ElectricBikes-Logo

ElectricBikes LCD display SWM5 Display LCD Screen

ElectricBikes-LCD-display-SWM5-Display-LCD-Screen

Mga Parameter sa gawas

Materyal nga Casing: ABS
Ipakita ang Materyal: Taas nga Katig-a sa Acrylic (ang parehas nga katig-a nga kantidad sa tempered nga baso).

ElectricBikes-LCD-display-SWM5-Display-LCD-Screen-1

ElectricBikes-LCD-display-SWM5-Display-LCD-Screen-2

Ang Operating Voltage ug Koneksyon

  1. Ang Operating Voltage: DC24V / 36V Compatible, 36/48V Compatible (set by the display). Other operating voltage mahimong ipasadya.
  2. Mga Konektor:
    Standard Connector Type

ElectricBikes-LCD-display-SWM5-Display-LCD-Screen-3

Standard Connector Arrangement

Han-ay sa Numero Kolor sa Wire Mga gimbuhaton
1 Pula (VCC) Ipakita ang Power Cable
2 Asul (K) Controller Power On/Off Cable
3 Itom (GND) Ipakita ang Ground Cable
4 Berde(RX) Ipakita ang Data Receiving Wire
5 Dilaw(TX) Ipakita ang Data Sending Wire

Gipadako nga mga Kalihokan

  • Light: Brown (DD): The positive electrode of the light
  • White (GND): The negative electrode of the light.

The wire color definitions of the PWM Voltage Motor Power Controller and the independent speed sensor will be defined otherwise.
Mubo nga sulat: Some products use waterproof connectors, whose internal wire arrangements cannot be identified from the exterior.

Mga gimbuhaton

Pagpakita

  • Speed Display                 PAS Level Display                Battery Level Display
  • Error Indication             Total Mileage                       Single Mileage
  • Light Indication              Single Trip Time

Pagpugong ug mga setting

  • Power Switch                                               Front Light Control                6km/h Cruise Control
  • Real-time Cruise Control                           Wheel Diameter Setting             Top Speed Setting
  • Sleep Interval Setting                               Backlight Brightness Setting      Voltage Setting sa lebel

Protokol sa Komunikasyon: UART

ElectricBikes-LCD-display-SWM5-Display-LCD-Screen-4

Ipakita ang mga Detalye

  1. Kahayag
  2. Ang lebel sa Baterya
  3. Multi-Functions Display
    • Kinatibuk-ang Mileage: ODO
    • Usa ka Mileage: Biyahe
    • Error Code: Error
    • Power: WATT
    • Maintenance: Maintain
    • DST TO GO: Unspecified
  4. ElectricBikes-LCD-display-SWM5-Display-LCD-Screen-5Pag-adjust sa galamiton sa kuryente sa sakyanan
    Adjustable 0-9 gears; There are usually 3 mode, 5 mode, 9 mode optional (Part version 6km cart gear display P)
  5. Mode sa Salakyanan
    • ECO: Economical Mode
    • STD: Standard Mode
    • POWER: Intensified Mode
    • SPEEDHANDLE: Handle-controlled Speed Mode
    • WALK: Walk Boost Mode
  6. Speed ​​Display
    • Current Speed: CUR
    • Kinatas-ang Bilis: MAX
    • Average nga Speed: AVG
    • Yunit sa Pagsukod: MPH o KM/H
      The display will calculate the actual travelling speed based on the wheel diameter and signal data (number of magnetic steel is needed for Hall motors).
  7. ElectricBikes-LCD-display-SWM5-Display-LCD-Screen-6Status sa Salakyanan SAYOP
    Error Code ug mga Indikasyon
    Error Code (decimal) Mga timailhan Nota
    0 Normal  
    1 Gireserba  
    2 Brake  
    3 Pagkapakyas sa PAS Sensor (marka sa pagsakay) Wala nakaamgo
    4 6km/h Paglayag  
    5 Tinuod nga Oras nga Paglayag  
    6 Ubos nga Baterya  
    7 Pagkapakyas sa Motor  
    8 Pagkapakyas sa Throttle  
    9 Kapakyasan sa Controller  
    10 Kapakyasan sa Pagdawat sa Komunikasyon  
    11 Kapakyasan sa Pagpadala sa Komunikasyon  
    12 Kapakyasan sa BMS Communications  
    13 Kapakyasan sa Kahayag  
  8. Mga setting
    1. P01: Kahayag sa Backlight (1: pinakangitngit; 3: labing hayag)
    2. P02: Mileage Unit (0: KM; 1: MILE)
    3. P03: Tomotage Class 24V / 36V / 48V
    4. P04: Sleep Interval
      (0: never, other value means display sleep interval) Unit: minute
    5. P05: Power Assist Gear
      0/3 Gear Mode: Gear 1: 2V Gear 2: 3V Gear 3: 4V
      1/5 Gear Mode: Gear 1: 2V Gear 2: 2.5V Gear 3: 4V Gear 4: 3.5V Gear 5: 4V
    6. P06: Wheel Diameter Unit: pulgada Katukma: 0.1
    7. P07: Magnet Steel Number (for Speed Test) Range: 1-100
    8. P08: Speed ​​Limit
      Range: 0-50km/h, parameter 50 nagpakita nga walay speed limit.
      1. Non-communications status (panel-controlled)
      When the current speed exceeds the speed limit, the PWM output will be shut down; when the current speed falls to lower than the speed limit, the PWM output will be activated and the driving speed will be set as the current speed ± 1km/h (only applies to assist power speed, not applicable to the handlebar speed).
      2. Status sa komunikasyon (kontrolado sa controller)
      Ang katulin sa pagmaneho magpabilin nga makanunayon ingon nga limitado nga kantidad.
      Error Value: ±1km/h (applicable to both the assist power/handlebar speed)
      Mubo nga sulat: Ang nahisgutan nga mga kantidad gisukod sa metric unit (kilometro).
      When the measuring unit is switched to imperial unit (mile), the speed value displayed on the panel will be automatically switched to corresponding imperial unit, however the speed limit value in the imperial unit interface won’t change accordingly.
    9. P09: Direktang Pagsugod / Sipa-sa-Pagsugod nga Setting
      0: Direktang Pagsugod
      1: Sipa-sa-Pagsugod
    10. P10: Pag-set sa Mode sa Pagmaneho
      0: Power Assist – The specific gear of the assist drive decides the assist power value. In this status the handlebar does not work.
      1: Electric Drive - Ang sakyanan gimaneho sa handlebar. Niini nga kahimtang ang power gear dili molihok.
      2: Power Assist + Electric Drive – Electric drive does not work in zero-start status.
    11. P11: Power Assist Sensitivity Range: 1-24
    12. P12: Power Assist Starting Intensity Range: 0-5
    13. P13: Power Magnet Steel Number 5 / 8 / 12pcs
    14. P14: Kasamtangang Limitasyon nga Bili: 12A pinaagi sa default; Sakup: 1-20A
    15. P15: Dili matino
    16. P16: ODO Zero-Out
      Long press the up key for 5 seconds and ODO value will be erased.

Mga operasyon

Arrangement of Keys

ElectricBikes-LCD-display-SWM5-Display-LCD-Screen-7

Pasiuna sa mga Yawi
Key operations involve short press, long press and long press of combination keys.
Ang mugbo nga press kay gigamit para sa mugbo/subsob nga mga operasyon sama sa:

ElectricBikes-LCD-display-SWM5-Display-LCD-Screen-8

Ang dugay nga pagpindot sa usa ka yawe kay gigamit sa switch mode/on/off status.
Long press on combination keys to set parameters, which can avoid misoperations (short press on combination keys is disabled to avoid misoperation).

Instructions of Keys

Adjust PAS level / Throttle level
In PAS mode

a. Mubo nga press ElectricBikes-LCD-display-SWM5-Display-LCD-Screen-10, PAS +1.
b. Mubo nga press ElectricBikes-LCD-display-SWM5-Display-LCD-Screen-11, PAS -1.

Pagbalhin sa Speed ​​​​Display

Dugay nga press ElectricBikes-LCD-display-SWM5-Display-LCD-Screen-9 + ElectricBikes-LCD-display-SWM5-Display-LCD-Screen-10 sa pagbalhin sa speed display type.
Enable/Disable 6km/h walk boost mode, set real-time cruise and turn on/off the lights

Kung naka-park ang sakyanan, pugngi ug dugay ElectricBikes-LCD-display-SWM5-Display-LCD-Screen-11 to enter 6km/h walk boost mode. When the vehicle is travelling, long press ElectricBikes-LCD-display-SWM5-Display-LCD-Screen-11 aron makasulod sa real-time nga cruise mode.
Dugay nga press ElectricBikes-LCD-display-SWM5-Display-LCD-Screen-11 to exit the cruise mode when the vehicle is in cruise 7 mode.
Dugay nga press ElectricBikes-LCD-display-SWM5-Display-LCD-Screen-10 aron i-on/off ang mga suga.

I-on/i-off ang LCD Panel
When the display is in operation, long press ElectricBikes-LCD-display-SWM5-Display-LCD-Screen-9 ug kini palongon, kay kon dili kini i-on.

Switch Displayed Readings in Multi-Function Section
Mubo nga press ElectricBikes-LCD-display-SWM5-Display-LCD-Screen-9 aron ibalhin ang mga pagbasa nga gipakita sa seksyon nga multi-function.

Ibutang ang mga Parameter
Dugay nga press ElectricBikes-LCD-display-SWM5-Display-LCD-Screen-10 + ElectricBikes-LCD-display-SWM5-Display-LCD-Screen-11 sa pagsulod sa setting interface.

Customizable parameters include:
Wheel Diameter (unit: inch);
Magnetic Steel Number;
Backlight Brightness;
Ubos nga Voltage Threshold (refer to setting P01-P14)

Sa interface sa setting, mubo nga press ElectricBikes-LCD-display-SWM5-Display-LCD-Screen-10 or ElectricBikes-LCD-display-SWM5-Display-LCD-Screen-11 to turn up/down value to the parameter, which will blink after modified. After selecting the parameter that needs to be set,

  • Dugay nga press ElectricBikes-LCD-display-SWM5-Display-LCD-Screen-9 to save the current value, and the parameter will stop blinking;
  • Mubo nga press ElectricBikes-LCD-display-SWM5-Display-LCD-Screen-9 sa pagbalhin ngadto sa sunod nga parameter ug ang kaniadto gitakda nga bili maluwas sa samang higayon.

Press ElectricBikes-LCD-display-SWM5-Display-LCD-Screen-10 + ElectricBikes-LCD-display-SWM5-Display-LCD-Screen-11 aron mogawas sa setting ug i-save ang mga parameter.
Without this operation, the system will automatically exit and save the modified parameters after 10 seconds.

Mubo nga sulat: Tungod sa pag-upgrade sa produkto, ang produkto nga imong gipalit mahimong lahi gamay sa mga paghulagway niini nga manwal sa paggamit, ug kini dili makaapekto sa normal nga paggamit.

Mga Dokumento / Mga Kapanguhaan

ElectricBikes LCD display SWM5 Display LCD Screen [pdf] Manwal sa Gumagamit
LCD display SWM5 Display LCD Screen, LCD display SWM5, Display LCD Screen, LCD Screen

Mga pakisayran

Pagbilin ug komento

Ang imong email address dili mamantala. Ang gikinahanglan nga mga natad gimarkahan *