ARDUINO ABX00053 Nano RP2040 Hokela le Bukana ea Mosebelisi ea Lihlooho
Tlhaloso
Karolo e pakiloeng ea Arduino® Nano RP2040 Connect e tlisa Raspberry Pi RP2040 microcontroller e ncha ho Nano form factor. Sebelisa hamolemo lidual 32-bit Arm® Cortex®-M0+ ho etsa liprojeke tsa Inthanete ea Lintho ka khokahanyo ea Bluetooth® le Wi-Fi ka lebaka la mojule oa U-blox® Nina W102. Ikakhele ka setotsoana mererong ea 'nete ea lefats'e ka accelerometer ea onboard, gyroscope, RGB LED le maekerofounu. Theha litharollo tse kenelletseng tsa AI ka boikitlaetso bo fokolang u sebelisa Arduino® Nano RP2040 Connect!
Libaka tse reriloeng
Marang-rang a Lintho (IoT), ho ithuta ka mochini, prototyping,
Likaroloana
Raspberry Pi RP2040 Microcontroller
- 133MHz 32bit Dual Core Arm® Cortex®-M0+
- 264kB ho-chip SRAM
- Selaoli sa Direct Memory Access (DMA).
- Ts'ehetso ea ho fihla ho 16MB ea memori ea Flash ea off-chip ka bese e inehetseng ea QSPI
- Selaoli sa USB 1.1 le PHY, se nang le moamoheli le tšehetso ea sesebelisoa
- 8 Mechini ea mmuso ea PIO
- Programmable IO (PIO) bakeng sa tšehetso e atolositsoeng ea peripheral
- 4 channel ADC e nang le sensor ea mocheso oa ka hare, 0.5 MSa / s, phetoho ea 12-bit
- SWD Debugging
- 2 on-chip PLL ho hlahisa USB le oache ea mantlha
- 40nm process node
- Tšehetso ea mekhoa e mengata e fokolang ea matla
- USB 1.1 Moamoheli / Sesebelisoa
- Vol. Ea kaharetage Regulator ho fana ka core voltage
- Bese e Hatetseng Pele ea Ts'ebetso e Phahameng (AHB)/Advanced Peripheral Bese (APB)
U-blox® Nina W102 Wi-Fi/Bluetooth® Mojule
- 240MHz 32bit Dual Core Xtensa LX6
- 520kB ho-chip SRAM
- 448 Kbyte ROM bakeng sa ho qala le mesebetsi ea mantlha
- 16 Mbit FLASH bakeng sa polokelo ea khoutu ho kenyelletsa encryption ea hardware ho sireletsa mananeo le data
- 1 kbit EFUSE (memori e ke keng ea hlakoloa) bakeng sa liaterese tsa MAC, tlhophiso ea module, Flash-Encryption, le Chip-ID
- IEEE 802.11b/g/n single-band 2.4 GHz Wi-Fi tshebetso
- Bluetooth® 4.2
- Antenna e Kopantsoeng ea Planar Inverted-F (PIFA)
- 4x 12-bit ADC
- 3x I2C, SDIO, CAN, QSPI
Mohopolo
- AT25SF128A 16MB NOR Flash
- Sekhahla sa phetisetso ea data ea QSPI ho fihla ho 532Mbps
- 100K lenaneo / hlakola lipotoloho
ST LSM6DSOXTR 6-axis IMU
- 3D Gyroscope
- ± 2/±4/±8/±16 g sekala se felletseng
- 3D Accelerometer
- ±125/±250/±500/±1000/±2000 dps sekala se felletseng
- Pedometer e tsoetseng pele, detector ea mehato le step counter
- Ho lemoha Motsamao o Bohlokoa, Ho lemoha ha Tilt
- Litšitiso tse tloaelehileng: ho oa mahala, ho tsoha, mokhoa oa 6D/4D, tobetsa le ho penya habeli
- Mochini o ka lokisoang oa boemo bo lekanyelitsoeng: accelerometer, gyroscope le li-sensor tsa kantle
- Mochine oa ho Ithuta oa Mochine
- Sensor e kentsoeng ea mocheso
ST MP34DT06JTR MEMS Microphone
- AOP = 122.5 dBSPL
- 64 dB karo-karolelano ea lerata-ho-lerata
- Omnidirectional sensitivity
- -26 dBFS ± 1 dB kutlo
RGB LED
- Anode e Tloaelehileng
- E hokahane le U-blox® Nina W102 GPIO
Microchip® ATECC608A Crypto
- Cryptographic Co-Processor e nang le Polokelo e Sireletsehileng e thehiloeng ho Hardware
- I2C, SWI
- Tšehetso ea Hardware bakeng sa Symmetric Algorithms:
- SHA-256 & HMAC Hash e kenyeletsang off-chip context boloka/tsosolosa
- AES-128: Encrypt/Decrypt, Galois Field Atisa bakeng sa GCM
- Jenereithara ya ka Hare ya Boleng bo Phahameng NIST SP 800-90A/B/C Random Number Generator (RNG)
- Tšehetso e sireletsehileng ea Boot:
- Netefatso e felletseng ea tshaeno ea khoutu ea ECDSA, digest/saeno e bolokiloeng ka boikhethelo
- Ho tima senotlolo sa puisano ka boikhethelo pele o qala bootle
- Encryption/ Netefatso bakeng sa melaetsa ea ho thibela litlhaselo tsa boto
I/O
- 14x Digital Pin
- 8x Pin ea Analog
- Micro USB
- Tšehetso ea UART, SPI, I2C
Matla
- Buck step-down converter
Boitsebiso ba Tšireletseho
- Sehlopha sa A
Boto
Kopo Examples
Arduino® Nano RP2040 Connect e ka ikamahanya le maemo a fapaneng a ts'ebeliso ka lebaka la microprocessor e matla, li-sensor tsa onboard le Nano form factor. Lisebelisoa tse ka bang teng li kenyelletsa:
Edge Computing: Sebelisa microprocessor e potlakileng le e phahameng ea RAM ho tsamaisa TinyML bakeng sa ho lemoha ka mokhoa o sa tloaelehang, ho lemoha ho khohlela, tlhahlobo ea boitšisinyo le tse ling.
Lisebelisoa tse Apareloang: Sebaka se senyenyane sa Nano footprint se fana ka monyetla oa ho fana ka thuto ea mochine ho lisebelisoa tse ngata tse ka aparoang tse kenyelletsang lipapali tsa lipapali le balaoli ba VR.
Mothusi oa lentsoe: Arduino® Nano RP2040 Connect e kenyelletsa maekrofounu ea omnidirectional e ka sebetsang e le mothusi oa hau oa dijithale mme e nolofalletsa taolo ea lentsoe bakeng sa merero ea hau.
Lisebelisoa
- Cable ea Micro USB
- Lihlooho tsa banna tse 15-pin 2.54mm
- 15-pin 2.54mm lihlooho tsa stackable
Lihlahisoa tse Amanang
Matla a khoheli: Nano I/O Shield
Lintlha
Maemo a Tšebetso a khothalelitsoeng
| Letšoao | Tlhaloso | Min | Tlanya | Max | Yuniti |
| VIN | Keletso voltage ho tloha VIN pad | 4 | 5 | 20 | V |
| VUSB | Keletso voltage ho tsoa ho sehokelo sa USB | 4.75 | 5 | 5.25 | V |
| V3V3 | 3.3V tlhahiso ho ts'ebeliso ea mosebelisi | 3.25 | 3.3 | 3.35 | V |
| I3V3 | 3.3V sephetho sa hajoale (ho kenyeletsoa le IC ea onboard) | – | – | 800 | mA |
| VIH | Kenyeletso ea boemo bo holimo voltage | 2.31 | – | 3.3 | V |
| VIL | Kenyelletso ea boemo bo tlasetage | 0 | – | 0.99 | V |
| IOH Max | Hajoale ho VDD-0.4 V, tlhahiso e behiloe holimo | 8 | mA | ||
| IOL Max | Hajoale ho VSS + 0.4 V, tlhahiso e behiloe tlase | 8 | mA | ||
| VOH | Palo e phahameng voltage, 8mA | 2.7 | – | 3.3 | V |
| TLHOKOMELO | Sephetho se tlase voltage, 8mA | 0 | – | 0.4 | V |
| HLOMPHO | Mocheso oa ho sebetsa | -20 | – | 80 | °C |
Tšebeliso ea Matla
| Letšoao | Tlhaloso | Min | Tlanya | Max | Yuniti |
| PBL | Tšebeliso ea matla e nang le loop e phathahaneng | TBC | mW | ||
| PLP | Tšebeliso ea matla ka mokhoa o fokolang oa matla | TBC | mW | ||
| PMAX | Tšebeliso e Felletseng ea Matla | TBC | mW |
E sebetsa hapeview
Setšoantšo se Thibeloang
Board Topology
Pele View
| Ref. | Tlhaloso | Ref. | Tlhaloso |
| U1 | Raspberry Pi RP2040 Microcontroller | U2 | Ublox NINA-W102-00B Wi-Fi/Bluetooth® Mojule |
| U3 | N/A | U4 | Tlhaloso: ATECC608A-MAHDA-T Crypto IC |
| U5 | AT25SF128A-MHB-T 16MB Flash IC | U6 | MP2322GQH Taolo ea Bohato-Down Buck |
| U7 | DSC6111HI2B-012.0000 MEMS Oscillator | U8 | MP34DT06JTR MEMS Omnidirectional Microphone IC |
| U9 | LSM6DSOXTR 6-axis IMU e nang le Core Learning Core | J1 | Sehokelo sa Male Micro USB |
| DL1 | Matla a Tala ho LED | DL2 | LED e hahiloeng ka Orange |
| DL3 | RGB Common Anode LED | PB1 | Seta Botjha Konopo |
| JP2 | Analog Pin + D13 Pins | JP3 | Digital Pins |
Morao View
| Ref. | Tlhaloso | Ref. | Tlhaloso |
| SJ4 | 3.3V jumper (e hokahane) | SJ1 | VUSB jumper (e khaotsoe) |
processor
Motlakase o thehiloe holim'a silicon e ncha ea Raspberry Pi RP2040 (U1). Microcontroller ena e fana ka menyetla ea nts'etsopele ea Marang-rang a Lintho (IoT) a matla a tlase le ho ithuta ka mochini. Li-symmetric Arm® Cortex®-M0+ tse peli tse ts'oaretsoeng ka 133MHz li fana ka matla a khomphutha bakeng sa ho ithuta ka mochini o kentsoeng le ts'ebetso e ts'oanang e sebelisang matla a tlase. Ho fanoe ka libanka tse tšeletseng tse ikemetseng tsa 264 KB SRAM le 2MB. Ho fihlella memori ka kotloloho ho fana ka khokahano e potlakileng lipakeng tsa li-processor le memori e ka etsoang hore e se sebetse hammoho le mantlha ho kenya boemo ba boroko. Serial wire debug (SWD) e fumaneha ho tloha boot ka liphahlo tse tlas'a boto. RP2040 e matha ho 3.3V mme e na le matla a ka haretage regulator e fanang ka 1.1V.
RP2040 e laola peripherals le li-pin tsa digital, hammoho le li-analog pins (A0-A3). Likhokahano tsa I2C ho li-pins A4 (SDA) le A5 (SCL) li sebelisoa bakeng sa ho hokela li-peripherals tse ka har'a sekepe 'me li huleloa ka sehanyetsi sa 4.7 kΩ. SWD Clock line (SWCLK) le ho seta bocha li boetse li huleloa ka sehanyetsi sa 4.7 kΩ. Oscillator ea kantle ea MEMS (U7) e sebetsang ka 12MHz e fana ka lebelo la oache. IO e hlophisitsoeng e thusa ho kenya tšebetsong protocol ea puisano e sa reroang e nang le moroalo o fokolang ho li-cores tsa mantlha tsa ts'ebetso. Sehokelo sa sesebelisoa sa USB 1.1 se kengoa tšebetsong ho RP2040 bakeng sa ho kenya khoutu.
Khokahano ea Wi-Fi/Bluetooth®
Khokahano ea Wi-Fi le Bluetooth® e fanoa ke mojule oa Nina W102 (U2). RP2040 e na le lithakhisa tse 4 feela tsa analoge, 'me Nina e sebelisetsoa ho atolosa hoo ho fihla ho tse robeli ka ho feletseng joalokaha ho tloaelehile ho Arduino Nano form factor ka lisebelisoa tse ling tsa 4 12-bit analog (A4-A7). Ho feta moo, anode e tloaelehileng ea RGB LED e boetse e laoloa ke module ea Nina W-102 hoo LED e timang ha boemo ba digital bo le HIGH le ha boemo ba digital bo le LOW. Antenna ea ka hare ea PCB ka har'a mojule e felisa tlhoko ea lenaka la kantle. Module ea Nina W102 e boetse e kenyelletsa "dual core Xtensa LX6 CPU" eo hape e ka hlophisoang ntle le RP2040 ka liphahlo tse ka tlas'a boto e sebelisang SWD.
6-axis IMU
Hoa khoneha ho fumana lintlha tsa 3D gyroscope le 3D accelerometer data ho tloha ho LSM6DSOX 6-axis IMU (U9). Ntle le ho fana ka lintlha tse joalo, hoa khoneha ho ithuta ka mochini ho IMU bakeng sa ho lemoha boitšisinyo.
Mehopolo ea kantle
RP2040 (U1) e na le phihlello ea memori e eketsehileng ea 16 MB ka sebopeho sa QSPI. Karolo ea execute-in-place (XIP) ea RP2040 e lumella memori ea flash e kantle hore e rarolloe le ho fihleloa ke sistimi joalo ka ha eka ke mohopolo o ka hare, ntle le ho qala ho kopitsa khoutu mohopolong oa kahare.
Mokhoa oa ho ngola
ATECC608A Cryptographic IC (U4) e fana ka bokhoni bo sireletsehileng ba boot hammoho le SHA le AES-128 ts'ehetso ea encryption / decryption bakeng sa ts'ireletso lits'ebetsong tsa Smart Home le Industrial IoT (IIoT). Ntle le moo, jenereithara ea linomoro e sa sebetseng e fumaneha hape hore e sebelisoe ke RP2040.
Microphone
Maekerofounu ea MP34DT06J e hokahantsoe ka sebopeho sa PDM ho RP2040. Maekerofounu ea MEMS ea dijithale e ea hohle 'me e sebetsa ka capacitive sensing element e nang le lets'oao le phahameng (64 dB) ho tekanyo ea lerata. Ntho ea kutlo, e khonang ho bona maqhubu a acoustic, e etsoa ka mokhoa o ikhethileng oa silicon micromachining o ikemiselitseng ho hlahisa li-audio sensors.
RGB LED
RGB LED (DL3) ke LED e tloaelehileng ea anode e kopantsoeng le mojule oa Nina W102. LED e tima ha boemo ba digital bo le HIGH le ha boemo ba digital bo le LOW.
Sefate sa Matla
Arduino Nano RP2040 Connect e ka tsamaisoa ke Micro USB port (J1) kapa ka tsela e 'ngoe ka VIN ho JP2. Sesebelisoa sa onboard buck converter se fana ka 3V3 ho microcontroller ea RP2040 le lisebelisoa tse ling kaofela. Ntle le moo, RP2040 e boetse e na le molaoli oa kahare oa 1V8.
Ts'ebetso ea Boto
Ho qala - IDE
Haeba u batla ho hlophisa Arduino® Nano RP2040 Connect ha u ntse u le sieo inthaneteng, u lokela ho kenya Arduino® Desktop IDE [1] Ho hokela taolo ea Arduino® Edge komporong ea hau, u tla hloka thapo e nyane ea USB. Sena se boetse se fana ka matla ho boto, joalokaha ho bontšitsoe ke LED.
Ho qala - Arduino Web Mohlophisi
Liboto tsohle tsa Arduino®, ho kenyeletsoa le ena, li sebetsa ka ntle ho lebokose la Arduino® Web Mohlophisi [2], ka ho kenya plugin e bonolo feela.
Arduino® Web Editor e tšoaroa inthaneteng, ka hona e tla lula e le morao-rao ka likarolo tsa morao-rao le tšehetso bakeng sa liboto tsohle. Latela [3] ho qala ho kenya likhoutu ho sebatli le ho kenya litšoantšo tsa hau botong ea hau.
Ho qala - Arduino IoT Cloud
Lihlahisoa tsohle tse nolofalitsoeng tsa Arduino® IoT li tšehetsoa ho Arduino® IoT Cloud e u lumellang hore u kene, u kenye le ho sekaseka lintlha tsa sensor, ho qala liketsahalo, le ho iketsetsa ntlo kapa khoebo ea hau.
Sample Sketches
Sample litšoantšo tsa Arduino® Nano RP2040 Connect li ka fumanoa ho "Ex.amples" ho Arduino® IDE kapa karolong ea "Documentation" ea Arduino websebaka [4]
Lisebelisoa tsa Marang-rang
Kaha joale u se u fetile linthong tsa motheo tsa seo u ka se etsang ka boto u ka hlahloba menyetla e sa feleng eo e fanang ka eona ka ho hlahloba merero e thabisang ho ProjectHub [5], Arduino® Library Reference [6] le lebenkele la marang-rang [7] moo o tla khona ho tlatselletsa boto ea hau ka li-sensor, li-actuator le tse ling.
Boto ea Pholiso
Liboto tsohle tsa Arduino li na le bootloader e hahelletsoeng ka hare e lumellang ho bonesa boto ka USB. Haeba sketch e notlela processor mme boto ha e sa fumaneha ka USB, hoa khonahala ho kenya mokhoa oa bootloader ka ho tlanya konopo ea reset hang ka mor'a ho tima.
Sehokedi Pinouts
J1 USB e nyenyane
| Pin | Mosebetsi | Mofuta | Tlhaloso |
| 1 | V-BUS | Matla | Matla a 5V a USB |
| 2 | D- | Tse fapaneng | Lintlha tse fapaneng tsa USB - |
| 3 | D+ | Tse fapaneng | Lintlha tse fapaneng tsa USB + |
| 4 | ID | Dijithale | E sa sebelisoeng |
| 5 | GND | Matla | Fatše |
JP1
| Pin | Mosebetsi | Mofuta | Tlhaloso |
| 1 | TX1 | Dijithale | UART TX / Digital Pin 1 |
| 2 | RX0 | Dijithale | UART RX / Digital Pin 0 |
| 3 | RST | Dijithale | Seta bocha |
| 4 | GND | Matla | Fatše |
| 5 | D2 | Dijithale | Digital Pin 2 |
| 6 | D3 | Dijithale | Digital Pin 3 |
| 7 | D4 | Dijithale | Digital Pin 4 |
| 8 | D5 | Dijithale | Digital Pin 5 |
| 9 | D6 | Dijithale | Digital Pin 6 |
| 10 | D7 | Dijithale | Digital Pin 7 |
| 11 | D8 | Dijithale | Digital Pin 8 |
| 12 | D9 | Dijithale | Digital Pin 9 |
| 13 | D10 | Dijithale | Digital Pin 10 |
| 14 | D11 | Dijithale | Digital Pin 11 |
| 15 | D12 | Dijithale | Digital Pin 12 |
JP2
| Pin | Mosebetsi | Mofuta | Tlhaloso |
| 1 | D13 | Dijithale | Digital Pin 13 |
| 2 | 3.3V | Matla | Matla a 3.3V |
| 3 | REF | Analoge | NC |
| 4 | A0 | Analoge | Analog Pin 0 |
| 5 | A1 | Analoge | Analog Pin 1 |
| 6 | A2 | Analoge | Analog Pin 2 |
| 7 | A3 | Analoge | Analog Pin 3 |
| 8 | A4 | Analoge | Analog Pin 4 |
| 9 | A5 | Analoge | Analog Pin 5 |
| 10 | A6 | Analoge | Analog Pin 6 |
| 11 | A7 | Analoge | Analog Pin 7 |
| 12 | VUSB | Matla | Keletso ea USB Voltage |
| 13 | REC | Dijithale | BOOTSELE |
| 14 | GND | Matla | Fatše |
| 15 | VIN | Matla | MoqtagKeletso |
Hlokomela: Referense ea analoge voltage e tsitsitseng ho +3.3V. A0-A3 e hokahane le ADC ea RP2040. A4-A7 e hokahane le Nina W102 ADC. Ho feta moo, A4 le A5 li arolelanoa le bese ea I2C ea RP2040 'me e' ngoe le e 'ngoe e huloa ka lihanyetsi tse 4.7 KΩ.
RP2040 SWD Pad
| Pin | Mosebetsi | Mofuta | Tlhaloso |
| 1 | SWDIO | Dijithale | Mohala oa data oa SWD |
| 2 | GND | Dijithale | Fatše |
| 3 | SWCLK | Dijithale | Oache ea SWD |
| 4 | +3V3 | Dijithale | +3V3 Seporo sa Matla |
| 5 | TP_RESETN | Dijithale | Seta bocha |
Sebaka sa marang-rang sa Nina W102 SWD Pad
| Pin | Mosebetsi | Mofuta | Tlhaloso |
| 1 | TP_RST | Dijithale | Seta bocha |
| 2 | TP_RX | Dijithale | Setšoantšo sa Rx |
| 3 | TP_TX | Dijithale | Lethathamo la Tx |
| 4 | TP_GPIO0 | Dijithale | GPIO0 |
Boitsebiso ba Mechini
Setifikeiti
Declaration of Conformity CE DoC (EU)
Re phatlalatsa tlas'a boikarabelo ba rona hore lihlahisoa tse ka holimo li lumellana le litlhoko tsa bohlokoa tsa Litaelo tse latelang tsa EU 'me kahoo re tšoaneleha bakeng sa ho tsamaea ka bolokolohi ka har'a limmaraka tse kenyeletsang European Union (EU) le European Economic Area (EEA).
Phatlalatso ea Tumellano le EU RoHS & REACH 211 01/19/2021
Liboto tsa Arduino li lumellana le RoHS 2 Directive 2011/65/EU ea Paramente ea Europe le RoHS 3 Directive 2015/863/EU ea Lekhotla la 4 Phuptjane 2015 mabapi le thibelo ea tšebeliso ea lintho tse ling tse kotsi ho lisebelisoa tsa motlakase le tsa elektroniki.
| Ntho | Maximum Limit (ppm) |
| Lebisa (Pb) | 1000 |
| Cadmium (Cd) | 100 |
| Motsoako (Hg) | 1000 |
| Hexavalent Chromium (Cr6+) | 1000 |
| Poly Brominated Biphenyls (PBB) | 1000 |
| Poly Brominated Diphenyl ethers (PBDE) | 1000 |
| Bis(2-Ethylhexyl} phthalate (DEHP) | 1000 |
| Benzyl butyl phthalate (BBP) | 1000 |
| Dibutyl phthalate (DBP) | 1000 |
| Diisobutyl phthalate (DIBP) | 1000 |
Litokoloho : Ha ho litokollo tse batloang.
Arduino Boards e lumellana ka botlalo le litlhoko tse amanang le European Union Regulation (EC) 1907 /2006 mabapi le Ngoliso, Tlhahlobo, Tumello le Thibelo ea Lik'hemik'hale (REACH). Ha re phatlalatse leha e le efe ea SVHCs (https://echa.europa.eu/web/moeti/lethathamo la moeti), Lethathamo la Bakhethoa ba Matšoenyeho a Phahameng ka ho Fetisisa bakeng sa tumello e lokollotsoeng hajoale ke ECHA, le teng lihlahisoa tsohle (le sephutheloana) ka bongata bo lekanang le mahloriso a lekanang kapa a ka holimo ho 0.1%. Ho latela tsebo ea rona, re boetse re phatlalatsa hore lihlahisoa tsa rona ha li na letho la lintho tse thathamisitsoeng ho "Authorization List" (Annex XIV ea melaoana ea REACH) le Substances of Very High Concern (SVHC) ka chelete efe kapa efe ea bohlokoa joalo ka ha ho boletsoe. ka Sehlomathiso sa XVII sa Lethathamo la Bakhethoa le hatisitsoeng ke ECHA (European Chemical Agency) 1907 /2006/EC.
Phatlalatso ea Liminerale tsa Khohlano
Joaloka mofani oa lefats'e oa likarolo tsa elektronike le motlakase, Arduino e tseba boitlamo ba rona mabapi le melao le melaoana e mabapi le Conflict Minerals, haholo-holo Dodd Frank Wall Street Reform le Consumer Protection Act, Karolo ea 1502. Arduino ha e fane ka ho toba kapa ha e sebetsane le liminerale tsa likhohlano joalo ka Tin, Tantalum, Tungsten, kapa Khauta. Liminerale tsa likhohlano li fumaneha lihlahisoa tsa rona ka mokhoa oa solder, kapa e le karolo ea li-alloys tsa tšepe. E le karolo ea boitelo ba rona bo loketseng, Arduino e ikopanye le bafani ba thepa ka har'a ketane ea rona ea phepelo ho netefatsa hore ba tsoela pele ho latela melaoana. Ho latela lintlha tse fumanoeng ho tla fihlela joale, re phatlalatsa hore lihlahisoa tsa rona li na le Liminerale tsa Likhohlano tse tsoang libakeng tse se nang likhohlano.
FCC Tlhokomeliso
Liphetoho life kapa life tse sa amoheloeng ka kotloloho ke mokha o ikarabellang bakeng sa tumellano li ka hlakola matla a mosebelisi a ho sebelisa sesebelisoa.
Sesebelisoa sena se lumellana le karolo ea 15 ea Melao ea FCC. Ts'ebetso e ipapisitse le maemo a mabeli a latelang:
- Sesebelisoa sena se ka 'na sa se ke sa baka tšitiso e kotsi
- sesebelisoa sena se tlameha ho amohela tšitiso efe kapa efe e amohetsoeng, ho kenyeletsoa tšitiso e ka bakang ts'ebetso e sa batleheng.
Polelo ea Ts'oaetso ea Mahlaseli a FCC RF:
- Transmitter ena ha ea lokela ho ba sebakeng se le seng kapa ho sebetsa mmoho le antenna efe kapa efe kapa transmitter.
- Sesebelisoa sena se lumellana le meeli ea ho pepeseha ha mahlaseli a RF e behiloeng bakeng sa tikoloho e sa laoleheng.
- Thepa ena e lokela ho kengoa le ho sebetsoa ka sebaka sa bonyane 20cm lipakeng tsa radiator le 'mele oa hau.
Litaelo tsa mosebelisi bakeng sa lisebelisoa tsa seea-le-moea tse sa lumelloeng ke laesense li tla ba le tsebiso e latelang kapa e ts'oanang le eona sebakeng se hlakileng bukeng ea mosebelisi kapa sesebelisoa kapa ka bobeli. Sesebelisoa sena se lumellana le Indasteri
Maemo a RSS a sa tsoeng laesenseng ea Canada. Ts'ebetso e ipapisitse le maemo a mabeli a latelang:
- sesebelisoa sena se ka 'na sa se ke sa baka tšitiso
- sesebelisoa sena se tlameha ho amohela tšitiso efe kapa efe, ho kenyeletsoa tšitiso e ka bakang ts'ebetso e sa batleheng ea sesebelisoa.
Tlhokomeliso ea IC SAR:
Thepa ena e lokela ho kenngoa le ho sebetsoa ka sebaka se ka tlase ho 20 cm pakeng tsa radiator le 'mele oa hau.
Bohlokoa: Thempereichara ea ts'ebetso ea EUT e ke ke ea feta 80 ℃ mme ha ea lokela ho ba ka tlase ho -20 ℃.
Ka hona, Arduino Srl e phatlalatsa hore sehlahisoa sena se lumellana le litlhoko tsa bohlokoa le lipehelo tse ling tse amehang tsa Directive 2014/53/EU. Sehlahisoa sena se lumelletsoe ho sebelisoa linaheng tsohle tsa litho tsa EU.
| Maqhubu a maqhubu | Maximum Effective Isotropic Radiated Power (EIRP) |
| TBC | TBC |
Lintlha tsa Khampani
| Lebitso la K'hamphani | Arduino Srl |
| Aterese ea Khampani | Via Ferruccio Pelli 14, 6900 Lugano, TI (Ticino), Switzerland |
Litokomane Tsa Litšupiso
| Ref | Sehokelo |
| Arduino IDE (Desktop) | https://www.arduino.cc/en/Main/Software |
| Arduino IDE (Leru) | https://create.arduino.cc/editor |
| Cloud IDE Ho qala | https://create.arduino.cc/projecthub/Arduino_Genuino/getting-started-with- arduino-web-editor-4b3e4a |
| Arduino Websebaka | https://www.arduino.cc/ |
| Morero Hub | https://create.arduino.cc/projecthub?by=part&part_id=11332&sort=trending |
| PDM (maekerofounu) Library | https://www.arduino.cc/en/Reference/PDM |
| WiFiNINA (Wi-Fi, W102) Laeborari | https://www.arduino.cc/en/Reference/WiFiNINA |
| ArduinoBLE (Bluetooth®, W- 102) Library | https://www.arduino.cc/en/Reference/ArduinoBLE |
| Laeborari ea IMU | https://www.arduino.cc/en/Reference/Arduino_LSM6DS3 |
| Online Store | https://store.arduino.cc/ |
Nalane ea Phetoho
| Letsatsi | Khatiso | Liphetoho |
| 02/12/2021 | 2 | Liphetoho tse kopiloeng bakeng sa setifikeiti |
| 14/05/2020 | 1 | Phatlalatso ea Pele |
Litokomane / Lisebelisoa
 |
ARDUINO ABX00053 Nano RP2040 Hokela le Lihlooho [pdf] Bukana ea Mosebelisi ABX00053, Nano RP2040 Hokela le Lihlooho, ABX00053 Nano RP2040 Hokela le Lihlooho |
 |
ARDUINO ABX00053 Nano RP2040 Hokela le Lihlooho [pdf] Bukana ea Mosebelisi ABX00053, Nano RP2040 Hokela le Lihlooho, ABX00053 Nano RP2040 Hokela le Lihlooho |
 |
ARDUINO ABX00053 Nano RP2040 Hokela le Lihlooho [pdf] Bukana ea Mosebelisi ABX00053, Nano RP2040 Hokela le Lihlooho |
 |
ARDUINO ABX00053 Nano RP2040 Connect [pdf] Bukana ea Mosebelisi ABX00053, Nano RP2040 Connect |
 |
ARDUINO ABX00053 Nano RP2040 Hokela le Lihlooho [pdf] Buka ea Mong'a ABX00053, Nano RP2040 Hokela le Lihlooho, ABX00053 Nano RP2040 Hokela le Lihlooho |
 |
ARDUINO ABX00053 Nano RP2040 Connect [pdf] Bukana ea Mosebelisi ABX00053, Nano RP2040 Connect |
 |
ARDUINO ABX00053 Nano RP2040 Hokela le Lihlooho [pdf] Bukana ea Mosebelisi ABX00053, Nano RP2040 Hokela le Lihlooho, ABX00053 Nano RP2040 Hokela le Lihlooho |
 |
ARDUINO ABX00053 Nano RP2040 Hokela le Lihlooho [pdf] Bukana ea Mosebelisi ABX00053, Nano RP2040 Hokela le Lihlooho, ABX00053 Nano RP2040 Hokela le Lihlooho |
