Ulica M5STACKamPLC IoT programabilni logični krmilnik
Specifikacije
| Specifikacija | Parameter |
| Nadzorni modul | StampS3A contro1 module,based on ESP32-S3FN8,includes 8MB Flash,2.4GHz Wi-Fi,Bluetooth Low Energy (BLE) |
| FLASH | 8 MB |
| Digitalni vhodi | 8 channels of opto-isolated digital inputs, input voltage range: DC 5~36V |
| Digital 0utputs | 4-channel relay outputs |
| Releji | AC 5A@250V,DC 5A@28V |
| Enosmerno napajanje | supports DC 6~36V@1A wide voltage supply,DC power cornnector:DC5521 female,5.5x 2.1mm(center-positive)Expansion |
| n Interfaces | GPIO.EXT interface,2 Grove interfaces |
| Komunikacijski vmesniki | Onboard PWR-CAN and PWR-485 interfaces |
| PWR-CAN Interface | XT30(2+2)PW-M |
| PWR-485 Interface | HT3.96-4P |
| Zaslon | 1.14-inch color display(135×240 resolution),driven by the ST7789v2 chip |
| Contro1 &Interaction | 1 RESET/B00T button,3 user buttons, buzzer |
| Shranjevanje podatkov | Vgrajena reža za kartico Micro SD |
| Senzorji | LM75 temperature sensor,INA226 voltage/current sensor,RTC(RX8130CE) |
| I/0 Port Load Capacity | 2×8 expansion interface:maximum 1oad capacity DC 4.76V @700mA,Grove port 1oad capacity:DC 4.81V e 700mA |
| Poraba energije | Standby current:(5V supp1y)DC 5V@21.60mA,(12V supply)DC 12Ve15.22mA;Operating current:(5V supply)DC 5Ve93.89mA, (12V supply)DC 12V@47.84mA |
| Način namestitve | Montaža na DIN letev |
| Delovna temperatura | -10~50°C |
| Dimenzije izdelka | 72.0×80.0×31.7 mm |
| Teža izdelka | 139.4 g |
| Dimenzije paketa | 102.0 x 94.0 x 37 mm |
| Bruto teža | 163.7 g |
| Proizvajalec | M5Stack Technology Co., Ltd
Block A10, Expo Bay South Coast, Fuhai Street, Bao’an District, Shenzhen, China |
| Frequency Range for CE | 2.4G Wi-Fi: 2412-2472MHz/2422-2462MHz BLE: 2402-2480MHz |
| Največja EIRP za CE | BLE: 6.84 dBm
2.4 G Wi-Fi: 17.90 dBm |
Navodila za uporabo izdelka
Hitri začetek
To get started with your Stam PLC, follow these steps:
SCAN Wi-Fi
- Power on the Stam PLC using the provided DC power supply.
- Press the RESET/BOOT button to start the device.
- Access the Wi-Fi settings on your device and scan for available networks.
- Select the appropriate Wi-Fi network and enter the password if required.
- Once connected, you can start utilizing the wireless communication capabilities of the Stam PLC.
SCAN BLE
- Ensure the Stam PLC is powered on and operational.
- Activate the Bluetooth settings on your device.
- Scan for available Bluetooth devices in the vicinity.
- Select the Stam PLC from the list of discovered devices to establish a BLE connection.
- You can now leverage the BLE functionality for data transfer and control.
ORIS
Stam PLC is an IoT programmable logic controller designed for industrial automation and remote monitoring. The product is based on the StampS3A control module, which not only delivers powerful processing capabilities but also provides efficient wireless connectivity. In terms of control, Stam PLC offers 8 opto-isolated digital inputs and 4 relay outputs (supporting both AC and DC loads), along with a
GPIO.EXT port and 2 Grove interfaces, making the integration of various sensors and actuators both simple and reliable. Meanwhile, through the onboard PWR-CAN and PWR-485 interfaces, the device can be seamlessly integrated into industrial fieldbus networks, enabling remote data transmission and centralized control.
For human-machine interaction, the product features a 1.14-inch color display, a RESET/BOOT button, 3 user buttons, and a buzzer, which facilitate real-time parameter configuration and status monitoring, and can alert users in the event of anomalies. To withstand harsh industrial environments, Stam PLC supports a wide voltage input (DC 6–36V) and is designed for DIN rail mounting to ensure secure installation; the built-in Micro SD card slot further facilitates data storage and firmware updates.
Additionally, its environmental monitoring system integrates an LM75 temperature sensor and an INA226 voltage/current sensor for real-time feedback on device operation, while the RTC (RX8130CE) module ensures accurate time synchronization and log recording. The factory firmware automatically uploads data to M5’s EZDATA cloud platform, generating monitoring pages and offering users convenient remote cloud access and control. This product is suitable for industrial automation, remote monitoring, smart manufacturing, and other applications.
Stam PLC
Komunikacijske zmogljivosti
- Main Controller: ESP32-S3FN8 (StampS3A control module)
- Wireless Communication: Wi‑Fi (2.4 GHz) and Bluetooth Low Energy (BLE)
- CAN Bus: Onboard PWR‑CAN interface for reliable industrial data communication, RS-485:
- Onboard PWR‑485 interface supporting remote control via the Modbus RTU protocol
Procesor in zmogljivost
- Processor Model: Xtensa LX7 dual-core (ESP32-S3FN8)
- Zmogljivost shranjevanja: 8 MB Flash
- Operating Frequency: Up to 240 MHz on a dual‑core 32-bit LX7 microprocessor
Zaslon in vnos
- Display: 1.14‑inch color TFT display for real‑time parameter monitoring
- Buttons: 1 RESET/BOOT button plus 3 user buttons for control and configuration. Buzzer:
- Built‑in buzzer for audio alerts and notifications
- RGB LED: Integrated RGB LED for dynamic visual feedback
GPIO zatiči in programabilni vmesniki
- GPIO Pins: Provides multiple configurable GPIO pins (detailed mapping available in documentation)
- Expansion Interfaces:
- 2 Grove interfaces for easy sensor and actuator connection
- GPIO.EXT interface for additional connectivity
- Micro SD card slot for data storage and firmware updates
drugi
- Onboard Interfaces: Type‑C connector for programming, power supply, and serial communication
- Physical Dimensions: 72.0 × 80.0 × 31.7 mm with DIN rail mount design, suitable for harsh industrial environments
- Power Input: Wide voltage input ranging from DC 6–36V
- Integrated Sensors: Includes LM75 temperature sensor, INA226 voltage/current sensor, and RTC (RX8130CE) for accurate time synchronization and log recording
- Relay Outputs: 4‑channel relay outputs supporting AC 5A @ 250V / DC 5A @ 28V Opto-Isolated Digital Inputs: 8 channels designed to support DC 5–36V inputs for safe signal acq
Velikost modula
HITRI ZAČETEK
Before you do this step, look at the text in the final appendix: Installing Arduino.
Natisnite podatke WiFi
- Odprite Arduino IDE (Glejte https://docs.m5stack.com/en/arduino/arduino_ide za navodila za namestitev razvojne plošče in programske opreme)
- Select the ESP32S3 DEV Module board and the corresponding port, then upload the code.e
- Odprite serijski monitor, da prikažete skenirane informacije o WiFi in moči signala.
HITRI ZAČETEK
Before you do this step, look at the text in the final appendix: Installing Arduin.
Natisnite informacije BLE
- Odprite Arduino IDE (Glejte https://docs.m5stack.com/en/arduino/arduino_ide za navodila za namestitev razvojne plošče in programske opreme)
- Izberite ploščo modula ESP32S3 DEV in ustrezna vrata, nato naložite kodo.
- Odprite serijski monitor, da prikažete optično prebrane BLE in informacije o moči signala.
Opozorilo FCC
Opozorilo FCC:
Vse spremembe ali modifikacije, ki jih ni izrecno odobrila stranka, odgovorna za skladnost, lahko razveljavijo uporabnikovo pooblastilo za uporabo opreme.
Ta naprava je skladna s 15. delom pravil FCC.
Delovanje je odvisno od naslednjih dveh pogojev:
- Ta naprava morda ne povzroča škodljivih motenj in
- Ta naprava mora sprejeti vse prejete motnje, vključno z motnjami, ki lahko povzročijo neželeno delovanje.
POMEMBNA OPOMBA:
Opomba: Ta oprema je bila testirana in ugotovljeno je bilo, da je v skladu z omejitvami za digitalne naprave razreda B v skladu s 15. delom pravil FCC. Te omejitve so zasnovane tako, da zagotavljajo primerno zaščito pred škodljivimi motnjami v stanovanjski namestitvi. Ta oprema ustvarja, uporablja in lahko oddaja radiofrekvenčno energijo in lahko povzroči škodljive motnje radijskih komunikacij, če ni nameščena in uporabljena v skladu z navodili. Vendar ni nobenega zagotovila, da do motenj ne bo prišlo pri določeni namestitvi.
Če ta oprema povzroča škodljive motnje pri radijskem ali televizijskem sprejemu, kar je mogoče ugotoviti z izklopom in vklopom opreme, uporabnika spodbujamo, da poskusi odpraviti motnje z enim ali več od naslednjih ukrepov:
- Preusmerite ali premaknite sprejemno anteno.
- Povečajte razdaljo med opremo in sprejemnikom.
- Priključite opremo v vtičnico na drugem tokokrogu kot tisti, na katerega je priključen sprejemnik.
- Za pomoč se posvetujte s prodajalcem ali izkušenim radijskim/TV tehnikom.
Izjava FCC o izpostavljenosti sevanju
Ta oprema je v skladu z omejitvami FCC za izpostavljenost sevanju, ki so določene za nenadzorovano okolje. To opremo je treba namestiti in uporabljati z najmanjšo razdaljo 20 cm med radiatorjem in vašim telesom.
Namestitev Arduino
Namestitev Arduino IDE (https://www.arduino.cc/en/Main/Software)
Kliknite za obisk uradnika Arduino webin izberite namestitveni paket za vaš operacijski sistem, ki ga želite prenesti.
Namestitev Arduino Board Management
- Vodja odbora URL se uporablja za indeksiranje informacij o razvojni plošči za določeno platformo. V meniju Arduino IDE izberite File -> Nastavitve
- Kopirajte upravljanje plošče ESP URL spodaj v dodatnega upravitelja odbora URLs field, and save. https://espressif.github.io/arduino-esp32/package_esp32_dev_index.json
- V stranski vrstici izberite Board Manager, poiščite ESP in kliknite Install.
- V stranski vrstici izberite Board Manager, poiščite M5Stack in kliknite Install.
Odvisno od uporabljenega izdelka izberite ustrezno razvojno ploščo pod Orodja -> Plošča -> M5Stack -> {ESP32S3 DEV Module board}.
- Povežite napravo z računalnikom s podatkovnim kablom, da naložite program.
Pogosto zastavljena vprašanja
Kakšna je priporočena delovna voltage for the Stam PLC?
Priporočena delovna voltage is between DC 6V to 36V with a current supply of 1A. Ensure to use a compatible DC power supply for optimal performance.
How can I expand the functionality of the Stam PLC?
You can expand the functionality by utilizing the GPIO pins and additional interfaces provided. Connect sensors and actuators to the Grove interfaces for enhanced capabilities.
Dokumenti / Viri
 |
Ulica M5STACKamPLC IoT programabilni logični krmilnik [pdf] Uporabniški priročnik StamPLC IoT Programmable Logic Controller, IoT Programmable Logic Controller, Programmable Logic Controller, Logic Controller |