M5STACK StamPKidhibiti cha Mantiki cha LC IoT

Vipimo

Vipimo	Kigezo
Moduli ya Kudhibiti	StampS3A contro1 moduli, kulingana na ESP32-S3FN8, inajumuisha 8MB Flash, 2.4GHz Wi-Fi, Bluetooth Low Energy (BLE)
MWELEKEZO	8MB
Pembejeo za Dijitali	8 channels of opto-isolated digital inputs, input voltage mbalimbali: DC 5~36V
Matokeo 0 ya dijiti	Matokeo ya relay ya njia 4
Reli	AC 5A@250V,DC 5A@28V
Ugavi wa Nguvu wa DC	supports DC 6~36V@1A wide voltage supply,DC power cornnector:DC5521 female,5.5x 2.1mm(center-positive)Expansion
n Interfaces	GPIO.EXT interface,2 Grove interfaces
Violesura vya Mawasiliano	Miingiliano ya Onboard PWR-CAN na PWR-485
PWR-CAN Interface	XT30(2+2)PW-M
PWR-485 Interface	HT3.96-4P
Onyesho	Onyesho la rangi ya inchi 1.14 (azimio la 135×240), inayoendeshwa na chipu ST7789v2
Contro1 &Interaction	1 RESET/B00T button,3 user buttons, buzzer
Hifadhi ya Data	Nafasi ya kadi ya SD iliyojengwa ndani
Sensorer	Sensor ya joto ya LM75,INA226 voltagKihisi cha e/sasa,RTC(RX8130CE)
I/0 Uwezo wa Kupakia Bandari	2x8 kiolesura cha upanuzi: upeo wa uwezo wa 1oad DC 4.76V @700mA,Grove port 1oad capacity:DC 4.81V e 700mA
Matumizi ya Nguvu	Standby current:(5V supp1y)DC 5V@21.60mA,(12V supply)DC 12Ve15.22mA;Operating current:(5V supply)DC 5Ve93.89mA, (12V supply)DC 12V@47.84mA
Njia ya Ufungaji	Ufungaji wa reli ya DIN
Joto la Uendeshaji	-10 ~ 50°C
Vipimo vya Bidhaa	72.0×80.0×31.7mm
Uzito wa Bidhaa	139.4g
Vipimo vya Kifurushi	102.0x 94.0 x 37mm
Uzito wa Jumla	163.7g
Mtengenezaji	M5Stack Technology Co., Ltd Block A10, Expo Bay South Coast, Fuhai Street, Bao'an District, Shenzhen, China
Masafa ya Marudio kwa CE	2.4G Wi-Fi: 2412-2472MHz/2422-2462MHz BLE: 2402-2480MHz
Upeo wa EIRP kwa CE	BLE: 6.84dBm 2.4G Wi-Fi: 17.90dBm

Maagizo ya Matumizi ya Bidhaa

Anza Haraka
Ili kuanza na Stam PLC yako, fuata hatua hizi:

TANGAZA Wi-Fi

1. Nishati kwenye Stam PLC kwa kutumia usambazaji wa umeme wa DC uliotolewa.
2. Bonyeza kitufe cha RESET/BOOT ili kuanza kifaa.
3. Access the Wi-Fi settings on your device and scan for available networks.
4. Select the appropriate Wi-Fi network and enter the password if required.
5. Once connected, you can start utilizing the wireless communication capabilities of the Stam PLC.

CHANGANUA BLE

1. Hakikisha kuwa Stam PLC imewashwa na inafanya kazi.
2. Washa mipangilio ya Bluetooth kwenye kifaa chako.
3. Changanua vifaa vya Bluetooth vinavyopatikana karibu nawe.
4. Select the Stam PLC from the list of discovered devices to establish a BLE connection.
5. You can now leverage the BLE functionality for data transfer and control.

MUHTASARI

Stam PLC ni kidhibiti cha mantiki kinachoweza kupangwa cha IoT iliyoundwa kwa ajili ya mitambo ya viwandani na ufuatiliaji wa mbali. Bidhaa hiyo inategemea StampS3A control module, which not only delivers powerful processing capabilities but also provides efficient wireless connectivity. In terms of control, Stam PLC offers 8 opto-isolated digital inputs and 4 relay outputs (supporting both AC and DC loads), along with a
GPIO.EXT port and 2 Grove interfaces, making the integration of various sensors and actuators both simple and reliable. Meanwhile, through the onboard PWR-CAN and PWR-485 interfaces, the device can be seamlessly integrated into industrial fieldbus networks, enabling remote data transmission and centralized control.

For human-machine interaction, the product features a 1.14-inch color display, a RESET/BOOT button, 3 user buttons, and a buzzer, which facilitate real-time parameter configuration and status monitoring, and can alert users in the event of anomalies. To withstand harsh industrial environments, Stam PLC supports a wide voltage input (DC 6–36V) and is designed for DIN rail mounting to ensure secure installation; the built-in Micro SD card slot further facilitates data storage and firmware updates.

Additionally, its environmental monitoring system integrates an LM75 temperature sensor and an INA226 voltage/sensor ya sasa kwa maoni ya wakati halisi juu ya uendeshaji wa kifaa, wakati moduli ya RTC (RX8130CE) inahakikisha usawazishaji sahihi wa wakati na kurekodi kumbukumbu. Firmware ya kiwanda hupakia data kiotomatiki kwenye jukwaa la wingu la EZDATA la M5, na kutengeneza kurasa za ufuatiliaji na kuwapa watumiaji ufikiaji na udhibiti wa mbali wa mbali. Bidhaa hii inafaa kwa mitambo ya kiotomatiki ya viwandani, ufuatiliaji wa mbali, utengenezaji mahiri, na programu zingine.

Stam PLC

Uwezo wa Mawasiliano

• Main Controller: ESP32-S3FN8 (StampS3A control module)
• Wireless Communication: Wi‑Fi (2.4 GHz) and Bluetooth Low Energy (BLE)
• CAN Bus: Onboard PWR‑CAN interface for reliable industrial data communication, RS-485:
• Onboard PWR‑485 interface supporting remote control via the Modbus RTU protocol

Kichakataji na Utendaji

• Processor Model: Xtensa LX7 dual-core (ESP32-S3FN8)
• Uwezo wa Kuhifadhi: 8MB Flash
• Operating Frequency: Up to 240 MHz on a dual‑core 32-bit LX7 microprocessor

Onyesho na Ingizo

• Display: 1.14‑inch color TFT display for real‑time parameter monitoring
• Buttons: 1 RESET/BOOT button plus 3 user buttons for control and configuration. Buzzer:
• Built‑in buzzer for audio alerts and notifications
• RGB LED: Integrated RGB LED for dynamic visual feedback

Pini za GPIO na violesura vinavyoweza kupangwa

• GPIO Pins: Provides multiple configurable GPIO pins (detailed mapping available in documentation)
• Violesura vya Upanuzi:
  • 2 Grove interfaces for easy sensor and actuator connection
  • GPIO.EXT interface for additional connectivity
  • Micro SD card slot for data storage and firmware updates

Wengine

• Onboard Interfaces: Type‑C connector for programming, power supply, and serial communication
• Physical Dimensions: 72.0 × 80.0 × 31.7 mm with DIN rail mount design, suitable for harsh industrial environments
• Power Input: Wide voltage input ranging from DC 6–36V
• Integrated Sensors: Includes LM75 temperature sensor, INA226 voltage/current sensor, and RTC (RX8130CE) for accurate time synchronization and log recording
• Relay Outputs: 4‑channel relay outputs supporting AC 5A @ 250V / DC 5A @ 28V Opto-Isolated Digital Inputs: 8 channels designed to support DC 5–36V inputs for safe signal acq

Ukubwa wa Moduli

ANZA HARAKA

Before you do this step, look at the text in the final appendix: Installing Arduino.

Chapisha maelezo ya WiFi

1. Fungua IDE ya Arduino (Rejelea https://docs.m5stack.com/en/arduino/arduino_ide kwa mwongozo wa usakinishaji wa bodi ya ukuzaji na programu)
2. Select the ESP32S3 DEV Module board and the corresponding port, then upload the code.e
3. Fungua kifuatiliaji mfululizo ili kuonyesha WiFi iliyochanganuliwa na maelezo ya nguvu ya mawimbi.

ANZA HARAKA
Before you do this step, look at the text in the final appendix: Installing Arduin.

Chapisha habari ya BLE

1. Fungua IDE ya Arduino (Rejelea https://docs.m5stack.com/en/arduino/arduino_ide kwa mwongozo wa usakinishaji wa bodi ya ukuzaji na programu)
2. Chagua ubao wa Moduli ya ESP32S3 DEV na bandari inayolingana, kisha upakie msimbo.
3. Fungua ufuatiliaji wa ufuatiliaji ili kuonyesha BLE iliyochanganuliwa na maelezo ya nguvu ya ishara.

Onyo la FCC

Tahadhari ya FCC:
Mabadiliko yoyote au marekebisho ambayo hayajaidhinishwa waziwazi na mhusika anayehusika na utiifu yanaweza kubatilisha mamlaka ya mtumiaji kuendesha kifaa.
Kifaa hiki kinatii sehemu ya 15 ya Sheria za FCC.

Operesheni inategemea masharti mawili yafuatayo:

1. Kifaa hiki hakiwezi kusababisha usumbufu unaodhuru, na
2. Kifaa hiki lazima kikubali uingiliaji wowote uliopokewa, ikiwa ni pamoja na uingiliaji ambao unaweza kusababisha uendeshaji usiohitajika.

KUMBUKA MUHIMU:

Kumbuka: Kifaa hiki kimejaribiwa na kupatikana kuwa kinatii vikomo vya kifaa cha kidijitali cha Hatari B, kwa mujibu wa sehemu ya 15 ya Sheria za FCC. Vikomo hivi vimeundwa ili kutoa ulinzi unaofaa dhidi ya kuingiliwa kwa hatari katika usakinishaji wa makazi. Kifaa hiki huzalisha, kutumia, na kuangazia nishati ya masafa ya redio na, ikiwa hakijasakinishwa na kutumiwa kwa mujibu wa maagizo, kinaweza kusababisha mwingiliano unaodhuru kwa mawasiliano ya redio. Hata hivyo, hakuna uhakika kwamba kuingiliwa haitatokea katika ufungaji fulani.

Ikiwa kifaa hiki kitasababisha usumbufu unaodhuru kwa upokeaji wa redio au televisheni, ambao unaweza kubainishwa kwa kuzima na kuwasha kifaa, mtumiaji anahimizwa kujaribu kusahihisha uingiliaji huo kwa moja au zaidi ya hatua zifuatazo:

• Elekeza upya au uhamishe tena antena inayopokea.
• Kuongeza utengano kati ya kifaa na mpokeaji.
• Unganisha vifaa kwenye plagi kwenye mzunguko tofauti na ile ambayo mpokeaji ameunganishwa.
• Wasiliana na muuzaji au mtaalamu wa redio/TV kwa usaidizi.

Taarifa ya Mfiduo wa Mionzi ya FCC

Kifaa hiki kinatii vikomo vya mfiduo wa mionzi ya FCC vilivyowekwa kwa mazingira yasiyodhibitiwa. Kifaa hiki kinapaswa kusanikishwa na kuendeshwa kwa umbali wa angalau 20cm kati ya radiator na mwili wako.

Ufungaji wa Arduino

Kufunga Arduino IDE (https://www.arduino.cc/en/Main/Software)

Bofya ili kutembelea afisa wa Arduino webtovuti, na uchague kifurushi cha usakinishaji kwa mfumo wako wa uendeshaji kupakua.

Kufunga Usimamizi wa Bodi ya Arduino

1. Meneja wa Bodi URL hutumika kuorodhesha maelezo ya bodi ya ukuzaji kwa jukwaa mahususi. Katika orodha ya Arduino IDE, chagua File -> Mapendeleo
2. Nakili usimamizi wa bodi ya ESP URL chini ndani ya Meneja wa Bodi ya Ziada URLs field, and save. https://espressif.github.io/arduino-esp32/package_esp32_dev_index.json
3. Katika upau wa kando, chagua Meneja wa Bodi, tafuta ESP, na ubofye Sakinisha.
4. Katika upau wa kando, chagua Meneja wa Bodi, tafuta M5Stack, na ubofye Sakinisha.
   Kulingana na bidhaa iliyotumiwa, chagua ubao wa ukuzaji unaolingana chini ya Zana -> Ubao -> M5Stack -> {Ubao wa Moduli ya ESP32S3 DEV}.
5. Unganisha kifaa kwenye kompyuta yako na kebo ya data ili kupakia programu.

Maswali Yanayoulizwa Mara Kwa Mara

Ni kiasi gani cha uendeshaji kinachopendekezwatage kwa Stam PLC?

Kiwango cha uendeshaji kilichopendekezwatage is between DC 6V to 36V with a current supply of 1A. Ensure to use a compatible DC power supply for optimal performance.

How can I expand the functionality of the Stam PLC?

You can expand the functionality by utilizing the GPIO pins and additional interfaces provided. Connect sensors and actuators to the Grove interfaces for enhanced capabilities.

Nyaraka / Rasilimali

M5STACK StamPKidhibiti cha Mantiki cha LC IoT [pdf] Mwongozo wa Mtumiaji StamPLC IoT Kidhibiti cha Mantiki Kinachoweza Kupangwa, Kidhibiti cha Mantiki Kinachoweza Kupangwa cha IoT, Kidhibiti cha Mantiki Kinachoweza Kuratibiwa, Kidhibiti Mantiki.

Marejeleo

• Mwongozo wa Mtumiaji