ይዘቶች መደበቅ
1 M5STACK ሴንትamPየ LC IoT ፕሮግራም ሎጂክ መቆጣጠሪያ
2 ዝርዝሮች
3 የምርት አጠቃቀም መመሪያዎች
4 የውጭ መስመር
5 Stam PLC
6 የሞዱል መጠን
7 በፍጥነት ጀምር
8 የ WiFi መረጃን አትም
9 የFCC ማስጠንቀቂያ
10 FCC የጨረር መጋለጥ መግለጫ
11 Arduino ጫን
12 በተደጋጋሚ የሚጠየቁ ጥያቄዎች
13 ሰነዶች / መርጃዎች
13.1 ዋቢዎች

M5STACK-LOGO

M5STACK ሴንትamPየ LC IoT ፕሮግራም ሎጂክ መቆጣጠሪያ

M5STACK-StamPLC-IoT-Programmable-Logic-Controller-PRODUCT

ዝርዝሮች

ዝርዝር መግለጫ መለኪያ
የመቆጣጠሪያ ሞዱል StampS3A contro1 module,based on ESP32-S3FN8,includes 8MB Flash,2.4GHz Wi-Fi,Bluetooth Low Energy (BLE)
ፍላሽ 8 ሜባ
ዲጂታል ግብዓቶች 8 channels of opto-isolated digital inputs, input voltage range: DC 5~36V
Digital 0utputs 4-channel relay outputs
ቅብብሎሽ AC 5A@250V,DC 5A@28V
የዲሲ የኃይል አቅርቦት supports DC 6~36V@1A wide voltage supply,DC power cornnector:DC5521 female,5.5x 2.1mm(center-positive)Expansion
n Interfaces GPIO.EXT interface,2 Grove interfaces
የመገናኛ በይነገጾች Onboard PWR-CAN and PWR-485 interfaces
PWR-CAN Interface XT30(2+2)PW-M
PWR-485 Interface HT3.96-4P
ማሳያ 1.14-inch color display(135×240 resolution),driven by the ST7789v2 chip
Contro1 &Interaction 1 RESET/B00T button,3 user buttons, buzzer
የውሂብ ማከማቻ አብሮ የተሰራ የማይክሮ ኤስዲ ካርድ ማስገቢያ
ዳሳሾች LM75 temperature sensor,INA226 voltage/current sensor,RTC(RX8130CE)
I/0 Port Load Capacity 2×8 expansion interface:maximum 1oad capacity DC 4.76V @700mA,Grove port 1oad capacity:DC 4.81V e 700mA
የኃይል ፍጆታ Standby current:(5V supp1y)DC 5V@21.60mA,(12V supply)DC 12Ve15.22mA;Operating current:(5V supply)DC 5Ve93.89mA, (12V supply)DC 12V@47.84mA
የመጫኛ ዘዴ DIN የባቡር ሐዲድ መዘርጋት
የአሠራር ሙቀት -10 ~ 50 ° ሴ
የምርት ልኬቶች 72.0×80.0×31.7ሚሜ
የምርት ክብደት 139.4 ግ
የጥቅል ልኬቶች 102.0x 94.0 x 37ሚሜ
አጠቃላይ ክብደት 163.7 ግ
አምራች M5Stack ቴክኖሎጂ Co., Ltd

Block A10, Expo Bay South Coast, Fuhai Street, Bao’an District, Shenzhen, China
Frequency Range for CE 2.4G Wi-Fi: 2412-2472MHz/2422-2462MHz BLE: 2402-2480MHz
Maximum EIRP for CE BLE፡ 6.84dBm

2.4ጂ ዋይፋይ፡ 17.90ዲቢኤም

የምርት አጠቃቀም መመሪያዎች

ፈጣን ጅምር
To get started with your Stam PLC, follow these steps:

SCAN Wi-Fi

  1. Power on the Stam PLC using the provided DC power supply.
  2. Press the RESET/BOOT button to start the device.
  3. Access the Wi-Fi settings on your device and scan for available networks.
  4. Select the appropriate Wi-Fi network and enter the password if required.
  5. Once connected, you can start utilizing the wireless communication capabilities of the Stam PLC.

SCAN BLE

  1. Ensure the Stam PLC is powered on and operational.
  2. Activate the Bluetooth settings on your device.
  3. Scan for available Bluetooth devices in the vicinity.
  4. Select the Stam PLC from the list of discovered devices to establish a BLE connection.
  5. You can now leverage the BLE functionality for data transfer and control.

የውጭ መስመር

Stam PLC is an IoT programmable logic controller designed for industrial automation and remote monitoring. The product is based on the StampS3A control module, which not only delivers powerful processing capabilities but also provides efficient wireless connectivity. In terms of control, Stam PLC offers 8 opto-isolated digital inputs and 4 relay outputs (supporting both AC and DC loads), along with a
GPIO.EXT port and 2 Grove interfaces, making the integration of various sensors and actuators both simple and reliable. Meanwhile, through the onboard PWR-CAN and PWR-485 interfaces, the device can be seamlessly integrated into industrial fieldbus networks, enabling remote data transmission and centralized control.

For human-machine interaction, the product features a 1.14-inch color display, a RESET/BOOT button, 3 user buttons, and a buzzer, which facilitate real-time parameter configuration and status monitoring, and can alert users in the event of anomalies. To withstand harsh industrial environments, Stam PLC supports a wide voltage input (DC 6–36V) and is designed for DIN rail mounting to ensure secure installation; the built-in Micro SD card slot further facilitates data storage and firmware updates.

Additionally, its environmental monitoring system integrates an LM75 temperature sensor and an INA226 voltage/current sensor for real-time feedback on device operation, while the RTC (RX8130CE) module ensures accurate time synchronization and log recording. The factory firmware automatically uploads data to M5’s EZDATA cloud platform, generating monitoring pages and offering users convenient remote cloud access and control. This product is suitable for industrial automation, remote monitoring, smart manufacturing, and other applications.

Stam PLC

የግንኙነት ችሎታዎች

  • Main Controller: ESP32-S3FN8 (StampS3A control module)
  • Wireless Communication: Wi‑Fi (2.4 GHz) and Bluetooth Low Energy (BLE)
  • CAN Bus: Onboard PWR‑CAN interface for reliable industrial data communication, RS-485:
  • Onboard PWR‑485 interface supporting remote control via the Modbus RTU protocol

ፕሮሰሰር እና አፈጻጸም

  • Processor Model: Xtensa LX7 dual-core (ESP32-S3FN8)
  • የማከማቻ አቅም፡ 8ሜባ ፍላሽ
  • Operating Frequency: Up to 240 MHz on a dual‑core 32-bit LX7 microprocessor

ማሳያ እና ግቤት

  • Display: 1.14‑inch color TFT display for real‑time parameter monitoring
  • Buttons: 1 RESET/BOOT button plus 3 user buttons for control and configuration. Buzzer:
  • Built‑in buzzer for audio alerts and notifications
  • RGB LED: Integrated RGB LED for dynamic visual feedback

የ GPIO ፒን እና ፕሮግራም ሊደረጉ የሚችሉ በይነገጾች

  • GPIO Pins: Provides multiple configurable GPIO pins (detailed mapping available in documentation)
  • Expansion Interfaces:
    • 2 Grove interfaces for easy sensor and actuator connection
    • GPIO.EXT interface for additional connectivity
    • Micro SD card slot for data storage and firmware updates

ሌሎች

  • Onboard Interfaces: Type‑C connector for programming, power supply, and serial communication
  • Physical Dimensions: 72.0 × 80.0 × 31.7 mm with DIN rail mount design, suitable for harsh industrial environments
  • Power Input: Wide voltage input ranging from DC 6–36V
  • Integrated Sensors: Includes LM75 temperature sensor, INA226 voltage/current sensor, and RTC (RX8130CE) for accurate time synchronization and log recording
  • Relay Outputs: 4‑channel relay outputs supporting AC 5A @ 250V / DC 5A @ 28V Opto-Isolated Digital Inputs: 8 channels designed to support DC 5–36V inputs for safe signal acq

የሞዱል መጠን

M5STACK-StamPLC-IoT-Programmable-Logic-Controller-FIG- (1)

በፍጥነት ጀምር

Before you do this step, look at the text in the final appendix: Installing Arduino.

የ WiFi መረጃን አትም

  1. Arduino IDE ን ይክፈቱ (ይመልከቱ https://docs.m5stack.com/en/arduino/arduino_ide ለልማት ቦርድ እና ሶፍትዌር የመጫኛ መመሪያ)
  2. Select the ESP32S3 DEV Module board and the corresponding port, then upload the code.e
  3. የተቃኘውን ዋይፋይ እና የሲግናል ጥንካሬ መረጃ ለማሳየት ተከታታይ ማሳያውን ይክፈቱ።

M5STACK-StamPLC-IoT-Programmable-Logic-Controller-FIG- (2)M5STACK-StamPLC-IoT-Programmable-Logic-Controller-FIG- (3)

በፍጥነት ጀምር
Before you do this step, look at the text in the final appendix: Installing Arduin.

የ BLE መረጃ ያትሙ

  1. Arduino IDE ን ይክፈቱ (ይመልከቱ https://docs.m5stack.com/en/arduino/arduino_ide ለልማት ቦርድ እና ሶፍትዌር የመጫኛ መመሪያ)
  2. የESP32S3 DEV ሞጁል ሰሌዳውን እና ተጓዳኝ ወደብ ይምረጡ እና ኮዱን ይስቀሉ።
  3. የተቃኘውን BLE እና የሲግናል ጥንካሬ መረጃ ለማሳየት ተከታታይ ማሳያውን ይክፈቱ።

M5STACK-StamPLC-IoT-Programmable-Logic-Controller-FIG- (4)M5STACK-StamPLC-IoT-Programmable-Logic-Controller-FIG- (5)

የFCC ማስጠንቀቂያ

የኤፍሲሲ ጥንቃቄ፡-
ለማክበር ኃላፊነት ባለው አካል በግልፅ ያልፀደቁ ማንኛቸውም ለውጦች ወይም ማሻሻያዎች የተጠቃሚውን መሳሪያ የማንቀሳቀስ ስልጣን ሊያሳጡ ይችላሉ።
ይህ መሳሪያ የFCC ደንቦች ክፍል 15ን ያከብራል።

ክዋኔው በሚከተሉት ሁለት ሁኔታዎች ተገዢ ነው.

  1. ይህ መሳሪያ ጎጂ ጣልቃገብነትን ላያመጣ ይችላል እና
  2. ይህ መሳሪያ ያልተፈለገ ስራን የሚያስከትል ጣልቃገብነትን ጨምሮ የደረሰውን ማንኛውንም ጣልቃ ገብነት መቀበል አለበት።

ጠቃሚ ማስታወሻ፡-

ማስታወሻ፡- በFCC ሕጎች ክፍል 15 መሠረት ይህ መሣሪያ ለክፍል B ዲጂታል መሣሪያ ተሞክሮ እና ገደቡን የሚያከብር ሆኖ ተገኝቷል። እነዚህ ወሰኖች የተነደፉት በመኖሪያ ተከላ ውስጥ ካለው ጎጂ ጣልቃገብነት ምክንያታዊ ጥበቃን ለመስጠት ነው። ይህ መሳሪያ የሬድዮ ፍሪኩዌንሲ ሃይልን ያመነጫል፣ ይጠቀማል እና ሊያሰራጭ ይችላል፣ እና ካልተጫነ እና በመመሪያው መሰረት ጥቅም ላይ ካልዋለ በሬዲዮ ግንኙነቶች ላይ ጎጂ ጣልቃገብነት ያስከትላል። ነገር ግን, በአንድ የተወሰነ መጫኛ ውስጥ ጣልቃገብነት ላለመከሰቱ ምንም ዋስትና የለም.

ይህ መሳሪያ በሬዲዮ ወይም በቴሌቭዥን መቀበያ ላይ ጎጂ የሆነ ጣልቃገብነት የሚያስከትል ከሆነ መሳሪያውን በማጥፋት እና በማብራት ሊታወቅ የሚችል ከሆነ ተጠቃሚው ከሚከተሉት እርምጃዎች በአንዱ ወይም ከዚያ በላይ በሆነ መልኩ ጣልቃ ገብነትን ለማስተካከል እንዲሞክር ይበረታታል።

  • የመቀበያ አንቴናውን አቅጣጫ ቀይር ወይም ወደ ሌላ ቦታ ቀይር።
  • በመሳሪያው እና በተቀባዩ መካከል ያለውን ልዩነት ይጨምሩ.
  • መሳሪያውን ተቀባዩ ከተገናኘበት በተለየ ወረዳ ላይ ወደ መውጫው ያገናኙ.
  • ለእርዳታ ሻጩን ወይም ልምድ ያለው የሬዲዮ/ቲቪ ቴክኒሻን አማክር።

FCC የጨረር መጋለጥ መግለጫ

ይህ መሳሪያ ቁጥጥር ለሌለው አካባቢ የተቀመጡትን የ FCC የጨረር መጋለጥ ገደቦችን ያከብራል። ይህ መሳሪያ በራዲያተሩ እና በሰውነትዎ መካከል ቢያንስ 20 ሴ.ሜ ርቀት ላይ መጫን እና መስራት አለበት።

Arduino ጫን

Arduino IDE በመጫን ላይhttps://www.arduino.cc/en/Main/Software)

የ Arduino ባለስልጣንን ለመጎብኘት ጠቅ ያድርጉ webጣቢያ, እና የእርስዎን ስርዓተ ክወና ለማውረድ የመጫኛ ፓኬጁን ይምረጡ.

Arduino ቦርድ አስተዳደር በመጫን ላይ

  1. የቦርድ ሥራ አስኪያጅ URL ለአንድ የተወሰነ መድረክ የእድገት ቦርድ መረጃን ለመጠቆም ጥቅም ላይ ይውላል. በ Arduino IDE ምናሌ ውስጥ ይምረጡ File -> ምርጫዎችM5STACK-StamPLC-IoT-Programmable-Logic-Controller-FIG- (6)
  2. የESP ቦርድ አስተዳደርን ይቅዱ URL ከታች ወደ ተጨማሪ የቦርድ ሥራ አስኪያጅ URLs field, and save. https://espressif.github.io/arduino-esp32/package_esp32_dev_index.jsonM5STACK-StamPLC-IoT-Programmable-Logic-Controller-FIG- (7)
  3. በጎን አሞሌው ውስጥ የቦርድ አስተዳዳሪን ይምረጡ ፣ ኢኤስፒን ይፈልጉ እና ጫንን ጠቅ ያድርጉ።M5STACK-StamPLC-IoT-Programmable-Logic-Controller-FIG- (8)
  4. በጎን አሞሌው ውስጥ የቦርድ አስተዳዳሪን ይምረጡ፣ M5Stackን ይፈልጉ እና ጫንን ጠቅ ያድርጉ።
    ጥቅም ላይ በሚውለው ምርት ላይ በመመስረት በመሳሪያዎች -> ቦርድ -> M5Stack -> {ESP32S3 DEV Moduleboard} ስር ያለውን ተዛማጅ የልማት ሰሌዳ ይምረጡ።M5STACK-StamPLC-IoT-Programmable-Logic-Controller-FIG- (9)
  5. ፕሮግራሙን ለመስቀል መሳሪያውን ከኮምፒዩተርዎ ጋር በመረጃ ገመድ ያገናኙት።

በተደጋጋሚ የሚጠየቁ ጥያቄዎች

የሚመከር የክወና ጥራዝ ምንድን ነውtage for the Stam PLC?

የሚመከረው የክወና ጥራዝtage is between DC 6V to 36V with a current supply of 1A. Ensure to use a compatible DC power supply for optimal performance.

How can I expand the functionality of the Stam PLC?

You can expand the functionality by utilizing the GPIO pins and additional interfaces provided. Connect sensors and actuators to the Grove interfaces for enhanced capabilities.

ሰነዶች / መርጃዎች

M5STACK ሴንትamPየ LC IoT ፕሮግራም ሎጂክ መቆጣጠሪያ [pdf] የተጠቃሚ መመሪያ
StamPLC IoT Programmable Logic Controller, IoT Programmable Logic Controller, Programmable Logic Controller, Logic Controller

ዋቢዎች

አስተያየት ይስጡ

የኢሜል አድራሻዎ አይታተምም። አስፈላጊ መስኮች ምልክት ተደርጎባቸዋል *