ARDUINO ABX00053 Nano RP2040 Jikọọ na ntuziaka onye ọrụ
Nkọwa
Njirimara juru n'ọnụ Arduino® Nano RP2040 Jikọọ na-eweta Raspberry Pi RP2040 microcontroller ọhụrụ na ụdị Nano. Mee ọtụtụ n'ime akụkụ abụọ nke isi 32-bit Arm® Cortex®-M0+ ka ijikọ njikọ Bluetooth® na Wi-Fi rụọ ọrụ ịntanetị nke ihe site na modul U-blox® Nina W102. Banye n'ime ọrụ ụwa n'ezie na ngwa ngwa ngwa ngwa, gyroscope, RGB LED na igwe okwu. Mepụta ngwọta AI siri ike agbakwunyere na obere mbọ iji Arduino® Nano RP2040 Jikọọ!
Mpaghara ebumnuche
Ịntanetị nke Ihe (IoT), mmụta igwe, prototyping,
Atụmatụ
Raspberry Pi RP2040 Microcontroller
- 133MHz 32bit Dual Core Arm® Cortex®-M0+
- 264kB on-chip SRAM
- Direct ebe nchekwa Access (DMA) njikwa
- Nkwado maka ihe ruru 16MB nke ebe nchekwa Flash na-apụ apụ site na ụgbọ ala QSPI raara onwe ya nye
- USB 1.1 njikwa na PHY, nwere onye nnabata na nkwado ngwaọrụ
- Igwe steeti PIO 8
- IO (PIO) nwere ike ime maka nkwado mpụta gbatịpụrụ
- 4 ọwa ADC nwere ihe mmetụta okpomọkụ dị n'ime, 0.5 MSa/s, ntụgharị 12-bit
- Nchọpụta SWD
- 2 na-chip PLL iji mepụta USB na isi elekere
- 40nm usoro ọnụ
- Nkwado ụdị ike dị ala ọtụtụ
- USB 1.1 onye ọbịa / ngwaọrụ
- Ime Voltage Regulator inye isi voltage
- Ụgbọ ala na-arụ ọrụ dị elu (AHB)/Bus peripheral Advanced (APB)
U-blox® Nina W102 Wi-Fi/Bluetooth® Module
- 240MHz 32bit Dual Core Xtensa LX6
- 520kB on-chip SRAM
- 448 Kbyte ROM maka booting na isi ọrụ
- 16 Mbit FLASH maka nchekwa koodu gụnyere izo ya ezo ngwaike iji chebe mmemme na data
- 1 kbit EFUSE (ebe nchekwa anaghị ehichapụ) maka adreesị MAC, nhazi modul, Flash-Encryption, na Chip-ID
- IEEE 802.11b/g/n otu-band 2.4 GHz Wi-Fi arụ ọrụ
- Njikọ Bluetooth® 4.2
- Ejikọtara Planar Inverted-F Antenna (PIFA)
- 4 x 12-bit ADC
- 3x I2C, SDIO, CAN, QSPI
Ebe nchekwa
- AT25SF128A 16MB ma ọ bụ Flash
- Ọnụego mbufe data QSPI ruru 532Mbps
- 100K mmemme / ihichapụ okirikiri
ST LSM6DSOXTR 6-axis IMU
- Gyroscope 3D
- ± 2 / ± 4 / ± 8 / ± 16 g zuru oke
- 3D Accelerometer
- ± 125 / ± 250 / ± 500 / ± 1000 / 2000 dps zuru oke
- Pedometer dị elu, ihe nchọpụta nzọụkwụ na counter nzọụkwụ
- Nchọpụta ngagharị dị mkpa, nchọpụta tilt
- Ọkọlọtọ nkwụsị: ọdịda efu, iteta, nghazi 6D/4D, pịa wee pịa ugboro abụọ.
- Igwe steeti nwere ngwụcha mmemme nwere ike ime: accelerometer, gyroscope na sensọ mpụga
- Isi mmụta igwe
- Ihe mmetụta okpomọkụ agbakwunyere
Igwe okwu ST MP34DT06JTR MEMS
- AOP = 122.5 dBSPL
- Oke mgbama na mkpọtụ 64dB
- Mmetụta uche n'ebe niile
- -26 dBFS ± 1 dB uche
RGB LED
- Anode nkịtị
- Jikọọ na U-blox® Nina W102 GPIO
Microchip® ATECC608A Crypto
- Onye na-arụkọ ọrụ Cryptographic nwere nchekwa igodo dabere na ngwaike echekwara
- I2C, SWI
- Nkwado ngwaike maka Algorithms Symmetric:
- SHA-256 & HMAC Hash gụnyere ichekwa ma ọ bụ weghachi ọnọdụ ndị na-apụ apụ
- AES-128: Encrypt/Decrypt, Galois Field Multiply for GCM
- Ọdịmma dị elu nke ime NIST SP 800-90A/B/C Ndị na-emepụta ọnụọgụ ọnụọgụ (RNG)
- Nkwado buut echekwara:
- Nkwenye mbinye aka koodu ECDSA zuru oke, mgbari / mbinye aka echekwara nhọrọ
- Nkwụsị igodo nkwurịta okwu nhọrọ tupu ị nweta buut
- Izo ya ezo/Nnwale maka ozi iji gbochie mwakpo n'ime ụgbọ
I/O
- 14x Digital Pin
- 8x Analog Pin
- Micro USB
- Nkwado UART, SPI, I2C
Ike
- Buck mgbada mgbada
Ozi nchekwa
- Klas A
The Board
Ngwa Examples
Enwere ike ịmegharị njikọ Arduino® Nano RP2040 ka ọ bụrụ usoro eji eme ihe n'ọtụtụ ebe ekele maka microprocessor dị ike, oke sensọ onboard na ụdị Nano. Ngwa enwere ike gụnyere:
Kọmputa Edge: Jiri ngwa ngwa RAM microprocessor dị elu iji mee TinyML maka nchọpụta anomaly, nchọpụta ụkwara, nyocha mmegharị ahụ na ihe ndị ọzọ.
Ngwa ndị nwere ike eyi: Obere akara ukwu Nano na-enye ohere nke ịnye igwe mmụta igwe na ngwaọrụ dị iche iche na-eyi egwu gụnyere ndị na-egwu egwuregwu na ndị na-ahụ maka VR.
Onye enyemaka olu: Njikọ Arduino® Nano RP2040 gụnyere igwe okwu omnidirectional nke nwere ike ịrụ ọrụ dị ka onye enyemaka dijitalụ nkeonwe ma mee ka njikwa olu rụọ ọrụ gị.
Ngwa ngwa
- Igwe USB Micro
- 15-pin 2.54mm nkụnye eji isi mee nwoke
- 15-pin 2.54mm nkụnye eji isi mee
Ngwaahịa ndị emetụtara
Ike ndọda: Nano I/O Shield
Ogo
Ọnọdụ ọrụ akwadoro
| Akara | Nkọwa | Min | Ụdị | Oke | Nkeji |
| VIN | Ntinye voltage sitere na VIN pad | 4 | 5 | 20 | V |
| VUSB | Ntinye voltage site na njikọ USB | 4.75 | 5 | 5.25 | V |
| V3V3 | 3.3V mmepụta na ngwa onye ọrụ | 3.25 | 3.3 | 3.35 | V |
| I3V3 | 3.3V mmepụta ugbu a (gụnyere onboard IC) | – | – | 800 | mA |
| VIH | Tinye ọkwa dị elu voltage | 2.31 | – | 3.3 | V |
| VIL | Tinye obere ọkwa voltage | 0 | – | 0.99 | V |
| Ọnụ ego nke IOH Max | Ugbu a na VDD-0.4 V, mmepụta setịpụrụ elu | 8 | mA | ||
| IOL Max | Ugbu a na VSS+0.4 V, ewepụtarala ihe nrụpụta dị ala | 8 | mA | ||
| VOH | Mmepụta elu voltage, 8mA | 2.7 | – | 3.3 | V |
| VOL | Mmepụta obere voltage, 8mA | 0 | – | 0.4 | V |
| N'elu | Okpomọkụ na-arụ ọrụ | -20 | – | 80 | Celsius C |
Oriri ike
| Akara | Nkọwa | Min | Ụdị | Oke | Nkeji |
| PBL | Oriri ike na akaghị aka | TBC | mW | ||
| PLP | Oriri ike na ọnọdụ ike dị ala | TBC | mW | ||
| PMAX | Oriri ike kacha | TBC | mW |
Arụ ọrụ gafereview
Ihe Ngosi
Board Topology
N'ihu View
| Ref. | Nkọwa | Ref. | Nkọwa |
| U1 | Raspberry Pi RP2040 Microcontroller | U2 | Ublox NINA-W102-00B Wi-Fi/Bluetooth® Module |
| U3 | N/A | U4 | ATECC608A-MAHDA-T Crypto IC |
| U5 | AT25SF128A-MHB-T 16MB Flash IC | U6 | MP2322GQH Onye na-achịkwa Buck-down |
| U7 | DSC6111HI2B-012.0000 MEMS Oscillator | U8 | MP34DT06JTR MEMS Omnidirectional igwe okwu IC |
| U9 | LSM6DSOXTR 6-axis IMU nwere isi mmụta igwe | J1 | Njikọ Micro USB nwoke |
| DL1 | Ike Green Na LED | DL2 | Wuru Oroma LED |
| DL3 | RGB Common Anode LED | PB1 | Tọgharịa bọtịnụ |
| JP2 | Analog Pin + D13 Pin | JP3 | Ntụtụ dijitalụ |
Azu View
| Ref. | Nkọwa | Ref. | Nkọwa |
| SJ4 | 3.3V jumper (jikọrọ) | SJ1 | VUSB jumper (kwụpụrụ) |
Nhazi
Ihe nhazi ahụ dabere na silicon Raspberry Pi RP2040 ọhụrụ (U1). Igwe njikwa micro a na-enye ohere maka mmepe ịntanetị nke ihe dị ala yana mmụta igwe agbakwunyere. Abụọ symmetrical Arm® Cortex®-M0+ mechiri na 133MHz na-enye ike mgbako maka mmụta igwe agbakwunyere yana nhazi ya na obere ike. Enyere ụlọ akụ isii kwụụrụ onwe ya nke 264 KB SRAM na 2MB. Nweta ebe nchekwa ozugbo na-enye njikọ ngwa ngwa n'etiti ndị na-arụ ọrụ na ebe nchekwa nwere ike ime ka ọ ghara ịdị na-arụ ọrụ yana isi ịbanye ọnọdụ ụra. Serial waya debug (SWD) dị site na buut site na pads n'okpuru osisi. RP2040 na-agba na 3.3V ma nwee volta dị n'imetage regulator na-enye 1.1V.
RP2040 na-achịkwa mpụta na ntụtụ dijitalụ, yana atụdo analọg (A0-A3). A na-eji njikọ I2C dị na pin A4 (SDA) na A5 (SCL) maka ijikọ na akụkụ ndị dị n'ụgbọ mmiri ma jiri 4.7 kΩ resistor bulie ya. SWD Clock Line (SWCLK) na nrụpụta na-ejiri 4.7 kΩ resistor na-ebulikwa ya. Ihe oscillator MEMS dị na mpụga (U7) na-agba ọsọ na 12MHz na-enye ụda elekere. Programmable IO na-enyere aka na mmejuputa usoro nkwurịta okwu aka ike na ibu dị nta na isi nhazi isi. Ejiri interface ngwaọrụ USB 1.1 na RP2040 maka ibugo koodu.
Njikọ Wi-Fi/Bluetooth®
Enyere njikọ Wi-Fi na Bluetooth® site na modul Nina W102 (U2). RP2040 nwere naanị 4 ntụtụ analọgụ, a na-ejikwa Nina gbatịa nke ahụ ruo asatọ zuru oke dịka ọkọlọtọ na ụdị Arduino Nano nwere ntinye analọgụ 4 12-bit ọzọ (A4-A7). Na mgbakwunye, ihe Nina W-102 modul na-achịkwa anode RGB LED nke na-eme ka ọkụ na-apụ mgbe steeti dijitalụ dị elu yana na mgbe steeti dijitalụ dị ala. Igwe PCB dị n'ime n'ime modul na-ewepụ mkpa maka antenna mpụga. Nina W102 modul tinyekwara a dual core Xtensa LX6 CPU nke nwekwara ike hazie onwe ya na RP2040 site na pads n'okpuru bọọdụ iji SWD.
6-Axis IMU
Ọ ga-ekwe omume ịnweta gyroscope 3D na data accelerometer 3D site na LSM6DSOX 6-axis IMU (U9). Na mgbakwunye na ịnye data dị otú ahụ, ọ ga-ekwe omume ịme mmụta igwe na IMU maka nchọpụta mmegharị ahụ.
Ebe nchekwa mpụga
RP2040 (U1) nwere ohere ịnweta 16 MB nke ebe nchekwa ọkụ site na interface QSPI. Ihe nrụnye-in-ebe (XIP) nke RP2040 na-enye ohere ka sistemụ ahụ wee nweta ebe nchekwa flash mpụga dị ka a ga-asị na ọ bụ ebe nchekwa dị n'ime, na-ebughị ụzọ degharịa koodu ahụ na ebe nchekwa dị n'ime.
Cryptography
ATECC608A Cryptographic IC (U4) na-enye ike buut echekwara n'akụkụ SHA na AES-128 nkwado nzuzo / decryption maka nchekwa na ngwa Smart Home na Industrial IoT (IIoT). Na mgbakwunye, onye na-emepụta nọmba random dịkwa maka RP2040.
Igwe okwu
Ejikọrọ igwe okwu MP34DT06J site na interface PDM na RP2040. Igwe okwu MEMS dijitalụ bụ akụkụ niile ma na-arụ ọrụ site na mmetụ mmetụta nwere nnukwu mgbama (64 dB) maka oke mkpọtụ. A na-arụpụta ihe na-ahụ ihe, nke nwere ike ịchọpụta ebili mmiri dị egwu, site na iji usoro micromachining silicon pụrụ iche a raara nye iji mepụta sensọ ọdịyo.
RGB LED
RGB LED (DL3) bụ ọkụ anode nkịtị nke ejikọrọ na modul Nina W102. Igwe ọkụ na-agbanyụ mgbe ọnọdụ dijitalụ dị elu na mgbe ọnọdụ dijitalụ dị ala.
Osisi Ike
Enwere ike ịkwado njikọ Arduino Nano RP2040 site na ọdụ ụgbọ mmiri Micro USB (J1) ma ọ bụ ọzọ site na VIN na JP2. Ihe ntụgharị buck onboard na-enye 3V3 na microcontroller RP2040 yana akụkụ ndị ọzọ niile. Na mgbakwunye, RP2040 nwekwara ihe nhazi 1V8 dị n'ime.
Ọrụ Board
Mmalite – IDE
Ọ bụrụ na ịchọrọ ịhazi Arduino® Nano RP2040 Jikọọ mgbe ị na-anọghị n'ịntanetị, ịkwesịrị ịwụnye Arduino® IDE Desktop [1] Iji jikọọ njikwa Arduino® Edge na kọmputa gị, ị ga-achọ eriri USB micro. Nke a na-enyekwa ike na osisi ahụ, dị ka LED gosipụtara.
Mmalite – Arduino Web Onye nchịkọta akụkọ
Bọọdụ Arduino® niile, gụnyere nke a, na-arụ ọrụ nke ọma na Arduino® Web Editor [2], site na ịwụnye ngwa mgbakwunye dị mfe.
Arduino® Web A na-akwado onye nchịkọta akụkọ n'ịntanetị, ya mere ọ ga-adị ọhụrụ mgbe niile site na njirimara na nkwado maka bọọdụ niile. Soro [3] ka ịmalite itinye koodu na ihe nchọgharị wee bulite ihe osise gị na bọọdụ gị.
Mmalite – Arduino IoT Cloud
A na-akwado ngwaahịa Arduino® IoT niile na Arduino® IoT Cloud nke na-enye gị ohere ịbanye, eserese na nyochaa data ihe mmetụta, kpalite ihe omume, wee rụzie ụlọ ma ọ bụ azụmahịa gị.
Sampna Sketches
SampEnwere ike ịchọta ihe osise maka Arduino® Nano RP2040 Connect na "Ex".amples” menu na Arduino® IDE ma ọ bụ na ngalaba “Akwụkwọ” nke Arduino websaịtị [4]
Ngwa ntanetị
Ugbu a na ị gafere isi ihe ị nwere ike ime na bọọdụ ị nwere ike ịchọpụta ohere na-adịghị agwụ agwụ ọ na-enye site na ịlele ọrụ na-akpali akpali na ProjectHub [5], Arduino® Library Reference [6] na ụlọ ahịa dị n'ịntanetị [7] ebe. ị ga-enwe ike iji sensọ, actuators na ndị ọzọ mejuo osisi gị.
Iweghachite Board
Bọdụ Arduino niile nwere bootloader arụnyere n'ime ya nke na-enye ohere ịmegharị bọọdụ ahụ site na USB. Ọ bụrụ na eserese kpuchiri ihe nrụpụta na bọọdụ ahụ enweghị ike iru ọzọ site na USB, ọ ga-ekwe omume ịbanye ọnọdụ bootloader site na ịpị bọtịnụ nrụpụta ugboro abụọ ozugbo ọ gbasịrị.
Pinouts njikọ
J1 Micro USB
| Ntụtụ | Ọrụ | Ụdị | Nkọwa |
| 1 | V-BUS | Ike | 5V ike USB |
| 2 | D- | dị iche iche | USB data dị iche iche - |
| 3 | D+ | dị iche iche | USB data dị iche iche + |
| 4 | ID | Dijitalụ | Ejighi ya |
| 5 | GND | Ike | Ala |
JP1
| Ntụtụ | Ọrụ | Ụdị | Nkọwa |
| 1 | TX1 | Dijitalụ | UART TX / Digital Pin 1 |
| 2 | RX0 | Dijitalụ | UART RX / Digital Pin 0 |
| 3 | RST | Dijitalụ | Tọgharia |
| 4 | GND | Ike | Ala |
| 5 | D2 | Dijitalụ | Pin dijitalụ 2 |
| 6 | D3 | Dijitalụ | Pin dijitalụ 3 |
| 7 | D4 | Dijitalụ | Pin dijitalụ 4 |
| 8 | D5 | Dijitalụ | Pin dijitalụ 5 |
| 9 | D6 | Dijitalụ | Pin dijitalụ 6 |
| 10 | D7 | Dijitalụ | Pin dijitalụ 7 |
| 11 | D8 | Dijitalụ | Pin dijitalụ 8 |
| 12 | D9 | Dijitalụ | Pin dijitalụ 9 |
| 13 | D10 | Dijitalụ | Pin dijitalụ 10 |
| 14 | D11 | Dijitalụ | Pin dijitalụ 11 |
| 15 | D12 | Dijitalụ | Pin dijitalụ 12 |
JP2
| Ntụtụ | Ọrụ | Ụdị | Nkọwa |
| 1 | D13 | Dijitalụ | Pin dijitalụ 13 |
| 2 | 3.3V | Ike | 3.3V ike |
| 3 | REF | Analọg | NC |
| 4 | A0 | Analọg | Analog Pin 0 |
| 5 | A1 | Analọg | Analog Pin 1 |
| 6 | A2 | Analọg | Analog Pin 2 |
| 7 | A3 | Analọg | Analog Pin 3 |
| 8 | A4 | Analọg | Analog Pin 4 |
| 9 | A5 | Analọg | Analog Pin 5 |
| 10 | A6 | Analọg | Analog Pin 6 |
| 11 | A7 | Analọg | Analog Pin 7 |
| 12 | VUSB | Ike | Ntinye USB Voltage |
| 13 | REC | Dijitalụ | BOOTSEL |
| 14 | GND | Ike | Ala |
| 15 | VIN | Ike | Voltage Ntinye |
Mara: Akwụkwọ ntụaka analọg voltagA na-edozi ya na +3.3V. Ejikọrọ A0-A3 na ADC RP2040. A4-A7 jikọọ na Nina W102 ADC. Na mgbakwunye, A4 na A5 na-eso ụgbọ ala I2C nke RP2040 na-ekekọrịta ma ejiri 4.7 KΩ resistors dọkpụrụ nke ọ bụla.
RP2040 SWD mpempe akwụkwọ
| Ntụtụ | Ọrụ | Ụdị | Nkọwa |
| 1 | SWDIO | Dijitalụ | SWD Data Line |
| 2 | GND | Dijitalụ | Ala |
| 3 | SWCLK | Dijitalụ | Elekere SWD |
| 4 | + 3V3 | Dijitalụ | + 3V3 ụgbọ okporo ígwè |
| 5 | TP_RESETN | Dijitalụ | Tọgharia |
Nina W102 SWD Pad
| Ntụtụ | Ọrụ | Ụdị | Nkọwa |
| 1 | TP_RST | Dijitalụ | Tọgharia |
| 2 | TP_RX | Dijitalụ | Oghere Usoro Rx |
| 3 | TP_TX | Dijitalụ | Oghere Usoro Tx |
| 4 | TP_GPIO0 | Dijitalụ | GPIO0 |
Ozi igwe
Asambodo
Nkwupụta nke Nkwekọrịta CE DoC (EU)
Anyị na-ekwupụta n'okpuru ọrụ anyị naanị na ngwaahịa ndị dị n'elu kwekọrọ na ihe ndị dị mkpa nke ntuziaka EU na-esote ya mere tozuru oke maka mmegharị n'efu n'ime ahịa nke nwere European Union (EU) na European Economic Area (EEA).
Nkwupụta nke Nkwekọrịta na EU RoHS & REACH 211 01/19/2021
bọọdụ Arduino kwekọrọ na RoHS 2 Directive 2011/65/EU nke European nzuko omeiwu na RoHS 3 Directive 2015/863/EU nke Council of 4 June 2015 na mmachi nke ojiji nke ụfọdụ ize ndụ ihe na ngwa eletriki na eletrọnịkị.
| Ihe | Oke kacha (ppm) |
| Ndu (Pb) | 1000 |
| Ogwugwu (Cd) | 100 |
| Ebere (Hg) | 1000 |
| Chromium Hexavalent (Cr6+) | 1000 |
| Poly Brominated Biphenyls (PBB) | 1000 |
| Poly Brominated Diphenyl ethers (PBDE) | 1000 |
| Bis (2-Ethylhexyl} phthalate (DEHP) | 1000 |
| Benzyl butyl phthalate (BBP) | 1000 |
| Dibutyl phthalate (DBP) | 1000 |
| Diisobutyl phthalate (DIBP) | 1000 |
Exemptions : Enweghị mpụ a na-azọrọ.
Boards Arduino na-akwado nke ọma na ihe ndị metụtara European Union Regulation (EC) 1907/2006 gbasara ndebanye aha, nyocha, ikike na mmachi nke kemịkalụ (REACH). Anyị na-ekwupụta enweghị nke SVHC (https://echa.europa.eu/)web/ guest/candidate-list-table), Ndekọ Candidate nke ihe dị oke mkpa maka ikike nke ECHA wepụtara ugbu a, dị na ngwaahịa niile (yana ngwugwu) n'ọnụọgụ mkpokọta na ntinye nha ma ọ bụ karịa 0.1%. Dị ka ihe ọmụma anyị si mara, anyị na-ekwupụtakwa na ngwaahịa anyị enweghị nke ọ bụla n'ime ihe ndị e depụtara na "Ndepụta ikike" (Annex XIV nke ụkpụrụ REACH) na ihe ndị dị oke nchegbu (SVHC) na oke ọ bụla dị mkpa dị ka akọwapụtara. site na Mgbakwunye XVII nke ndepụta Candidate bipụtara EHA (European Chemical Agency) 1907/2006/EC.
Nkwupụta mineral esemokwu
Dị ka a zuru ụwa ọnụ soplaya nke eletrọnịkị na eletriki components, Arduino maara nke ọrụ anyị n'ihe gbasara iwu na ụkpụrụ gbasara Conflict Minerals, kpọmkwem Dodd Frank Wall Street Reform and Consumer Protection Act, Nkebi 1502. Arduino adịghị kpọmkwem isi mmalite ma ọ bụ hazie esemokwu mineral. dị ka Tin, Tantalum, Tungsten, ma ọ bụ ọla edo. Mineral esemokwu dị na ngwaahịa anyị n'ụdị solder, ma ọ bụ dị ka akụkụ na alloys metal. Dịka akụkụ nke mbọ anyị kwesịrị ekwesị Arduino akpọtụrụla ndị na-ebubata akụrụngwa n'ime ụdọ ọkọnọ anyị iji chọpụta na ha nọgidere na-agbaso ụkpụrụ ahụ. Dabere na ozi enwetara ugbu a, anyị na-ekwupụta na ngwaahịa anyị nwere mineral na-akpata esemokwu sitere na mpaghara enweghị esemokwu.
FCC ịkpachara anya
Mgbanwe ọ bụla ma ọ bụ mgbanwe ọ bụla nke ndị na-ahụ maka nnabata na-akwadoghị nke ọma nwere ike imebi ikike onye ọrụ iji rụọ ọrụ ahụ.
Ngwaọrụ a na-akwado akụkụ 15 nke Iwu FCC. A na-arụ ọrụ n'okpuru ọnọdụ abụọ a:
- Ngwaọrụ a nwere ike ọ gaghị ebute nnyonye anya na-emerụ ahụ
- Ngwaọrụ a ga-anabatarịrị nnyonye anya ọ bụla enwetara, gụnyere nnyonye anya nwere ike ibute ọrụ na-achọghị.
Nkwupụta Mkpughe Radiation FCC RF:
- Agaghị ejikọta ihe nnyefe a ma ọ bụ na-arụ ọrụ na njikọ antenna ma ọ bụ nnyefe ọ bụla ọzọ.
- Ngwa a na-akwado oke mkpughe radieshon RF ewepụtara maka gburugburu enweghị njikwa.
- Ekwesịrị ịwụnye akụrụngwa a ma rụọ ọrụ ya na anya kacha nta 20cm n'etiti radiator & ahụ gị.
Akwụkwọ ntuziaka onye ọrụ maka ngwa redio enweghị ikike ga-enwe ọkwa ndị a ma ọ bụ nha nhata na ọnọdụ pụtara ìhè n'ime akwụkwọ ntuziaka onye ọrụ ma ọ bụ ọzọ na ngwaọrụ ma ọ bụ ha abụọ. Ngwaọrụ a na-akwado ụlọ ọrụ mmepụta ihe
Ọkọlọtọ RSS enweghị ikike Canada. A na-arụ ọrụ n'okpuru ọnọdụ abụọ a:
- ngwaọrụ a nwere ike ọ gaghị ebute nnyonye anya
- Ngwaọrụ a ga-anabatarịrị nnyonye anya ọ bụla, gụnyere nnyonye anya nwere ike bute ọrụ ngwaọrụ ahụ achọghị.
Ịdọ aka ná ntị IC SAR:
Ekwesịrị ịwụnye akụrụngwa a ma rụọ ọrụ ya na anya kacha nta 20 cm n'etiti radiator na ahụ gị.
Ihe dị mkpa: Ọnọdụ okpomọkụ nke EUT enweghị ike ịgafe 80 ℃ ma ghara ịdị ala karịa -20 ℃.
Site na nke a, Arduino Srl na-ekwupụta na ngwaahịa a kwekọrọ na ihe ndị dị mkpa chọrọ yana ndokwa ndị ọzọ dị mkpa nke Ntuziaka 2014/53/EU. Ekwenyere ka ejiri ngwaahịa a na mba ndị otu EU niile.
| Ugboro ugboro | Ike Isotropic Radiated Ike kacha arụ ọrụ (EIRP) |
| TBC | TBC |
Ozi ụlọ ọrụ
| Aha Ụlọ Ọrụ | Arduino Srl |
| Adreesị ụlọ ọrụ | Site Ferruccio Pelli 14, 6900 Lugano, TI (Ticino), Switzerland |
Akwụkwọ ntụaka
| Ref | Njikọ |
| Arduino IDE (Desktọpụ) | https://www.arduino.cc/en/Main/Software |
| Arduino IDE (igwe ojii) | https://create.arduino.cc/editor |
| Cloud IDE na-amalite | https://create.arduino.cc/projecthub/Arduino_Genuino/getting-started-with- arduino-web-editor-4b3e4a |
| Arduino Websaịtị | https://www.arduino.cc/ |
| Hub Project | https://create.arduino.cc/projecthub?by=part&part_id=11332&sort=trending |
| PDM (igwe okwu) Library | https://www.arduino.cc/en/Reference/PDM |
| WiFiNINA (Wi-Fi, W102) ọba akwụkwọ | https://www.arduino.cc/en/Reference/WiFiNINA |
| ArduinoBLE (Bluetooth®, W- 102) Ọbá akwụkwọ | https://www.arduino.cc/en/Reference/ArduinoBLE |
| Ụlọ akwụkwọ IMU | https://www.arduino.cc/en/Reference/Arduino_LSM6DS3 |
| Ụlọ ahịa dị n'ịntanetị | https://store.arduino.cc/ |
Akụkọ ngbanwe
| Ụbọchị | Ndozigharị | Mgbanwe |
| 02/12/2021 | 2 | Mgbanwe arịọrọ maka asambodo |
| 14/05/2020 | 1 | Mwepụta mbụ |
Akwụkwọ / akụrụngwa
 |
ARDUINO ABX00053 Nano RP2040 Jikọọ na nkụnye eji isi mee [pdf] Akwụkwọ ntuziaka onye ọrụ ABX00053, Nano RP2040 Jikọọ na nkụnye eji isi mee, ABX00053 Nano RP2040 Jikọọ na nkụnye eji isi mee |
 |
ARDUINO ABX00053 Nano RP2040 Jikọọ na nkụnye eji isi mee [pdf] Akwụkwọ ntuziaka onye ọrụ ABX00053, Nano RP2040 Jikọọ na nkụnye eji isi mee, ABX00053 Nano RP2040 Jikọọ na nkụnye eji isi mee |
 |
ARDUINO ABX00053 Nano RP2040 Jikọọ na nkụnye eji isi mee [pdf] Akwụkwọ ntuziaka onye ọrụ ABX00053, Nano RP2040 Jikọọ na nkụnye eji isi mee |
 |
ARDUINO ABX00053 Nano RP2040 Jikọọ [pdf] Akwụkwọ ntuziaka onye ọrụ ABX00053, Nano RP2040 Jikọọ |
 |
ARDUINO ABX00053 Nano RP2040 Jikọọ na nkụnye eji isi mee [pdf] Akwụkwọ ntuziaka onye nwe ABX00053, Nano RP2040 Jikọọ na nkụnye eji isi mee, ABX00053 Nano RP2040 Jikọọ na nkụnye eji isi mee |
 |
ARDUINO ABX00053 Nano RP2040 Jikọọ [pdf] Akwụkwọ ntuziaka onye ọrụ ABX00053, Nano RP2040 Jikọọ |
 |
ARDUINO ABX00053 Nano RP2040 Jikọọ na nkụnye eji isi mee [pdf] Akwụkwọ ntuziaka onye ọrụ ABX00053, Nano RP2040 Jikọọ na nkụnye eji isi mee, ABX00053 Nano RP2040 Jikọọ na nkụnye eji isi mee |
 |
ARDUINO ABX00053 Nano RP2040 Jikọọ na nkụnye eji isi mee [pdf] Akwụkwọ ntuziaka onye ọrụ ABX00053, Nano RP2040 Jikọọ na nkụnye eji isi mee, ABX00053 Nano RP2040 Jikọọ na nkụnye eji isi mee |
