STM32 Industrial Input Output Expansion Board User Manual

The dual-channel digital isolators provide galvanic isolation
between user and power interfaces. They offer robustness to noise
and high-speed input/output switching time.

High-side Switches (IPS1025H-32 and IPS1025HQ-32):

The high-side switches on the board feature overcurrent and
overtemperature protection for safe output load control. They have
an application board operating range of 8 to 33 V and 0 to 2.5 A.
Ensure compatibility with STM32 Nucleo development boards.

High-side Current Limiter (CLT03-2Q3):

The high-side current limiter can be configured for both
high-side and low-side applications. It offers galvanic isolation
between process and login sides, with important features like 60 V
and reverse input plugin capability.

FAQ:

Q: What should I do if the side switches get heated?

A: Care must be taken while touching the IC or adjoining areas
on the boards, particularly with higher loads. If the switches get
heated, reduce the load current or contact our online support
portal for assistance.

Q: What do the LEDs on the board indicate?

A: The green LED corresponding to each output indicates when a
switch is ON, while red LEDs indicate overload and overheating
kuaj mob.

“`

View Fullscreen

UWM 3483
Cov neeg siv phau ntawv
Getting started with the X-NUCLEO-ISO1A1 industrial input/output expansion board for STM32 Nucleo
Taw qhia
The X-NUCLEO-ISO1A1 evaluation board is designed to expand the STM32 Nucleo board and provide micro-PLC functionality with isolated industrial input and output. Isolation between logic and process side components is provided by the UL1577 certified digital isolators STISO620 and STISO621. Two current-limited high-side inputs from the process side are realized through the CLT03-2Q3. Protected outputs with diagnostics and smart driving features are provided by one each of the high-side switches IPS1025H/HQ and IPS1025H-32/ HQ-32 which can drive capacitive, resistive, or inductive loads up to 5.6 A. Two X-NUCLEO-ISO1A1 boards can be stacked together on top of an STM32 Nucleo board via ST morpho connectors with the appropriate selection of jumpers on the expansion boards to avoid conflict in GPIO interfaces. Rapid evaluation of the onboard ICs is facilitated by the X-NUCLEO-ISO1A1 using the X-CUBE-ISO1 software package. Provision for ARDUINO® connections is provided on the board.
Figure 1. X-NUCLEO-ISO1A1 expansion board

Daim ntawv ceeb toom:

Rau kev pab tshwj xeeb, xa daim ntawv thov los ntawm peb lub vev xaib txhawb nqa online ntawm www.st.com/support.

UM3483 - Rev 1 - Tsib Hlis 2025 Yog xav paub ntxiv, hu rau koj lub chaw muag khoom hauv STMicroelectronics.

www.st.com

UWM 3483
Cov ntaub ntawv kev nyab xeeb thiab kev ua raws cai

Cov ntaub ntawv kev nyab xeeb thiab kev ua raws cai

The side switches IPS1025HQs may get heated with high load current. Care must be taken while touching the IC or adjoining areas on the boards. particularly with higher loads.

1.1

Compliance information (Reference)

Both CLT03-2Q3 and IPS1025H are designed to meet common industrial requirements, including IEC61000-4-2, IEC61000-4-4, and IEC61000-4-5 standards. For a more detailed evaluation of these components, refer to the single-product evaluation boards available at www.st.com. The X-NUCLEO-ISO1A1 serves as an excellent tool for initial assessments and rapid prototyping, providing a robust platform for developing industrial applications with STM32 Nucleo boards. Additionally, the board is RoHS compliant and comes with a free comprehensive development firmware library and examples compatible with STM32Cube firmware.

UM3483 – Rev 1

paj 2/31

Cov duab kos duab

The different components on the board are shown here, with description.

U1 – CLT03-2Q3: Input current limiter

U2, U5 – STISO620: ST digital isolator unidirectional

U6, U7 – STISO621: ST digital isolator bidirectional.

U3 – IPS1025HQ-32: high-side switch (package: 48-VFQFN Exposed Pad)

U4 – IPS1025H-32: high-side switch (package: PowerSSO-24).

U8 – LDO40LPURY: Voltagib regulator

Figure 2. Different ST ICs and their position

UWM 3483
Cov duab kos duab

UM3483 – Rev 1

paj 3/31

UWM 3483
Tshajview

Tshajview

The X-NUCLEO-ISO1A1 is an industrial I/O evaluation board with two inputs and outputs. It is designed to be operated with an STM32 Nucleo board such as NUCLEO-G071RB. Compatible with the ARDUINO® UNO R3 layout, it features the STISO620 dual-channel digital isolator and IPS1025H-32 and IPS1025HQ-32 high-side switches. The IPS1025H-32 and IPS1025HQ-32 are single high-side switch ICs capable of driving capacitive, resistive, or inductive loads. The CLT03-2Q3 provides protection and isolation in industrial operating conditions and offers an ‘energy-less’ status indication for each of the two input channels, featuring minimal power consumption. It is designed for situations that require compliance with IEC61000-4-2 standards. The STM32 MCU on board the controls and monitors all the devices via GPIOs. Each input and output have an LED indication. In addition, there are two programmable LEDs for customizable indications. The X-NUCLEO-ISO1A1 enables rapid evaluation of the onboard ICs by performing a basic set of operations in conjunction with the X-CUBE-ISO1 software package. The key features of the constituent components are given below.

3.1

Dual-channel digital isolator

The STISO620 and STISO621 are dual-channel digital isolators based on the ST thick oxide galvanic isolation technology.

The devices provide two independent channels in the opposite direction (STISO621) and in the same direction (STISO620) with Schmitt trigger input as shown in Figure 3, providing robustness to noise and high-speed input/ output switching time.

It is designed to operate within a wide ambient temperature range from -40 ºC to 125 ºC, making it suitable for various environmental conditions. The device boasts a high common-mode transient immunity exceeding 50 kV/µs, ensuring robust performance in electrically noisy environments. It supports supply levels ranging from 3 V to 5.5 V and provides level translation between 3.3 V and 5 V. The isolator is engineered for low-power consumption and features pulse width distortions of less than 3 ns. It offers 6 kV (STISO621) and 4 kV (STISO620) galvanic isolation, enhancing safety and reliability in critical applications. The product is available in both SO-8 narrow and wide package options, providing flexibility in design. Additionally, it has received safety and regulatory approvals, including UL1577 certification.

Figure 3. ST digital isolators

UM3483 – Rev 1

paj 4/31

UWM 3483
Tshajview

3.2

High-side switches IPS1025H-32 and IPS1025HQ-32

The X-NUCLEO-ISO1A1 embeds the IPS1025H-32 and IPS1025HQ-32 intelligent power switch (IPS), featuring overcurrent and overtemperature protection for safe output load control.

The board is designed to meet application requirements in terms of galvanic isolation between user and power interfaces using ST’s new technology STISO620 and STISO621 ICs. This requirement is satisfied by a dualchannel digital isolator based on the ST thick oxide galvanic isolation technology.

The system utilizes two STISO621 bidirectional isolators, labeled as U6 and U7, to facilitate the forward transmission of signals to the device, as well as to handle the FLT pins for feedback diagnostic signals. Each high-side switch generates two fault signals, necessitating the inclusion of an additional unidirectional isolator, designated as U5, which is digital isolator STISO620. This configuration ensures that all diagnostic feedback is accurately isolated and transmitted, maintaining the integrity and reliability of the system’s fault detection and signaling mechanisms.

The industrial outputs on the board are based on the IPS1025H-32 and IPS1025HQ-32 single high-side

switch, which features:

Operating range up to 60 V

Low-power dissipation (RON = 12 m)

Fast decay for inductive loads

Smart driving of capacitive loads

Undervoltage xauv

Overload and overtemperature protection

PowerSSO-24 and QFN48L 8x6x0.9mm package

Daim ntawv thov kev khiav hauj lwm ntau yam: 8 ~ 33 V / 0 ~ 2.5 A

Extended voltage kev khiav hauj lwm ntau (J3 qhib) mus txog 60 V

5 kV galvanic cais

Muab rail rov qab polarity tiv thaiv

EMC compliance with IEC61000-4-2, IEC61000-4-3, IEC61000-4-4, IEC61000-4-5, IEC61000-4-8

Tau tshaj STM32 Nucleo txhim kho pawg thawj coj saib

Nruab nrog Arduino® UNO R3 connectors

CE tau ntawv pov thawj:

EN 55032:2015 + A1:2020

EN 55035:2017 + A11:2020.

Green LED corresponding to each output indicates when a switch is ON. Also Red LEDs indicates overload and overheating diagnostics.

UM3483 – Rev 1

paj 5/31

UWM 3483
Tshajview

3.3

High-side current limiter CLT03-2Q3

The X-NUCLEO-ISO1A1 board has two input connectors for any industrial digital sensors, such as proximity, capacitive, optical, ultrasonic, and touch sensors. Two of the inputs are intended for isolated lines with optocouplers on the outputs. Each input then feeds directly into one of the two independent channels in CLT03-2Q3 current limiters. The channels in the current limiter immediately limit the current as per the standard and proceed to filter and regulate the signals to deliver appropriate outputs for the isolated lines destined for the GPIO ports of a logic processor, such as a microcontroller in a programmable logic controller (PLC). The board also includes jumpers to enable test pulses through any of the channels to verify normal operation.

Isolator STISO620 (U2) is used for Galvanic isolation between process and login side.

Cov yam ntxwv tseem ceeb:

The 2 isolated channel input current limiter can be configured for both high-side and low-side applications

60 V and reverse input plugin capable

Tsis xav tau lub hwj chim

Safety test pulse

High EMI robustness thanks to integrated digital filter

IEC61131-2 type 1 and type 3 compliant

Raws li RoHS

The input side of the CLT03-2Q3 current limiter is characterized by certain voltage and current ranges that delimit ON and OFF regions, as well as transition regions between these logical high and low states. The device enters Fault Mode when the input voltage tshaj 30v.

Figure 4. Input characteristics of CLT03-2Q3

UM3483 – Rev 1

paj 6/31

Figure 5. Output operating region of CLT03-2Q3

UWM 3483
Tshajview

UM3483 – Rev 1

paj 7/31

UWM 3483
Functional blocks

Functional blocks

The board is designed to operate with nominal 24V input which powers the process side circuitry. The logic component on the other side of isolators are powered by 5 V input to the X-NUCLEO board which is typically powered by a USB port of a PC.
Daim duab 6. Daim duab thaiv

4.1

Process side 5 V supply

A 5V supply is derived from 24V input with low drop regulator LDO40L with built in protection functions. The voltage regulator has a self-overheating turn-off feature. The output voltage can be adjusted and kept just below the 5V utilising a retorsion network feeback from output. The LDO has DFN6 (Wettable flanks), which make this IC suitable for board size optimization.

Figure 7. Process side 5 V supply

UM3483 – Rev 1

paj 8/31

UWM 3483
Functional blocks

4.2

Isolator STISO621

The STISO621 digital isolator has 1-to-1 directionality, with 100MBPS data rate. It can withstand, 6KV galvanic isolation and high common-mode transient: >50 k V/s.

Figure 8. Isolator STISO621

4.3

Isolator STISO620

The STISO620 digital isolator has from 2-to-0 directionality, with 100MBPS data rate as the STISO621. It can withstand, 4KV galvanic isolation and has a Schmitt trigger input.

Figure 9. Isolator STISO620

UM3483 – Rev 1

paj 9/31

UWM 3483
Functional blocks

4.4

Current limited digital input

The current limiter IC CLT03-2Q3 has two isolated channels, where we can connect isolated inputs. The board has an input excitation LED indicator.

Figure 10. Current-limited digital input

4.5

High-side switch (with dynamic current control)

The high-side switches are available in two packages with identical features. In this board, both the packages, that is, POWER SSO-24 and 48-QFN(8*x6), are used. The details features are mentioned in the Overview ntu.

Figure 11. High-side switch

UM3483 – Rev 1

paj 10/31

UWM 3483
Functional blocks

4.6

Jumper setting options

The control and status pins of the I/O devices are connected through jumpers to the MCU GPIO. The jumper selection allows connection of each control pin to one of two possible GPIOs. To simplify, these GPIOs are clubbed in two sets marked as default and alternate. The serigraphy on the boards includes bars that indicate the jumper positions for default connections. The standard firmware assumes that one of the sets, marked as default and alternate, is selected for a board. The figure below depicts the jumper information for routing control and status signals between the X-NUCLEO and suitable Nucleo boards through the Morpho connectors for various configurations.

Figure 12. Morpho connectors

Through this jumper connection, we can stack one more X-NUCLEO, which is fully functional.

UM3483 – Rev 1

paj 11/31

Figure 13. MCU interface routing options

UWM 3483
Functional blocks

UM3483 – Rev 1

paj 12/31

UWM 3483
Functional blocks

4.7

LED ntsuas

Two LEDs, D7 and D8 are provided on the board to have programmable LED indications. Refer to the software user manual for detailed information on various LED configurations and features, including power status and error states.

Daim duab 14. LED qhia

UM3483 – Rev 1

paj 13/31

Board setup and configuration

UWM 3483
Board setup and configuration

5.1

Pib nrog lub rooj tsavxwm

A detailed image is provided to help you become familiar with the board and its various connections. This image serves as a comprehensive visual guide, illustrating the layout and specific points of interest on the board. Terminal J1 is provided to connect 24V supply to power the process side of the board. Terminal J5 is also connected to the 24V DC input. However J5 is provided easy connection of external Loads and Sensors which are connected to Input terminal J5 and high side output terminal J12.

Figure 15. Different connecting ports of X-NUCLEO

UM3483 – Rev 1

paj 14/31

UWM 3483
Board setup and configuration

5.2

Cov kev xav tau ntawm kev teeb tsa

1. 24 V DC Power Supply: The 2$V input should have sufficient capability to drive the board along with external load. Ideally this should be short circuit protected externals.

2. NUCLEO-G071RB Board: The NUCLEO-G071RB board is a Nucleo development board. It serves as the main microcontroller unit for driving outputs, monitoring output health status, and fetching process side inputs.

3. X-NUCLEO-ISO1A1 Board: The Micro PLC board for evaluation of specific functionality of the devices. We can stack two X-NUCLEO as well.

4. USB-micro-B Cable: The USB-micro-B cable is used to connect the NUCLEO-G071RB board to a computer or a 5 V adapter. This cable is essential for flashing the binary file onto the mentioned Nucleo board and
subsequently powering it through any 5 V charger or adapter.

5. Wires to connect the Input Supply: Connecting wire for the load and inputs, it is highly recommended to use thick wires for the output high-side switches.

6. Laptop/PC: A laptop or PC has to be used to flash the test firmware onto the NUCLEO-G071RB board. This process only needs to be performed once when using the Nucleo board to test multiple X-NUCLEO boards.

7. STM32CubeProgrammer (optional): The STM32CubeProgrammer is used to flash the binary after erasing the MCU chip. It is a versatile software tool designed for all STM32 microcontrollers, providing an efficient way to program and debug the devices. More information and the software can be found at STM32CubeProg STM32CubeProgrammer software for all STM32 – STMicroelectronics.

8. Software (optional): Install the ‘Tera Term’ software on your desktop to facilitate communication with the Nucleo board. This terminal emulator allows for easy interaction with the board during testing and debugging.
The software can be downloaded from Tera-Term.

5.3

Kev tiv thaiv kev nyab xeeb thiab cov cuab yeej tiv thaiv

Applying a heavy load through the high-side switches may cause the board to overheat. A warning sign is placed near the IC to indicate this risk.

It has been observed that the board has reduced tolerance to relatively high voltage surges. Therefore, it is advised not to connect excessive inductive loads or apply increased voltage beyond the specified reference values. It is expected that the board should be handled by an individual with basic electrical knowledge.

5.4

Stacking of two X-NUCLEO board on Nucleo

The board is designed with a jumper configuration that enables the Nucleo to drive two X-NUCLEO boards, each with two outputs and two inputs. Additionally, the fault signal is configured separately. Please refer to the table below as well as the schematic described in the previous section to configure and route control and monitoring signal between the MCU and devices. Either Default or alternate jumper can used while using single X-Nucleo board. But the both the X-nucleo boards should have different jumper selection to avod clash incase they are stacked on top another.

Table 1. Jumper selection chart for the default and alternate configuration

PIN feature

Serigraphy on board

Schematic name

Jumper

Default configuration

Header setting

Lub npe

IA.0 Input (CLT03)
IA.1

IA0_IN_L

j18 ua

IA1_IN_L

j19 ua

1-2(CN2PIN-18)
1-2(CN2PIN-36)

IA0_IN_1 IA1_IN_2

Hloov configuration

Header setting

Lub npe

2-3(CN2PIN-38)

IA0_IN_2

2-3(CN2PIN-4)

IA1_IN_1

UM3483 – Rev 1

paj 15/31

UWM 3483
Board setup and configuration

PIN feature

Serigraphy on board

Schematic name

Jumper

Default configuration

Header setting

Lub npe

Hloov configuration

Header setting

Lub npe

Output (IPS-1025)

QA.0 QA.1

QA0_CNTRL_ L

j22 ua

QA1_CNTRL_ L

j20 ua

1-2(CN2PIN-19)

QA0_CNTRL_ 2-3(CN1-

PIN-2)

1-2(CN1- PIN-1)

QA1_CNTRL_ 2

2-3(CN1PIN-10)

QA0_CNTRL_ 2
QA1_CNTRL_ 1

FLT1_QA0_L J21

1-2(CN1- PIN-4) FLT1_QA0_2

2-3(CN1PIN-15)

FLT1_QA0_1

Fault PIN configuration

FLT1_QA1_L J27 FLT2_QA0_L J24

1-2(CN1PIN-17)

FLT1_QA1_2

1-2(CN1- PIN-3) FLT2_QA0_2

2-3(CN1PIN-37)
2-3(CN1PIN-26)

FLT1_QA1_1 FLT2_QA0_1

FLT2_QA1_L J26

1-2(CN1PIN-27)

FLT2_QA1_1

2-3(CN1PIN-35)

FLT2_QA1_2

The image indicates the different views of the X-NUCLEO stacking. Figure 16. Stack of two X-NUCLEO boards

UM3483 – Rev 1

paj 16/31

UWM 3483
How to set up the board (tasks)

How to set up the board (tasks)

Jumper connection Make sure all the jumpers are in the default state; a white bar indicates the default connection. As shown in Figure 2. The FW is configure d for default jumper selection. appropriate modifications are needed to use alternate jumper selections.
Figure 17. Jumper connection of X-NUCLEO-ISO1A1

1. Connect the Nucleo board via a micro-USB cable to the computer
2. Place the X-NUCLEO on top of Nucleo as shown in Figure 18
3. Copy the X-CUBE-ISO1.bin to the Nucleo disc, or refer to the software user manual for software debugging
4. Check the D7 LED on the stacked X-NUCLEO Board; it should blink 1 second ON and 2 seconds OFF as shown in Figure 5. You can also debug the X-CUBE-ISO1 firmware using STM32CubeIDE and other supported IDEs.Fig. 18 below shows LED indications with all Inputs as low followed by all high input to the board. Output mimics the corresponding input.

UM3483 – Rev 1

paj 17/31

UWM 3483
How to set up the board (tasks)
Figure 18. LED indication pattern during normal board operation

UM3483 – Rev 1

paj 18/31

UM3483 – Rev 1

Schematic daim duab

J1
1
Te rmina lBlock
24V DC Input

Figure 19. X-NUCLEO-ISO1A1 circuit schematic (1 of 4)
24v XNUMX

C1 NIM
P C Te s t P oint,
1

GND_EARTH

Ntiaj teb

R1 R
C2 D1 S M15T33CA

C4 10 UA

U8 3 VIN Vout 4
2 ENV Sense 5
1 GND ADJ 6
LDO40LPURY

PAB 1
R2 12K ib
R4 36K ib

5v TP 10
1

C5 10 UA

D2 Gre e n LED
R3

J5
1
nkag

D4 Gre e n LED
R10

D3 Gre e n LED
R5

IA.0H

IA.1H

GND

J6
1

24v XNUMX
C15

GND

Field Side Connections GND
Figure 20. X-NUCLEO-ISO1A1 circuit schematic (2 of 4)

3v 3

Xyoo 10nF

r490 ua

TIAB SA 2

C25

C26

6 INATTL1 7 INA1 8 INB1

TP1 VBUF1 OUTP1 OUTN1 OUTN1_T
PD 1

9 10 11 5 TAB1 12

Xyoo 10nF

O UTP 1 OUTN1
r490 ua

R38 220K ib
TIAB SA 3

2 INATTL2 3 INA2 4 INB2

TP2 VBUF2 OUTP2 OUTN2 OUTN2_T
PD 2

14 15 16 13 TAB2 1

C8 10nF O UTP 2
OUTN2

R37 220K ib

GND

1 2

VDD1 TxA TxB GND1

VDD2 RxA RxB
NTS2

8 7

S T1S O620
Isolation Barrier

GND_Logic TP4
1

IA0_IN_L IA1_IN_L

R35 0E 0E R36

Xyoo 10nF

CLT03-2Q3

GND

GND_Logic

R7, R9

Can be replaced by a capacitor for test purpose

From Field Side

UWM 3483
Schematic daim duab
To STM32 Nucleo

GND

Input Current Limiter with Digital Isolation

paj 19/31

UM3483 – Rev 1

Figure 21. X-NUCLEO-ISO1A1 circuit schematic (3 of 4)

High side Switch Section

C17

24V FLT2_QA0

QA.0

J12 1A 2A
OUTPUT

C16 24 V

FLT2_QA1 QA.1

1 2 3 4 5 6 7 8 9 10 11 12

VCC NC NC FLT2 OUT OUT OUT OUT OUT OUT OUT OUT

GND IB
IPD FLT1 OUT OUT OUT OUT OUT OUT OUT OUT

24 23 22 21 20 19 18 17 16 15 14 13

IP S 1025HTR-32

GND
QA0_CNTRL_P
R14 220K ib

FLT1_QA0

J 10

3 pin jumpe r

Gre e n LED

2d 6

R15
C 11 0.47 µF

J 11

3 pin jumpe r

R16

10k ua

GND

0 2 1 13 42 41 17 18 19 20 21 22

VCC NC NC FLT2 OUT OUT OUT OUT OUT OUT OUT OUT

GND IB
IPD FLT1 OUT OUT OUT OUT OUT OUT OUT OUT

6 3 48 46 40 39 38 37 36 35 24 23

IP S 1025HQ-32

GND

QA1_CNTRL_P
R11 220K ib

FLT1_QA1

3 pin jumpe r

Gre e n LED

2d 5

R13

R12

C10

3 pin jumpe r

0.47f ua

10k ua

GND

3v 3
C22 FLT1_QA0_L QA0_CNTRL_L

GND_Logic 3V3

FLT1_QA1_L C20
QA1_CNTRL_L

TIAB SA 6

Kev cais cais

U6
1 VDD1 2 RX1 3 TX1 4 GND1
S TIS O621

VDD2 8 TX2 7 RX2 6
Nc2 5

5V
FLT1_QA0 QA0_CNTRL_P C23
R28 220K R29 220K

U7
1 VDD1 2 RX1 3 TX1 4 GND1
S TIS O621

VDD2 8 TX2 7 RX2 6
Nc2 5

GND 5 V

FLT1_QA1

QA1_CNTRL_P

C21

R30 220K R31 220K

TIAB SA 7

GND_Logic 5V

FLT2_QA0

C18

FLT2_QA1

R33 220K R32 220K

GND

1 2

VDD1 TxA
TxB GND1

VDD2 RxA
RxB GND2

8 7

S T1S O620

GND 3V 3

FLT2_QA0_L

C19

FLT2_QA1_L

GND_Logic

To Field

UWM 3483
Schematic daim duab

paj 20/31

UM3483 – Rev 1

3v3v 3

QA1_CNTRL_2 FLT2_QA0_2

C13

FLT1_QA0_1

FLT1_QA1_2

GND_Logic

r490 ua
FLT2_QA1_1

FLT2_QA1_2 FLT1_QA1_1

Figure 22. X-NUCLEO-ISO1A1 circuit schematic (4 of 4)

CN 1
1
3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35

QA0_CNTRL_2

FLT1_QA0_2

QA1_CNTRL_1

14 B2

16 3V 3

LOGIC_GND

3v 3

FLT2_QA0_1

r490 ua

Le ft Ha nd S ide Conne ctor

GND_Logic

r490 ua

Morpho Connectors

CN 2

D15

D14

r17v 3

0E AGND

R26

R27

D13 11

D12 13

GND_Logic

D11 15

D10 17

D9′

R19 NM QA0_CNTRL_1 D9

XAJ LED

D8 liab LED

R20 NM

R21

GND_Logic

IA1_IN_1
IA0_IN_1 TP8
AGND IA1_IN_2 IA0_IN_2
GND_Logic

[ Note: Header PIN 1 and 2 to be shorted for All Default configuration. ]

2 FLT2_QA0_L

FLT2_QA0_2
J 24 3 pin jumpe r
QA0_CNTRL_L

QA0_CNTRL_1

FLT1_QA0_2

J 22

3 pin jumpe r

J 21

3 pin jumpe r

FLT1_QA0_L

FLT2_QA0_1

2 FLT1_QA1_L

FLT1_QA1_2
J 27 3 pin jumpe r

QA0_CNTRL_2 FLT2_QA1_1

FLT1_QA0_1 QA1_CNTRL_2

2 FLT2_QA1_L

J 26 3 pin jumpe r
2
QA1_CNTRL_L

J 20 3 pin jumpe r

FLT1_QA1_1

FLT2_QA1_2

QA1_CNTRL_1

2 IA1_IN_L
2 IA0_IN_L

IA1_IN_2 J 19 3 pin jumpe r
IA1_IN_1
IA0_IN_1 J 18 3 pin jumpe r
IA0_IN_2

MCU Interface Routing Options

CN 6
1 2 3 4 5 6 7 8
NM

3v 3
B2 3V3
LOGIC_GND

3v 3
3V3 C24
AGND NM

D 15D14
D13 D12 D11 D10 D9′ D8

CN 4

1 2 3 4 5 6 7 8

D0 D1 D2
D3 D4 D5
D 6D7

CN 3
10 9 8 7 6 5 4 3 2 1
NM

CN 5

1
3
5

A0 A1 A2 A3 A4 A5

Arduino Connectors

UWM 3483
Schematic daim duab

paj 21/31

UWM 3483
Bill ntawm cov ntaub ntawv

Bill ntawm cov ntaub ntawv

Table 2. X-NUCLEO-ISO1A1 bill of materials

Item Q.ty

Ref.

1 1 BD1

2 2 C1, C3

3 2 C10, C11

C13, C18, C19,

C20, C21, C22, C23, C24, C25,

C26

5 2 C2, C15

6 2 C16, C17

7 1c4

8 1c5

9 4 C6, C7, C8, C9

10 2 CN1, CN2

11 1 ZPO 3

12 2 CN4, CN6

13 1 ZPO 5

14 1 D1, SMC

D2, D3, D4, D5, D6, D7

16 1d8

17 2 HW1, HW2

18 1j1

19 1j2

20 1j5

21 2 J6, J12

J8, J9, J10, J11,

J18, J19, J20, J21, J22, J24,

j26,j 27

23 1r1

R11, R14, R28, R29, R30, R31, R32, R33

Part/value 10OHM 4700pF
0.47f ua

Kev piav qhia

Chaw tsim tshuaj paus

Ferrite Beads WE-CBF Würth Elektronik

Safety Capacitors 4700pF

Vishay

Multilayer Ceramic Capacitors

Würth Elektronik

Order code 7427927310 VY1472M63Y5UQ63V0
885012206050

Xyoo 100nF

Multilayer Ceramic Capacitors

Würth Elektronik

885012206046

1uF 100nF 10uF 10uF 10nF
465 VAC, 655 VDC 465 VAC, 655 VDC 5.1A 1.5kW(ESD) 20mA 20mA Jumper CAP 300VAC
300VAC lossis 300VAC

Multilayer Ceramic Capacitors

Würth Elektronik

885012207103

Multilayer Ceramic Capacitors

Würth Elektronik

885382206004

Multilayer Ceramic Capacitors

Murata Electronics GRM21BR61H106KE43K

Multilayer Ceramic Capacitors, X5R

Murata Electronics GRM21BR61C106KE15K

Multilayer Ceramic Capacitors

Würth Elektronik

885382206002

Headers & Wire Housings

Samtec

Qauv: SSQ-119-04-LD

Headers & Wire Housings

Samtec

TSW-110-03-LS

8 Position Receptacle Connector

Samtec

TSW-108-03-LS

Headers & Wire Housings

Samtec

TSW-106-03-LS

ESD Suppressors / TVS Diodes

STMicroelectronics SM15T33CA

Standard LEDs SMD(Green)

Broadcom Limited ASCKCG00-NW5X5020302

Standard LEDs SMD(Red)

Broadcom Limited ASCKCR00-BU5V5020402

Jumper

Würth Elektronik

609002115121

Fixed Terminal Blocks Würth Elektronik

691214110002

Test Plugs & Test Jacks Keystone Electronics 4952

Fixed Terminal Blocks Würth Elektronik

691214110002

Fixed Terminal Blocks Würth Elektronik

691214110002

Headers & Wire Housings

Würth Elektronik

61300311121

10OHM 220 kOhms

Thin Film Resistors SMD

Vishay

Thick Film Resistors SMD

Vishay

TNPW080510R0FEEA RCS0603220KJNEA

UM3483 – Rev 1

paj 22/31

UWM 3483
Bill ntawm cov ntaub ntawv

Item Q.ty

Ref.

25 2 R12, R16

Part/value 10KOHM

26 1r19

0 hmo

27 1r2

12 Nws

28 2 R26, R27

150 AWM

29 4 R3, R13, R15

1 Nws

30 2 R35, R36

0 hmo

31 2 R37, R38

220 kwm

32 1r4

36 Nws

33 2 R5, R10

7.5 Nws

34
35
36 4 37 3 38 1 39 2 40 1
41 1 42 2 43 1 ib

R6, R8

0 hmo

R7, R9, R17, R20, R21, R23, R24, R34
TP 2, TP 3, TP 8, TP 10
TXP 4, TP6, TP7

0 hmo

U1, QFN-16L

U2, U5, SO-8

U3, VFQFPN 48L 8.0 X 6.0 X .90 3.5A PITCH

U4, PowerSSO 24

3.5 A

U6, U7, SO-8

U8, DFN6 3×3

Kev piav qhia
Thick Film Resistors SMD
Thick Film Resistors SMD
Thin Film Resistors SMD
Thin Film Chip Resistors
Thin Film Resistors SMD
Thick Film Resistors SMD
Thick Film Resistors SMD
Thick Film Resistors SMD
Thin Film Resistors SMD
Thick Film Resistors SMD

Manufacturer Bourns Vishay Panasonic Vishay Vishay Vishay Vishay Panasonic Vishay Vishay

Thick Film Resistors SMD

Vishay

Test Plugs & Test Jacks Harwin

Self-powered digital input current limiter

STMicroelectronics

Digital Isolators

STMicroelectronics

HIGH-SIDE SWITCH STMicroelectronics

Power Switch/Driver 1:1

N-Channel 5A

STMicroelectronics

PowerSSO-24

Digital Isolators

STMicroelectronics

LDO Voltage Regulators

STMicroelectronics

Order code CMP0603AFX-1002ELF CRCW06030000Z0EAHP ERA-3VEB1202V MCT06030C1500FP500 CRCW06031K00DHEBP CRCW06030000Z0EAHP RCS0603220KJNEA ERJ-H3EF3602V TNPW02017K50BEED CRCW06030000Z0EAHP
CRCW06030000Z0EAHP
S2761-46R S2761-46R CLT03-2Q3 STISO620TR IPS1025HQ-32
IPS1025HTR-32 STISO621 LDO40LPURY

UM3483 – Rev 1

paj 23/31

UWM 3483
Board versions

Board versions

Table 3. X-NUCLEO-ISO1A1 versions

Tiav lawm zoo

Schematic daim duab

X$NUCLEO-ISO1A1A (1)

X$NUCLEO-ISO1A1A schematic diagrams

1. This code identifies the X-NUCLEO-ISO1A1 evaluation board first version.

Bill of materials X$NUCLEO-ISOA1A bill of materials

UM3483 – Rev 1

paj 24/31

UWM 3483
Cov ntaub ntawv tswj kev ua raws cai

Cov ntaub ntawv tswj kev ua raws cai

Daim ntawv ceeb toom rau US Tsoom Fwv Teb Chaws Kev Sib Txuas Lus Commission (FCC)
Kev ntsuam xyuas nkaus xwb; Tsis yog FCC pom zoo rau kev muag khoom FCC TEEB MEEM - Cov khoom siv no yog tsim los tso cai: (1) Cov neeg tsim khoom lag luam los ntsuas cov khoom siv hluav taws xob, cov khoom siv hluav taws xob, lossis cov software cuam tshuam nrog cov khoom siv los txiav txim seb puas yuav suav nrog cov khoom zoo li no hauv cov khoom tiav thiab (2) Cov neeg tsim khoom siv software los sau cov ntawv thov software siv nrog cov khoom kawg. Cov khoom siv no tsis yog cov khoom tiav thiab thaum sib sau ua ke yuav tsis raug muag lossis ua lag luam tshwj tsis yog txhua qhov yuav tsum tau muaj kev tso cai FCC thawj zaug. Kev ua haujlwm yog nyob rau hauv cov xwm txheej uas cov khoom no tsis ua rau muaj teeb meem cuam tshuam rau cov chaw nres tsheb xov tooj cua uas muaj ntawv tso cai thiab cov khoom no lees txais kev cuam tshuam tsis zoo. Tshwj tsis yog cov khoom siv sib sau ua ke tsim los ua haujlwm raws li ntu 15, ntu 18 lossis ntu 95 ntawm tshooj no, tus neeg siv khoom siv yuav tsum ua haujlwm raws li txoj cai ntawm FCC daim ntawv tso cai lossis yuav tsum muaj kev tso cai rau kev sim raws li ntu 5 ntawm tshooj 3.1.2.
Daim ntawv ceeb toom rau Innovation, Science thiab Economic Development Canada (ISED)
Rau kev ntsuam xyuas nkaus xwb. Cov khoom siv no tsim tawm, siv, thiab tuaj yeem tawg lub zog ntawm lub xov tooj cua thiab tsis tau sim ua raws li cov kev txwv ntawm cov khoom siv suav nrog raws li Kev Lag Luam Canada (IC) cov cai. Lub des fins d'évaluation uniquement. Ce kit génère, utilize et peut émettre de l'énergie radiofréquence et n'a pas été testé pour sa conformité aux limites des appareils informatiques conformément aux règles d'Industrie Canada (IC).
Daim ntawv ceeb toom rau European Union
Cov cuab yeej no ua raws li cov cai tseem ceeb ntawm Cov Lus Qhia 2014/30/EU (EMC) thiab Cov Lus Qhia 2015/863/EU (RoHS).
Daim ntawv ceeb toom rau United Kingdom
Cov cuab yeej no tau ua raws li UK Electromagnetic Compatibility Regulations 2016 (UK SI 2016 No. 1091) thiab nrog rau kev txwv tsis pub siv qee yam phom sij hauv cov khoom siv hluav taws xob thiab hluav taws xob 2012 (UK SI 2012 No. 3032).

UM3483 – Rev 1

paj 25/31

Cov ntawv txuas ntxiv
Ib example is described here for the easy use and handling of the board. Example – Digital input and Digital Output test case 1. Stack the X-NUCLEO Board onto the Nucleo board 2. Debug the code using a Micro- B Cable 3. Call this function in the main, “ST_ISO_APP_DIDOandUART” 4. Connect the 24V Power supply as shown in the image
Figure 23. Digital Input and Digital Output Implementation

UWM 3483

5. The input and the respective output follow the chart as mentioned in the chart below. Figure on the left corresponds to row 1 and figure on the right corresponds to row 4 of Table 4.

Case No.
1 2

D3 LED(IA.0) Input
0V 24V 0V 24V

Table 4. DIDO Logic Table

D4 LED(IA.1) Input
0V 0V 24V 24V

D6 LED(QA.0) Output
Tawm tawm OFF ON

D5 LED(QA.1) Output
Tawm OFF ON ON

The demo serves as an easy start guide for quick hands-on experience. Users may also invoke additional functions for their specific needs.

UM3483 – Rev 1

paj 26/31

Kev kho keeb kwm
Hnub tim 05-May-2025

Table 5. Cov ntaub ntawv kho dua tshiab

Hloov kho 1

Kev tso tawm thawj zaug.

Hloov

UWM 3483

UM3483 – Rev 1

paj 27/31

UWM 3483
Cov ntsiab lus
Cov ntsiab lus
1 Safety and compliance information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 1.1 Compliance information (Reference) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
2 Component diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 3 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
3.1 Dual-channel digital isolator. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 3.2 High-side switches IPS1025H-32 and IPS1025HQ-32. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 3.3 High-side current limiter CLT03-2Q3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 4 Functional blocks. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8 4.1 Process side 5 V supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 4.2 Isolator STISO621. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 4.3 Isolator STISO620 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 4.4 Current limited digital input. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 4.5 High-side switch (with dynamic current control) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 4.6 Jumper setting options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 4.7 LED indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 5 Board setup and configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14 5.1 Get started with the board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 5.2 System setup requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 5.3 Safety precautions and protective equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 5.4 Stacking of two X-NUCLEO board on Nucleo . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 6 How to set up the board (tasks) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17 7 Schematic diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19 8 Bill of materials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22 9 Board versions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24 10 Regulatory compliance information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25 Appendices. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26 Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27 List of tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29 List of figures. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

UM3483 – Rev 1

paj 28/31

UWM 3483
Daim ntawv teev cov rooj

Daim ntawv teev cov rooj

Table 1. Table 2. Table 3. Table 4. Table 5.

Jumper selection chart for the default and alternate configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 X-NUCLEO-ISO1A1 bill of materials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 X-NUCLEO-ISO1A1 versions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 DIDO Logic Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Document revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

UM3483 – Rev 1

paj 29/31

UWM 3483
Daim ntawv teev cov duab

Daim ntawv teev cov duab

Daim duab 1. Daim duab 2. Daim duab 3. Daim duab 4. Daim duab 5. Daim duab 6. Daim duab 7. Daim duab 8. Daim duab 9. Daim duab 10. Daim duab 11. Daim duab 12. Daim duab 13. Daim duab 14. Daim duab 15. Daim duab 16. Daim duab 17. Daim duab 18. Daim duab 19. Daim duab 20. Daim duab 21.

X-NUCLEO-ISO1A1 expansion board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Different ST ICs and their position . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 ST digital isolators. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Input characteristics of CLT03-2Q3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Output operating region of CLT03-2Q3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Thaiv daim duab. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Process side 5 V supply. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Isolator STISO621 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Isolator STISO620 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Current-limited digital input. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 High-side switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Morpho connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 MCU interface routing options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 LED qhov taw qhia. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Different connecting ports of X-NUCLEO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Stack of two X-NUCLEO boards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Jumper connection of X-NUCLEO-ISO1A1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 LED indication pattern during normal board operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 X-NUCLEO-ISO1A1 circuit schematic (1 of 4). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 X-NUCLEO-ISO1A1 circuit schematic (2 of 4). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 X-NUCLEO-ISO1A1 circuit schematic (3 of 4). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 X-NUCLEO-ISO1A1 circuit schematic (4 of 4). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Digital Input and Digital Output Implementation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

UM3483 – Rev 1

paj 30/31

UWM 3483
TSEEM CEEB CEEB TOOM NYEEM CEEB TOOM STMicroelectronics NV thiab nws cov chaw ua haujlwm (“ST”) muaj cai hloov pauv, kho, txhim kho, hloov kho, thiab kev txhim kho rau cov khoom ST thiab / lossis cov ntaub ntawv no txhua lub sijhawm yam tsis muaj ntawv ceeb toom. Cov neeg yuav khoom yuav tsum tau txais cov ntaub ntawv tseem ceeb ntawm ST cov khoom ua ntej muab xaj. ST cov khoom raug muag raws li ST cov nqe lus thiab cov xwm txheej ntawm kev muag khoom nyob rau hauv qhov chaw thaum lub sijhawm lees paub kev txiav txim. Cov neeg yuav khoom tsuas yog lub luag haujlwm rau kev xaiv, xaiv, thiab siv cov khoom ST thiab ST xav tias tsis muaj kev lav phib xaub rau daim ntawv thov kev pab lossis kev tsim khoom ntawm cov neeg yuav khoom. Tsis muaj daim ntawv tso cai, qhia lossis qhia, rau txhua txoj cai kev txawj ntse tau tso cai los ntawm ST ntawm no. Kev muag khoom ntawm ST nrog cov kev cai sib txawv ntawm cov ntaub ntawv tau teev tseg hauv no yuav tsis muaj kev lav phib xaub los ntawm ST rau cov khoom no. ST thiab ST logo yog cov cim lag luam ntawm ST. Yog xav paub ntxiv txog ST cov cim lag luam, xa mus rau www.st.com/trademarks. Tag nrho lwm yam khoom lossis kev pabcuam npe yog cov cuab yeej ntawm lawv cov tswv. Cov ntaub ntawv hauv daim ntawv no hloov pauv thiab hloov cov ntaub ntawv yav dhau los uas tau muab rau hauv ib qho ua ntej ntawm daim ntawv no.
© 2025 STMicroelectronics All rights reserved

UM3483 – Rev 1

paj 31/31

Cov ntaub ntawv / Cov ntaub ntawv

ST STM32 Industrial Input Output Expansion Board [ua pdf] Tus neeg siv phau ntawv
UM3483, CLT03-2Q3, IPS1025H, STM32 Industrial Input Output Expansion Board, STM32, Industrial Input Output Expansion Board, Input Output Expansion Board, Output Expansion Board, Expansion Board

Cov ntaub ntawv

Cov neeg siv phau ntawv

STM32 Industrial Input Output Expansion Board User Manual

STM32 Industrial Input Output Expansion Board

Specifications:

Cov lus qhia siv khoom:

Dual-channel Digital Isolator (STISO620 and STISO621):

High-side Switches (IPS1025H-32 and IPS1025HQ-32):

High-side Current Limiter (CLT03-2Q3):

FAQ:

Q: What should I do if the side switches get heated?

Q: What do the LEDs on the board indicate?

Cov ntaub ntawv / Cov ntaub ntawv

Cov ntaub ntawv

Cia ib saib

Ncua tseg teb