M5STACK StamPLC IoT Ntuziaka Onye njikwa Logic Programmable

Nkọwapụta	Oke
Modul njikwa	StampS3A contro1 modul, dabere na ESP32-S3FN8, gụnyere 8MB Flash, 2.4GHz Wi-Fi, Bluetooth Low Energy (BLE)
FLASH	8MB
Ntinye dijitalụ	Ọwa 8 nke ntinye dijitalụ dịpụrụ adịpụ opto, ntinye voltage nso: DC 5 ~ 36V
Ntinye dijitalụ 0	4-ọwa relay mmepụta
Relays	AC 5A@250V,DC 5A@28V
DC Power Tụkwasịnụ	na-akwado DC 6~36V@1A obosara voltage ọkọnọ, DC ike cornector: DC5521 nwanyị, 5.5x 2.1mm (etiti-mma) Mgbasawanye
n Interface	GPIO.EXT interface,2 Grove interfaces
Nkwukọrịta ozi	Onboard PWR-CAN na PWR-485 interfaces
PWR-CAN Interface	XT30(2+2)PW-M
PWR-485 interface	HT3.96-4P
Ngosipụta	Ngosipụta agba 1.14 inch (mkpebi 135 × 240), nke mgbawa ST7789v2 na-anya.
Contro1 & Mmekọrịta	1 RESET/B00T bọtịnụ, bọtịnụ onye ọrụ 3, buzzer
Nchekwa data	Oghere kaadị Micro SD arụnyere n'ime ya
Ihe mmetụta	Ihe mmetụta okpomọkụ LM75,INA226 voltage/ ihe mmetụta ugbu a, RTC (RX8130CE)
I/0 Ike Ibu Ibu Port	2 × 8 mgbasawanye interface: kacha 1oad ikike DC 4.76V @ 700mA, Grove ọdụ ụgbọ mmiri 1oad ikike: DC 4.81V e 700mA
Oriri ike	Njikere ugbu a: (5V supp1y)DC 5V@21.60mA,(12V ọkọnọ)DC 12Ve15.22mA; Na-arụ ọrụ ugbu a:(5V ọkọnọ)DC 5Ve93.89mA, (12V ọkọnọ)DC 12V@47.84mA
Usoro ntinye	DIN ụgbọ okporo ígwè arịọnụ
Okpomọkụ na-arụ ọrụ	-10 ~ 50 Celsius
Akụkụ ngwaahịa	72.0×80.0×31.7mm
Ibu ngwaahịa	139.4g
Akụkụ ngwugwu	102.0 x 94.0 x 37mm
Mkpokọta nha	163.7g
Onye nrụpụta	Ụgwọ nke ụlọ ọrụ M5Stack Technology Co., Ltd Block A10, Expo Bay South Coast, Fuhai Street, Bao'an District, Shenzhen, China
Ugboro ugboro maka CE	2.4G Wi-Fi: 2412-2472MHz/2422-2462MHz BLE: 2402-2480MHz
Oke EIRP maka CE	BLE: 6.84dBm 2.4G Wi-Fi: 17.90dBm

Ntuziaka ojiji ngwaahịa

Mmalite ngwa ngwa
Iji malite Stam PLC gị, soro usoro ndị a:

Nyochaa Wi-Fi

Ike na Stam PLC na-eji ike ọkụ DC enyere.
Pịa bọtịnụ RESET/BOOT ka ịmalite ngwaọrụ ahụ.

Nweta ntọala Wi-Fi dị na ngwaọrụ gị wee nyochaa netwọkụ dị.
Họrọ netwọk Wi-Fi kwesịrị ekwesị wee tinye paswọọdụ ma ọ bụrụ na achọrọ ya.

Ozugbo ejikọrọ, ị nwere ike ịmalite iji ikike nkwurịta okwu ikuku nke Stam PLC.

Nyochaa BLE

Gbaa mbọ hụ na agbanyere Stam PLC ma na-arụ ọrụ.
Mee ka ntọala Bluetooth rụọ ọrụ na ngwaọrụ gị.

Chọgharịa maka ngwaọrụ Bluetooth dị n'akụkụ.
Họrọ Stam PLC na listi ngwaọrụ achọpụtara iji guzobe njikọ BLE.

Ị nwere ike tinye ọrụ BLE ugbu a maka ịnyefe na njikwa data.

MỤTA

Stam PLC bụ njikwa mgbagha mmemme nke IoT emebere maka akpaaka ụlọ ọrụ yana nleba anya anya. Ngwaahịa a dabeere na StampS3A modul njikwa, nke na-abụghị nanị na-enye ike nhazi ike ma na-enye njikọ ikuku nke ọma. N'ihe gbasara njikwa, Stam PLC na-enye ntinye dijitalụ dịpụrụ adịpụ 8 na ntinye relay 4 (na-akwado ma ibu AC na DC), yana
GPIO.EXT ọdụ ụgbọ mmiri na 2 Grove interfaces, na-eme ka njikọ nke sensọ dị iche iche na actuators dị mfe ma bụrụ ndị a pụrụ ịdabere na ya. Ka ọ dị ugbu a, site na onboard PWR-CAN na PWR-485 interfaces, ngwaọrụ nwere ike itinye n'enweghị nsogbu na netwọk fieldbus mmepụta ihe, na-eme ka nnyefe data dịpụrụ adịpụ na njikwa etiti.

Maka mmekọrịta mmadụ na igwe, ngwaahịa ahụ nwere ihe ngosi agba nke 1.14-inch, bọtịnụ RESET / BOOT, bọtịnụ ndị ọrụ 3, na buzzer, nke na-eme ka nhazi nhazi oge na nlekota ọkwa, ma nwee ike mee ka ndị ọrụ mara ihe omume nke anomalies. Iji nagide gburugburu ụlọ ọrụ mmepụta ihe siri ike, Stam PLC na-akwado voltaji sara mbaratage ntinye (DC 6-36V) ma emebere ya maka ntinye ụgbọ okporo ígwè DIN iji hụ na ntinye nchekwa; oghere Micro SD nke etinyere na ya na-eme ka nchekwa data na mmelite firmware dị mfe.

Na mgbakwunye, usoro nleba anya gburugburu ebe obibi ya jikọtara ihe mmetụta okpomọkụ LM75 yana INA226 voltagihe mmetụta e/nke dị ugbu a maka nzaghachi ozugbo na arụ ọrụ ngwaọrụ, ebe modul RTC (RX8130CE) na-ahụ maka mmekọrịta oge ziri ezi na ndekọ ndekọ. Firmware ụlọ ọrụ na-ebugo data na-akpaghị aka na igwe ojii M5 EZDATA, na-emepụta ibe nleba anya ma na-enye ndị ọrụ ohere ịnweta igwe ojii dịpụrụ adịpụ na njikwa. Ngwaahịa a dabara adaba maka akpaaka ụlọ ọrụ, nleba anya anya, nrụpụta smart na ngwa ndị ọzọ.

Ụgwọ nke ụlọ ọrụ Stam PLC

Ike nzikọrịta ozi

Onye njikwa isi: ESP32-S3FN8 (StampS3A akara modul)

Nkwukọrịta ikuku: Wi-Fi (2.4 GHz) na obere ike Bluetooth (BLE)
CAN Bus: Onboard PWR-CAN interface maka nzikọrịta ozi ụlọ ọrụ a pụrụ ịdabere na ya, RS-485:

Onboard PWR-485 interface na-akwado njikwa anya site na Modbus RTU protocol.

Processor na arụmọrụ

Ụdị nhazi: Xtensa LX7 dual-core (ESP32-S3FN8)
Ike nchekwa: 8MB Flash

Ugboro na-arụ ọrụ: Ruo 240 MHz na microprocessor 32-bit LX7 dual-core.

Ngosipụta na ntinye

Ngosipụta: Ngosipụta TFT agba 1.14 inch maka nleba anya oke oge
Bọtịnụ: 1 RESET/BOOT bọtịnụ gbakwunyere bọtịnụ onye ọrụ 3 maka njikwa na nhazi. Buzzer:

Buzzer arụnyere n'ime maka ọkwa ọdịyo na ọkwa
RGB LED: Integrated RGB LED maka nzaghachi anya dị ike

GPIO pins na interface mmemme

GPIO Pins: Na-enye ọtụtụ GPIO ntụtụ nwere ike ịhazi (nkewa nkọwa dị na akwụkwọ)
Ọnụ ụzọ mgbasawanye:
- 2 Grove interfaces maka ihe mmetụta dị mfe na njikọ actuator
- GPIO.EXT interface maka njikọta ọzọ
- Oghere kaadị Micro SD maka nchekwa data na mmelite firmware

Ndị ọzọ

Ọnụ ụzọ ụgbọ mmiri: Njikọ Type-C maka mmemme, ọkọnọ ọkụ na nzikọrịta ozi
Akụkụ anụ ahụ: 72.0 × 80.0 × 31.7 mm nwere atụmatụ DIN rail mount, dabara maka gburugburu ụlọ ọrụ siri ike.
Ntinye ike: Obosara voltage ntinye sitere na DC 6-36V
Ihe mmetụta agbakwunyere: Gụnyere ihe mmetụta okpomọkụ LM75, INA226 voltagihe mmetụta e/ugbu a, yana RTC (RX8130CE) maka ịmekọrịta oge ziri ezi na ndekọ ndekọ.
Nbudata ọsọ ọsọ: 4-channel relay results akwado AC 5A @ 250V / DC 5A @ 28V Opto-kewapụrụ Digital Ntinye: Ọwa 8 emebere iji kwado ntinye DC 5-36V maka mgbama nchekwa acq

Nha modul

Ngwa ngwa ngwa

Tupu ịme usoro a, lelee ederede dị na mgbakwunye ikpeazụ: Ịwụnye Arduino.

Bipụta ozi WiFi

Mepee Arduino IDE (tụ aka https://docs.m5stack.com/en/arduino/arduino_ide maka ntuziaka nrụnye maka bọọdụ mmepe na ngwanrọ)
Họrọ bọọdụ Module ESP32S3 DEV yana ọdụ ụgbọ mmiri kwekọrọ, wee bulite koodu ahụ.e
Mepee ihe nleba anya nsonazụ ka igosipụta WiFi enyochagoro yana ozi ike mgbama.

Ngwa ngwa ngwa
Tupu ịme usoro a, lelee ederede dị na mgbakwunye ikpeazụ: Ịwụnye Arduin.

Bipụta ozi BLE

Mepee Arduino IDE (tụ aka https://docs.m5stack.com/en/arduino/arduino_ide maka ntuziaka nrụnye maka bọọdụ mmepe na ngwanrọ)
Họrọ bọọdụ Module ESP32S3 DEV yana ọdụ ụgbọ mmiri kwekọrọ, wee bulite koodu ahụ.
Mepee ihe nleba anya n'usoro iji gosi ozi ike mgbama BLE enyochagoro.

FCC ịdọ aka ná ntị

Akpachara anya FCC:
Mgbanwe ọ bụla ma ọ bụ mgbanwe ọ bụla nke ndị na-ahụ maka nnabata na-akwadoghị nke ọma nwere ike imebi ikike onye ọrụ iji rụọ ọrụ ahụ.
Ngwaọrụ a na-akwado akụkụ 15 nke Iwu FCC.

A na-arụ ọrụ n'okpuru ọnọdụ abụọ a:

Ngwaọrụ a nwere ike ọ gaghị ebute nnyonye anya na-emerụ ahụ, yana
Ngwaọrụ a ga-anabatarịrị nnyonye anya ọ bụla enwetara, gụnyere nnyonye anya nwere ike ibute ọrụ na-achọghị.

IHE dị mkpa:

Mara: A nwalere ngwa a wee hụ na ọ dabara na oke maka ngwaọrụ dijitalụ Klas B, dịka akụkụ 15 nke Iwu FCC. Emebere oke ndị a iji nye nchebe ezi uche dị na ya megide nnyonye anya na-emerụ emerụ na ntinye ụlọ. Akụrụngwa a na-ewepụta, na-eji, ma nwee ike ịgbasa ike ugboro redio yana, ọ bụrụ na etinyeghị ya ma jiri ya dịka ntuziaka siri dị, nwere ike ibute ndabichi na-emerụ ahụ na nkwukọrịta redio. Agbanyeghị, enweghị nkwa na nnyonye anya agaghị eme na otu nrụnye.

Ọ bụrụ na akụrụngwa a na-ebute nnyonye anya na-emerụ ahụ na nnabata redio ma ọ bụ telivishọn, nke enwere ike ikpebi site na ịgbanyụ ma gbanye akụrụngwa, a na-agba onye ọrụ ume ka ọ nwaa idozi nnyonye anya site na otu ma ọ bụ karịa n'ime usoro ndị a:

Megharịa ma ọ bụ bugharịa antenna nnata.

Mee ka nkewa dị n'etiti akụrụngwa na nnata.
Jikọọ akụrụngwa n'ime oghere na sekit dị iche na nke ejikọrọ onye nnata.
Kpọtụrụ onye na-ere ahịa ma ọ bụ onye ọrụ redio/TV nwere ahụmahụ maka enyemaka.

Nkwupụta Mkpughe Radiation FCC

Ngwa a na-akwado oke ikpughe radieshon FCC nke edobere maka gburugburu ebe anaghị achịkwa ya. Ekwesịrị ịwụnye akụrụngwa a ma rụọ ọrụ ya na opekempe 20cm n'etiti radiator & ahụ gị.

Wụnye Arduino

Ịwụnye Arduino IDE(https://www.arduino.cc/en/Main/Software)

Pịa ileta onye ọrụ Arduino websaịtị, wee họrọ ngwungwu nwụnye maka sistemụ arụmọrụ gị ibudata.

Ịwụnye Arduino Board Management

Onye njikwa Board URL a na-eji iji depụta ozi bọọdụ mmepe maka otu ikpo okwu. Na Arduino IDE menu, họrọ File -> Mmasị
Detuo njikwa bọọdụ ESP URL n'okpuru n'ime Mgbakwunye Board Manager URLs ubi, ma chekwaa. https://espressif.github.io/arduino-esp32/package_esp32_dev_index.json

Na sidebar, họrọ Board Manager, chọọ ESP, wee pịa Wụnye.
Na sidebar, họrọ Board Manager, chọọ M5Stack, wee pịa Wụnye.
Dabere na ngwaahịa ejiri, họrọ bọọdụ mmepe kwekọrọ n'okpuru Ngwaọrụ -> Board -> M5Stack -> {ESP32S3 DEV Moduleboard}.
Jikọọ ngwaọrụ gị na kọmputa na a data USB bulite mmemme.

Ajụjụ a na-ajụkarị

Kedu ihe a na-atụ aro ka arụ ọrụ voltagKedu ihe bụ Stam PLC?

Voltage bụ n'etiti DC 6V ka 36V na a ugbu a ọkọnọ nke 1A. Gbaa mbọ hụ na iji ọkụ ọkụ DC dakọtara maka ịrụ ọrụ kacha mma.

Kedu ka m ga-esi gbasaa ọrụ Stam PLC?

Ị nwere ike ịgbasa ọrụ ahụ site na iji ntụtụ GPIO na oghere ndị ọzọ enyere. Jikọọ sensọ na actuators na oghere Grove maka ike emelitere.

Akwụkwọ / akụrụngwa

M5STACK StamPLC IoT Njikwa Logic Programmable [pdf] Ntuziaka onye ọrụ
StamPLC IoT Programmable Logic Controller, IoT Programmable Logic Controller, Programmable Logic Controller, Logic Controller

Ntụaka

Akwụkwọ ntuziaka onye ọrụ

M5STACK StamPLC IoT Njikwa Logic Programmable

Nkọwapụta