M5STACK StamPLC IoT Mai Kula da Logic Mai Shirye-shiryen

Ƙayyadaddun bayanai

Ƙayyadaddun bayanai	Siga
Module Sarrafa	StampS3A contro1 module, dangane da ESP32-S3FN8, ya hada da 8MB Flash, 2.4GHz Wi-Fi, Bluetooth Low Energy (BLE)
FLASH	8MB
Abubuwan Shiga na Dijital	Tashoshi 8 na abubuwan da aka keɓe na dijital na opto, shigarwa voltage kewayon: DC 5 ~ 36V
Dijital 0 fitarwa	4-tashoshi relay fitarwa
Relays	AC 5A@250V, DC 5A@28V
DC Mai ba da wutar lantarki	yana goyan bayan DC 6 ~ 36V@1A faffadan voltage wadata, DC wutar lantarki: DC5521 mace, 5.5x 2.1mm (tsakiyar-tabbatacce) Fadada
n Interfaces	GPIO.EXT dubawa,2 Grove musaya
Hanyoyin Sadarwa	Kan jirgin PWR-CAN da PWR-485 musaya
PWR-CAN Interface	XT30(2+2)PW-M
Bayanan Bayani na PWR-485	HT3.96-4P
Nunawa	1.14-inch launi nuni (135 × 240 ƙuduri), wanda ST7789v2 guntu ke jagoranta
Contro1 &Mu'amala	1 RESET/B00T maballin, maɓallan mai amfani 3, buzzer
Adana Bayanai	Gina-in Micro SD katin Ramin
Sensors	LM75 zafin jiki firikwensin,INA226 voltage/ na yanzu firikwensin,RTC(RX8130CE)
I/0 Ƙarfin Load da Port	2 × 8 fadada dubawa: matsakaicin ƙarfin 1oad DC 4.76V @ 700mA, Grove tashar jiragen ruwa 1oad iya aiki: DC 4.81V e 700mA
Amfanin Wuta	Aiki na yanzu: (5V supp1y)DC 5V@21.60mA,(12V wadata)DC 12Ve15.22mA;Aiki na yanzu:(5V wadata)DC 5Ve93.89mA, (12V wadata)DC 12V@47.84mA
Hanyar shigarwa	DIN dogo hawa
Yanayin Aiki	-10 ~ 50 ° C
Girman samfur	72.0×80.0×31.7mm
Nauyin samfur	139.4 g
Girman Kunshin	102.0 x 94.0 x 37mm
Cikakken nauyi	163.7 g
Mai ƙira	M5Stack Technology Co., Ltd Block A10, Expo Bay South Coast, Fuhai Street, gundumar Bao'an, Shenzhen, China
Matsakaicin adadin CE	2.4G Wi-Fi: 2412-2472MHz/2422-2462MHz BLE: 2402-2480MHz
Matsakaicin EIRP na CE	Saukewa: 6.84dBm 2.4G Wi-Fi: 17.90dBm

Umarnin Amfani da samfur

Saurin Farawa
Don farawa da Stam PLC, bi waɗannan matakan:

SCAN Wi-Fi

1. Wutar lantarki a kan Stam PLC ta amfani da wutar lantarki da aka bayar na DC.
2. Danna maɓallin SAKESET/BOOT don fara na'urar.
3. Samun dama ga saitunan Wi-Fi akan na'urarka kuma duba samammun cibiyoyin sadarwa.
4. Zaɓi cibiyar sadarwar Wi-Fi da ta dace kuma shigar da kalmar wucewa idan an buƙata.
5. Da zarar an haɗa, zaku iya fara amfani da damar sadarwar mara waya ta Stam PLC.

SCAN BLE

1. Tabbatar cewa Stam PLC ya kunna kuma yana aiki.
2. Kunna saitunan Bluetooth akan na'urarka.
3. Bincika don samun na'urorin Bluetooth a kusa.
4. Zaɓi Stam PLC daga jerin na'urorin da aka gano don kafa haɗin BLE.
5. Yanzu zaku iya yin amfani da ayyukan BLE don canja wurin bayanai da sarrafawa.

BAYANI

Stam PLC shine mai sarrafa dabaru na IoT wanda aka ƙera don sarrafa masana'antu da saka idanu mai nisa. Samfurin yana dogara ne akan StampS3A tsarin sarrafawa, wanda ba wai kawai yana ba da damar sarrafawa mai ƙarfi ba amma kuma yana ba da ingantaccen haɗin kai mara waya. Dangane da sarrafawa, Stam PLC yana ba da bayanai na dijital 8 keɓaɓɓen opto da abubuwan fitarwa na 4 (mai goyan bayan nauyin AC da DC), tare da
GPIO.EXT tashar jiragen ruwa da 2 Grove musaya, yin haɗin kai na daban-daban na'urori masu auna sigina da actuators duka biyu sauki da kuma abin dogara. A halin yanzu, ta hanyar musaya na PWR-CAN da PWR-485, ana iya haɗa na'urar ba tare da ɓata lokaci ba cikin cibiyoyin sadarwa na filayen masana'antu, yana ba da damar watsa bayanai mai nisa da sarrafawa ta tsakiya.

Don hulɗar na'ura da na'ura, samfurin yana nuna nunin launi na 1.14-inch, maɓallin RESET / BOOT, maɓallan mai amfani 3, da buzzer, wanda ke sauƙaƙe daidaitawar ma'auni na lokaci-lokaci da kuma kula da matsayi, kuma zai iya faɗakar da masu amfani a cikin abubuwan da suka faru. Don jure matsanancin yanayin masana'antu, Stam PLC yana goyan bayan faffadan voltage shigarwar (DC 6-36V) kuma an tsara shi don hawan dogo na DIN don tabbatar da shigarwa mai tsaro; Ramin katin Micro SD da aka gina a ciki yana ƙara sauƙaƙe ajiyar bayanai da sabunta firmware.

Bugu da ƙari, tsarin sa ido kan muhalli ya haɗa na'urar firikwensin zafin jiki na LM75 da INA226 voltage/ firikwensin na yanzu don amsawa na ainihin-lokaci akan aikin na'ura, yayin da tsarin RTC (RX8130CE) yana tabbatar da ingantaccen aiki tare da lokaci da rikodi. Firmware na masana'anta ta atomatik yana loda bayanai zuwa dandamalin girgije na M5's EZDATA, yana samar da shafukan sa ido da baiwa masu amfani dacewa da damar isa ga girgije mai nisa da sarrafawa. Wannan samfurin ya dace da sarrafa kansa na masana'antu, saka idanu mai nisa, masana'anta mai wayo, da sauran aikace-aikace.

Stam PLC girma

Hanyoyin Sadarwa

• Babban Mai Gudanarwa: ESP32-S3FN8 (StampS3A sarrafawa module)
• Sadarwar Mara waya: Wi-Fi (2.4 GHz) da Ƙarfin Ƙarfi na Bluetooth (BLE)
• CAN Bus: Kan jirgin PWR-CAN ke dubawa don ingantaccen sadarwar bayanan masana'antu, RS-485:
• Kan jirgin PWR-485 dubawa yana goyan bayan iko mai nisa ta hanyar Modbus RTU yarjejeniya

Processor da Performance

• Samfurin sarrafawa: Xtensa LX7 dual-core (ESP32-S3FN8)
• Ajiya Ajiya: 8MB Flash
• Mitar Aiki: Har zuwa 240 MHz akan microprocessor 32-bit LX7 dual-core

Nuni da Shigarwa

• Nuni: 1.14-inch launi TFT nuni don saka idanu na ainihin lokaci
• Maɓallai: 1 SAKESET/BOOT button da maɓallan mai amfani 3 don sarrafawa da daidaitawa. Buzzer:
• Gina-ginen buzzer don faɗakarwar sauti da sanarwa
• RGB LED: Haɗin RGB LED don ra'ayin gani mai ƙarfi

Fil na GPIO da Matsalolin Tsare-tsare

• GPIO Fil: Yana ba da fitilun GPIO masu daidaitawa da yawa (cikakken taswira da ake samu a cikin takardu)
• Faɗakarwar Interface:
  • 2 Grove musaya don sauƙin firikwensin firikwensin da haɗin mai kunnawa
  • GPIO.EXT dubawa don ƙarin haɗin kai
  • Ramin katin SD Micro don adana bayanai da sabunta firmware

Wasu

• Hannun Hannun Kan Jirgin: Mai haɗa nau'in-C don shirye-shirye, samar da wutar lantarki, da sadarwar serial
• Girman Jiki: 72.0 × 80.0 × 31.7 mm tare da ƙirar dogo na DIN, wanda ya dace da yanayin masana'antu masu tsauri
• Shigar da Wuta: Faɗin voltage shigar da ke jere daga DC 6-36V
• Haɗin firikwensin: Ya haɗa da firikwensin zafin jiki na LM75, INA226 voltage/na firikwensin halin yanzu, da RTC (RX8130CE) don daidaitaccen aiki tare na lokaci da rikodi
• Fitowar Relay: Abubuwan watsawa ta tashar 4-tashoshi masu goyan bayan AC 5A @ 250V / DC 5A @ 28V Matsalolin Dijital mai Warewa: Tashoshi 8 da aka tsara don tallafawa abubuwan shigar DC 5-36V don amintaccen sigina acq

Girman Module

SAURAN FARA

Kafin ka yi wannan matakin, duba rubutun a shafi na ƙarshe: Sanya Arduino.

Buga bayanan WiFi

1. Bude Arduino IDE (Duba zuwa https://docs.m5stack.com/en/arduino/arduino_ide don jagorar shigarwa don hukumar haɓakawa da software)
2. Zaɓi allon ESP32S3 DEV Module da tashar tashar da ta dace, sannan loda lambar.e
3. Bude serial Monitor don nuna Wi-Fi da aka bincika da bayanin ƙarfin sigina.

SAURAN FARA
Kafin kayi wannan matakin, duba rubutun da ke cikin shafi na ƙarshe: Sanya Arduin.

Buga bayanan BLE

1. Bude Arduino IDE (Duba zuwa https://docs.m5stack.com/en/arduino/arduino_ide don jagorar shigarwa don hukumar haɓakawa da software)
2. Zaɓi allon ESP32S3 DEV Module da tashar tashar da ta dace, sannan loda lambar.
3. Bude serial Monitor don nuna BLE da aka bincika da kuma bayanan ƙarfin sigina.

Gargadi na FCC

FCC Tsanaki:
Duk wani canje-canje ko gyare-gyaren da ƙungiyar da ke da alhakin bin doka ba ta amince da su ba na iya ɓata ikon mai amfani na sarrafa kayan aiki.
Wannan na'urar ta bi sashe na 15 na Dokokin FCC.

Aikin yana ƙarƙashin sharuɗɗa biyu masu zuwa:

1. Wannan na'urar bazai haifar da tsangwama mai cutarwa ba, kuma
2. Dole ne wannan na'urar ta karɓi duk wani tsangwama da aka karɓa, gami da tsangwama wanda zai iya haifar da aiki maras so.

MUHIMMAN NOTE:

Lura: An gwada wannan kayan aikin kuma an same shi don biyan iyaka don na'urar dijital ta Class B, bisa ga sashi na 15 na Dokokin FCC. An ƙirƙira waɗannan iyakokin don ba da kariya mai ma'ana daga tsangwama mai cutarwa a cikin shigarwar mazauni. Wannan kayan aiki yana haifarwa, amfani, kuma yana iya haskaka ƙarfin mitar rediyo kuma, idan ba'a shigar da shi ba kuma ana amfani dashi daidai da umarnin, yana iya haifar da tsangwama mai cutarwa ga sadarwar rediyo. Duk da haka, babu tabbacin cewa tsangwama ba zai faru a cikin wani shigarwa na musamman ba.

Idan wannan kayan aikin ya haifar da tsangwama mai cutarwa ga liyafar rediyo ko talabijin, wanda za'a iya tantancewa ta hanyar kashe kayan aiki da kunnawa, ana ƙarfafa mai amfani da yayi ƙoƙarin gyara tsangwama ta hanyar ɗaya ko fiye na waɗannan matakan:

• Sake daidaitawa ko matsar da eriya mai karɓa.
• Ƙara rabuwa tsakanin kayan aiki da mai karɓa.
• Haɗa kayan aiki zuwa wani mashigar da ke kewaye daban da wanda aka haɗa mai karɓa zuwa gare shi.
• Tuntuɓi dila ko gogaggen masanin rediyo/TV don taimako.

Bayanin Bayyanar Radiation FCC

Wannan kayan aikin ya dace da iyakokin fiddawa na FCC da aka tsara don yanayin da ba a sarrafa shi ba. Ya kamata a shigar da wannan kayan aikin tare da mafi ƙarancin nisa na 20cm tsakanin radiyo da jikin ku.

Arduino Shigar

Shigar da Arduino IDE(https://www.arduino.cc/en/Main/Software)

Danna don ziyartar jami'in Arduino website, kuma zaɓi kunshin shigarwa don tsarin aikin ku don saukewa.

Shigar da Gudanarwar Hukumar Arduino

1. Manajan Hukumar URL ana amfani da shi don lissafta bayanan hukumar haɓaka don takamaiman dandamali. A cikin Arduino IDE menu, zaɓi File -> Abubuwan da ake so
2. Kwafi gudanarwar hukumar ESP URL kasa cikin Ƙarin Hukumar Gudanarwa URLs filin, kuma ajiye. https://espressif.github.io/arduino-esp32/package_esp32_dev_index.json
3. A cikin labarun gefe, zaɓi Manajan Hukumar, bincika ESP, kuma danna Shigar.
4. A cikin labarun gefe, zaɓi Manajan allo, bincika M5Stack, sannan danna Shigar.
   Dangane da samfurin da aka yi amfani da shi, zaɓi allon haɓaka daidai a ƙarƙashin Kayan aiki -> Board -> M5Stack -> {ESP32S3 DEV Module Board}.
5. Haɗa na'urar zuwa kwamfutarka tare da kebul na bayanai don loda shirin.

Tambayoyin da ake yawan yi

Menene shawarar aiki voltagMenene rabon da Stam PLC ya biya?

Shawarar aiki voltage yana tsakanin DC 6V zuwa 36V tare da samar da 1A na yanzu. Tabbatar yin amfani da wutar lantarki mai dacewa da DC don ingantaccen aiki.

Ta yaya zan iya faɗaɗa ayyukan Stam PLC?

Kuna iya faɗaɗa aikin ta amfani da fil ɗin GPIO da ƙarin mu'amala da aka bayar. Haɗa na'urori masu auna firikwensin da masu kunnawa zuwa mu'amalar Grove don ingantattun iyakoki.

Takardu / Albarkatu

M5STACK StamPLC IoT Mai Kula da Logic Mai Shirye-shiryen [pdf] Jagorar mai amfani StamPLC IoT Mai Kula da Logic Mai Gudanarwa, IoT Mai Kula da Mahimmanci, Mai Sarrafa Ma'auni, Mai sarrafa dabaru

Magana

• Manual mai amfani