I-M5STACK yaseStamPLC IoT Programmable Logic Controller
Iinkcukacha
| Inkcazo | Ipharamitha |
| Imodyuli yokulawula | StampImodyuli ye-S3A contro1, esekwe kwi-ESP32-S3FN8, ibandakanya i-8MB Flash, i-2.4GHz Wi-Fi, iBluetooth Low Energy (BLE) |
| IFLESHI | 8MB |
| Iingeniso zeDijithali | Iitshaneli ezi-8 ze-opto-isolated digital inputs, igalelo voltaguluhlu e: DC 5 ~ 36V |
| Iziphumo zeDigital | I-4-channel relay iziphumo |
| IiRelay | AC 5A@250V,DC 5A@28V |
| Ukunikezelwa kwamandla kwiDC | ixhasa i-DC 6 ~ 36V@1A ivolumu ebanzitagi-e supply, DC ikona yombane:DC5521 female,5.5x 2.1mm(kumbindi-positive) Ukwandiswa |
| n Ujongano | GPIO.EXT interface,2 Grove interfaces |
| IiNxibelelwano zoNxibelelwano | Kwibhodi ye-PWR-CAN kunye ne-PWR-485 ujongano |
| PWR-CAN Interface | XT30(2+2)PW-M |
| PWR-485 ujongano | HT3.96-4P |
| Bonisa | 1.14-intshi ebonisa umbala (135 × 240 isisombululo), eqhutywa yi-ST7789v2 chip |
| I-Contro1 &Nentsebenziswano | I-1 RESET/B00T iqhosha, amaqhosha omsebenzisi ama-3, i-buzzer |
| Ukugcinwa kwedatha | Eyakhelwe kwi-Micro SD ikhadi slot |
| Izivamvo | LM75 inzwa yobushushu, INA226 voltagi-e/inzwa yangoku,RTC(RX8130CE) |
| I/0 kwiPort Load Capacity | I-2 × 8 i-interface yokwandisa: ubuninzi be-1oad umthamo we-DC 4.76V @700mA, i-Grove port 1oad umthamo: DC 4.81V e 700mA |
| Ukutya umbane | Umsinga omileyo:(5V supp1y)DC 5V@21.60mA,(12V ubonelelo)DC 12Ve15.22mA;Operating current:(5V supply)DC 5Ve93.89mA, (12V supply)DC 12V@47.84mA |
| Indlela yokuFakela | DIN kaloliwe ukunyuswa |
| Ubushushu bokusebenza | -10~50°C |
| Imilinganiselo yeMveliso | 72.0×80.0×31.7mm |
| Ubunzima bemveliso | 139.4g |
| Iipakethi Imilinganiselo | 102.0x94.0 x 37mm |
| Ubunzima bokuqala | 163.7g |
| Umenzi | IM5Stack Technology Co., Ltd
Block A10, Expo Bay South Coast, Fuhai Street, Bao'an District, Shenzhen, China |
| Uluhlu lokuphindaphinda kwi-CE | 2.4G Wi-Fi: 2412-2472MHz/2422-2462MHz BLE: 2402-2480MHz |
| Ubuninzi be-EIRP ye-CE | I-BLE: 6.84dBm
2.4G Wi-Fi: 17.90dBm |
Imiyalelo yokusetyenziswa kwemveliso
Ukuqalisa ngokukhawuleza
Ukuqalisa ngeStam PLC yakho, landela la manyathelo:
SKENZA iWi-Fi
- Umbane kwiStam PLC usebenzisa unikezelo lwamandla olubonelelweyo lweDC.
- Cinezela i-RESET/BOOT iqhosha ukuqalisa isixhobo.
- Fikelela kwiisetingi zeWi-Fi kwisixhobo sakho kwaye ujonge iinethiwekhi ezikhoyo.
- Khetha inethiwekhi ye-Wi-Fi efanelekileyo kwaye ufake igama lokugqitha ukuba liyafuneka.
- Nje ukuba uqhagamshelwe, ungaqala ukusebenzisa amandla onxibelelwano ngaphandle kwamacingo eStam PLC.
SKENA BLE
- Qinisekisa ukuba iStam PLC iyasebenza kwaye iyasebenza.
- Vula useto lweBluetooth kwisixhobo sakho.
- Skena izixhobo zeBluetooth ezifumanekayo kwindawo.
- Khetha iStam PLC kuluhlu lwezixhobo ezifunyenweyo ukuseka uqhagamshelo lwe-BLE.
- Ngoku ungasebenzisa ukusebenza kwe-BLE kugqithiso lwedatha kunye nolawulo.
UMXHOLO
I-Stam PLC sisilawuli se-IoT esicwangcisiweyo se-IoT eyenzelwe ukuzenzekelayo kwimizi-mveliso kunye nokubeka iliso kude. Imveliso isekelwe kwiStampImodyuli yolawulo ye-S3A, enganikezeli kuphela amandla okusebenza anamandla kodwa ikwabonelela ngokuqhagamshelwa ngaphandle kwamacingo. Ngokolawulo, iStam PLC ibonelela nge-8 opto-isolated inputs digital kunye ne-4 relay iziphumo (ezixhasa zombini imithwalo ye-AC kunye ne-DC), kunye
I-GPIO.EXT port kunye ne-2 Grove interfaces, eyenza ukuhlanganiswa kweenzwa ezahlukeneyo kunye ne-actuators zombini zilula kwaye zithembekileyo. Okwangoku, nge-onboard PWR-CAN kunye ne-PWR-485 ujongano, isixhobo sinokudityaniswa ngokungenamthungo kuthungelwano lwe-industrial fieldbus, evumela ukuhanjiswa kwedatha okude kunye nolawulo oluphakathi.
Ukusebenzisana komatshini womntu, umkhiqizo ubonisa umbala we-1.14-intshi, iqhosha le-RESET / BOOT, amaqhosha omsebenzisi we-3, kunye ne-buzzer, eququzelela ukucwangciswa kwepharamitha yexesha langempela kunye nokubeka iliso kwimeko, kwaye inokulumkisa abasebenzisi xa kwenzeka izinto ezingaqhelekanga. Ukumelana nokusingqongileyo kwemizi mveliso, iStam PLC ixhasa ivolthi ebanzitagigalelo le-e (DC 6–36V) kwaye yenzelwe ukunyuswa kukaloliwe weDIN ukuqinisekisa ukufakela okukhuselekileyo; i-Micro SD khadi slot eyakhelwe-ngaphakathi iququzelela ngakumbi ukugcinwa kwedatha kunye nohlaziyo lwe-firmware.
Ukongeza, inkqubo yayo yokubeka iliso kwendalo idibanisa inzwa yobushushu be-LM75 kunye ne-INA226 voltage / inzwa yangoku yempendulo yexesha langempela ekusebenzeni kwesixhobo, ngelixa imodyuli ye-RTC (RX8130CE) iqinisekisa ukuvumelanisa ixesha elichanekileyo kunye nokurekhoda kwelogi. I-firmware yefektri ilayisha ngokuzenzekelayo idatha kwi-M5's EZDATA cloud platform, ivelisa amaphepha okubeka iliso kwaye inike abasebenzisi ukufikelela kunye nokulawula ifu elikude. Le mveliso ifanelekile kwimizi-mveliso ezenzekelayo, ukujonga kude, ukuvelisa ngobuchule, kunye nezinye izicelo.
Stam PLC
Ubunakho boNxibelelwano
- UMlawuli oyiNtloko: ESP32-S3FN8 (eStampImodyuli yolawulo ye-S3A)
- Unxibelelwano olungenazingcingo: Wi‑Fi (2.4 GHz) kunye neBluetooth yaMandla aPhantsi (BLE)
- Ibhasi ye-CAN: I-onboard PWR-CAN ujongano lonxibelelwano oluthembekileyo lwedatha yeshishini, RS-485:
- I-onboard PWR-485 interface exhasa ulawulo olude ngeModbus RTU protocol
Iprosesa kunye nokuSebenza
- Umzekelo weProsesa: Xtensa LX7 dual-core (ESP32-S3FN8)
- Umthamo wokuGcina: 8MB Flash
- Umza wokuSebenza: Ukuya kuthi ga kwi-240 MHz kwi-dual-core 32-bit LX7 microprocessor
Umboniso kunye noNgeniso
- Bonisa: 1.14‑ intshi yombala we-TFT umboniso wokubeka iliso kwiparamitha yexesha lokwenyani
- Amaqhosha: 1 RESET/BOOT iqhosha kunye namaqhosha omsebenzisi ama-3 olawulo kunye noqwalaselo. Buzzer:
- I-buzzer eyakhelwe-ngaphakathi kwizilumkiso zomsindo kunye nezaziso
- I-RGB ye-LED: I-RGB ye-LED edibeneyo yempendulo ebonakalayo ebonakalayo
Izikhonkwane ze-GPIO kunye ne-Programmable Interfaces
- Izikhonkwane zeGPIO: Ibonelela ngezikhonkwane ezininzi zeGPIO ezilungiselelwayo (imephu eneenkcukacha ekhoyo kumaxwebhu)
- Ukwandiswa kweNdibaniselwano:
- 2 Ujongano lweGrove lwenzwa elula kunye noqhagamshelo lwe-actuator
- I-GPIO.EXT ujongano loqhagamshelwano olongezelelweyo
- I-Micro SD khadi slot yokugcina idatha kunye nohlaziyo lwe-firmware
Abanye
- I-Onboard Interfaces: Isidibanisi sohlobo-C lwenkqubo, ubonelelo lwamandla, kunye nonxibelelwano olulandelelanayo
- Ubungakanani bomzimba: 72.0 × 80.0 × 31.7 mm kunye neDIN yoyilo lokunyuswa kukaloliwe, ilungele imeko yeshishini elibi
- Igalelo laMandla: Umthamo obanzitage igalelo ukusuka DC 6–36V
- Ii-Sensors ezidibeneyo: Iquka i-LM75 inzwa yeqondo lokushisa, i-INA226 voltagi-e/sensor yangoku, kunye ne-RTC (RX8130CE) yokuvumelanisa ixesha elichanekileyo kunye nokurekhoda kwelogi
- I-Relay Outputs: I-4-channel relay iziphumo ezixhasa i-AC 5A @ 250V / DC 5A @ 28V Igalelo leDijithali ye-Opto-Isolated: Iitshaneli ezi-8 ezenzelwe ukuxhasa i-DC 5-36V igalelo le-acq yesiginali ekhuselekileyo
Ubungakanani bemodyuli
UKUQALA NGOKUKHAWULEZA
Ngaphambi kokuba wenze eli nyathelo, jonga isicatshulwa kwisihlomelo sokugqibela: Ukufakela iArduino.
Shicilela ulwazi lwe-WiFi
- Vula i-Arduino IDE (Jonga ku https://docs.m5stack.com/en/arduino/arduino_ide kwisikhokelo sofakelo sebhodi yophuhliso kunye nesoftware)
- Khetha ibhodi yeModyuli ye-ESP32S3 DEV kunye ne-port ehambelanayo, uze ulayishe ikhowudi.e
- Vula i-serial monitor ukuze ubonise i-WiFi eskeniweyo kunye nolwazi lwamandla omqondiso.
UKUQALA NGOKUKHAWULEZA
Phambi kokuba wenze eli nyathelo, jonga isicatshulwa esikwisihlomelo sokugqibela: Ukufakela iArduin.
Shicilela ulwazi lweBLE
- Vula i-Arduino IDE (Jonga ku https://docs.m5stack.com/en/arduino/arduino_ide kwisikhokelo sofakelo sebhodi yophuhliso kunye nesoftware)
- Khetha ibhodi yeModyuli ye-ESP32S3 kunye ne-port ehambelanayo, uze ulayishe ikhowudi.
- Vula i-serial monitor ukuze ubonise i-BLE eskeniweyo kunye nolwazi lwamandla omqondiso.
Isilumkiso seFCC
Isilumkiso seFCC:
Naluphi na uTshintsho okanye uhlengahlengiso olungavunywanga ngokucacileyo liqela elinoxanduva lokuthotyelwa lunokuphelisa igunya lomsebenzisi lokusebenzisa isixhobo.
Esi sixhobo sithobela inxalenye ye-15 yeMithetho yeFCC.
Umsebenzi uxhomekeke kwezi meko zimbini zilandelayo:
- Esi sixhobo asinakubanga uphazamiseko oluyingozi, kunye
- Esi sixhobo kufuneka samkele naluphi na uphazamiseko olufunyenweyo, kubandakanywa uphazamiseko olunokubangela ukusebenza okungafunekiyo.
INQAKU ELIBALULEKILEYO:
Phawula: Esi sixhobo sivavanyiwe saza safunyanwa ukuba sithobela imida yesixhobo sedijithali soDidi B, ngokungqinelana nenxalenye ye-15 yeMithetho yeFCC. Le mida yenzelwe ukubonelela ngokhuseleko olufanelekileyo ekuphazamisekeni okunobungozi kwindawo yokuhlala. Esi sixhobo sivelisa, sisebenzisa, kwaye sinokusasaza amandla erediyo yerediyo kwaye, ukuba asifakanga kwaye sisetyenziswa ngokuhambelana nemiyalelo, sinokubangela uphazamiseko oluyingozi kunxibelelwano lwerediyo. Nangona kunjalo, akukho siqinisekiso sokuba ukuphazamiseka akuyi kwenzeka kufakelo oluthile.
Ukuba esi sixhobo sibangela uphazamiseko oluyingozi kunomathotholo okanye ulwamkelo lukamabonakude, olunokumiselwa ngokucinywa nokulayita isixhobo, umsebenzisi uyakhuthazwa ukuba azame ukulungisa uphazamiseko ngenye okanye ngaphezulu kwezi ndlela zilandelayo:
- Jongisa kwakhona okanye uhambise i-eriyali efumanayo.
- Yandisa ukwahlukana phakathi kwesixhobo kunye nomamkeli.
- Qhagamshela izixhobo kwindawo yokuphuma kwisekethe eyahlukileyo kuleyo apho umamkeli aqhagamshelwe khona.
- Dibana nomthengisi okanye igcisa likanomathotholo/kumabonakude ukuze ufumane uncedo.
INkcazelo yokuVela kwiMitha yeFCC
Esi sixhobo sithobela imida yokuvezwa kwemitha yeFCC emiselwe indawo engalawulwayo. Esi sixhobo kufuneka sifakwe kwaye sisebenze kumgama ongaphantsi wama-20cm phakathi kweradiyetha nomzimba wakho.
Faka iArduino
Ukuhlohla i-Arduino IDE(https://www.arduino.cc/en/Main/Software)
Cofa ukutyelela igosa leArduino webindawo, kwaye ukhethe ipakethe yokuhlohla ukuze ukhuphele inkqubo yakho yokusebenza.
Ukufakela uLawulo lweBhodi yeArduino
- UMphathi weBhodi URL isetyenziselwa isalathisi solwazi lwebhodi yophuhliso lweqonga elithile. Kwimenyu ye-Arduino IDE, khetha File -> Ezikhethwayo
- Kopa ulawulo lwebhodi ye-ESP URL ngezantsi kuMphathi weBhodi owongezelelweyo URLs intsimi, kwaye ugcine. https://espressif.github.io/arduino-esp32/package_esp32_dev_index.json
- Kwibar esecaleni, khetha uMphathi weBhodi, khangela i-ESP, kwaye ucofe Faka.
- Kwibar esecaleni, khetha uMphathi weBhodi, khangela iM5Stack, kwaye ucofe Faka.
Ngokuxhomekeke kwimveliso esetyenzisiweyo, khetha ibhodi yophuhliso ehambelanayo phantsi kweZixhobo -> Ibhodi -> M5Stack -> {ESP32S3 DEV Module board}.
- Qhagamshela isixhobo kwikhompyuter yakho ngentambo yedatha ukulayisha inkqubo.
Imibuzo ebuzwa qho
Uthini umthamo wokusebenza ocetyiswayotage ye Stam PLC?
Umthamo wokusebenza ocetyiswayotage iphakathi kwe-DC 6V ukuya kwi-36V kunye nobonelelo lwangoku lwe-1A. Qinisekisa ukusebenzisa unikezelo lwamandla oluhambelanayo lwe-DC ukuze usebenze kakuhle.
Ndinokwandisa njani ukusebenza kweStam PLC?
Unokwandisa ukusebenza ngokusebenzisa izikhonkwane zeGPIO kunye nojongano olongezelelweyo olunikiweyo. Qhagamshela abenzi boluvo kunye nee-activators kwi-interface yeGrove ukuze uphucule amandla.
Amaxwebhu / Izibonelelo
 |
I-M5STACK yaseStamPLC IoT Programmable Logic Controller [pdf] Isikhokelo somsebenzisi StamPI-LC IoT iProgrammable Logic Controller, i-IoT Programmable Logic Controller, isiLawuli seNgcaciso eCwangcisiweyo, isiLawuli seNgcaciso |