mode, 5 mode, 9 auala e filifili ai (Vaega vaega 6km faʻataʻavalevale taavale P)- Faiga ta'avale
- ECO: Economical Mode
- STD: Standard Mode
- POWER: Intensified Mode
- SPEEDHANDLE: Handle-controlled Speed Mode
- WALK: Walk Boost Mode
- Fa'aaliga Saosaoa
- Current Speed: CUR
- Saosaoa Maualuluga: MAX
- Vave ole Saosaoa: AVG
- Fua Vaega: MPH poʻo KM/H
The display will calculate the actual travelling speed based on the wheel diameter and signal data (number of magnetic steel is needed for Hall motors).
Tulaga Ta'avale SESE
Fa'ailoga sese ma Fa'ailogaFa'ailoga sese (decimal) Fa'ailoga Manatua 0 masani 1 Fa'apolopolo 2 Taofi 3 Fai le PAS Sensor (fa'ailoga ti'eti'e) Le iloa 4 6km/h Fa'a folau 5 Va'a Taimi Moni 6 Ma'a maualalo 7 Ua faaletonu le afi 8 Fa'aletonu le fa'auila 9 Fa'aletonu le Pule 10 Feso'ota'iga Mauaina Fa'aletonu 11 Feso'ota'iga Auina atu le manuia 12 Fa'aletonu Feso'ota'iga BMS 13 Malamalama Faigofie - Fa'atonu
- P01: Malamalama i tua (1: pogisa; 3: sili ona susulu)
- P02: Iunite maila (0: KM; 1: MILE)
- P03: Voltage Class 24V / 36V / 48V
- P04: Sleep Interval
(0: never, other value means display sleep interval) Unit: minute - P05: Power Assist Gear
0/3 Gear Mode: Gear 1: 2V Gear 2: 3V Gear 3: 4V
1/5 Gear Mode: Gear 1: 2V Gear 2: 2.5V Gear 3: 4V Gear 4: 3.5V Gear 5: 4V - P06: Uili Diameter Unit: inisi Sa'o: 0.1
- P07: Magnet Steel Number (for Speed Test) Range: 1-100
- P08: Tapulaa Saosaoa
Va'aiga: 0-50km/h, fa'amaufa'ailoga 50 fa'ailoa mai e leai se saoasaoa fa'atapula'aina.
1. Non-communications status (panel-controlled)
When the current speed exceeds the speed limit, the PWM output will be shut down; when the current speed falls to lower than the speed limit, the PWM output will be activated and the driving speed will be set as the current speed ± 1km/h (only applies to assist power speed, not applicable to the handlebar speed).
2. Tulaga o Feso'ota'iga (pule-pulea)
Ole saosaoa ole aveta'avale ole a fa'atumauina pea e pei ole tau fa'atapula'aina.
Error Value: ±1km/h (applicable to both the assist power/handlebar speed)
Fa'aaliga: O tau o lo'o ta'ua i luga o lo'o fuaina ile metric unit (kilomita).
When the measuring unit is switched to imperial unit (mile), the speed value displayed on the panel will be automatically switched to corresponding imperial unit, however the speed limit value in the imperial unit interface won’t change accordingly. - P09: Fa'atonu Amata / Kiki-i-Amata
0: Amata tuusao
1: Kick-i-Amata - P10: Fa'atulagaina o le Avetaavale
0: Power Assist – The specific gear of the assist drive decides the assist power value. In this status the handlebar does not work.
1: Eletise Avega - O le taʻavale e faʻauluina e le au. I lenei tulaga e le o galue le masini eletise.
2: Power Assist + Electric Drive – Electric drive does not work in zero-start status. - P11: Power Assist Sensitivity Range: 1-24
- P12: Power Assist Starting Intensity Range: 0-5
- P13: Power Magnet Steel Number 5 / 8 / 12pcs
- P14: Tau Fa'atapula'a o lo'o i ai nei: 12A ona o le faaletonu; Va'aiga: 1-20A
- P15: Le fa'ailoaina
- P16: ODO Zero-Out
Long press the up key for 5 seconds and ODO value will be erased.
Galuega
Arrangement of Keys
Folasaga o Ki
Key operations involve short press, long press and long press of combination keys.
O lomitusi pupuu e fa'aaogaina mo galuega pu'upu'u/fai soo e pei o:
Oomi umi i luga o se ki se tasi e faʻaaogaina e sui ai le tulaga / on / off tulaga.
Long press on combination keys to set parameters, which can avoid misoperations (short press on combination keys is disabled to avoid misoperation).
Instructions of Keys
Adjust PAS level / Throttle level
In PAS mode
a. Tusitala puupuu 
, PAS +1.
e. Puupuu lomitusi 
, PAS -1.
Fa'aali Saosaoa Suiga
Oomi umi 
+ e fesuia'i ituaiga fa'aaliga saosaoa.
Enable/Disable 6km/h walk boost mode, set real-time cruise and turn on/off the lights
A tu le taavale, oomi umi to enter 6km/h walk boost mode. When the vehicle is travelling, long press e ulufale i le taimi moni faiga folau.
Oomi umi to exit the cruise mode when the vehicle is in cruise 7 mode.
Oomi umi e ki/tapē moli.
Ki / tape le LCD Panel
A fa'aalia le fa'aaliga, oomi umi ma o le a tapēina, a leai o le a ola.
Switch Displayed Readings in Multi-Function Section
Tusitala puupuu e fesuiai faitauga o loʻo faʻaalia i le vaega tele-galuega.
Seti Parameter
Oomi umi + e ulu atu i le faʻaoga faʻatulagaina.
Customizable parameters include:
Wheel Diameter (unit: inch);
Magnetic Steel Number;
Backlight Brightness;
Maualalo Voltagu Avanoa (silasila ile seti P01-P14)
I totonu o le fa'atulagaina o feso'ota'iga, lolomi pu'upu'u or to turn up/down value to the parameter, which will blink after modified. After selecting the parameter that needs to be set,
- Oomi umi to save the current value, and the parameter will stop blinking;
- Tusitala puupuu e fesuiai i le isi parakalafa ma le tau faatulagaina muamua o le a faasaoina i le taimi e tasi.
Tusitala + e alu ese mai le seti ma faʻasaoina faʻamaufaʻailoga.
Without this operation, the system will automatically exit and save the modified parameters after 10 seconds.
Fa'aaliga: Ona o le fa'aleleia o oloa, o le oloa na e fa'atauina e ono ese teisi mai fa'amatalaga i totonu o lenei tusi fa'aoga, ma e le afaina ai le fa'aoga masani.
Pepa / Punaoa
 |
Fa'aaliga LCD uila eletise SWM5 Fa'aali mata LCD [pdf] Tusi Taiala Fa'aaliga LCD SWM5 Fa'aali LCD Mata, Fa'aaliga LCD SWM5, Fa'aaliga LCD, Fa'aaliga LCD |