ToolkitRC MC8 iBattery Checker ene-LCD Isibonisi soMsebenzisi weManuwali

Intshayelelo

Enkosi ngokuthenga i-MC8 yokujonga izinto ezininzi. Nceda ufunde le ncwadana ngononophelo phambi kokuba usebenzise isixhobo.

Iimpawu zezandla

• Ingcebiso
• Kubalulekile
• Uluhlu lwamagama

Iinkcukacha ezongezelelweyo

Ngolwazi oluthe vetshe malunga nokusebenza kunye nokugcinwa kwesixhobo sakho, nceda undwendwele eli khonkco lilandelayo: www.toolkitrc.com/mc8

Amanyathelo okhuseleko

1. Umthamo wokusebenzatagI-e ye-MC8 iphakathi kwe-DC 7.0V kunye ne-35.0V. Qinisekisa ukuba i-polarity yomthombo wamandla ayibuyiselwa umva phambi kokusetyenziswa.
2. Musa ukusebenza phantsi kobushushu obugqithisileyo, ukufuma, iindawo ezinokutsha neziqhumayo.
3. Ungaze uhambe ungajongwanga xa usebenza.
4. Nqamula umthombo wamandla xa ungasetyenziswa

Imveliso iphelileview

I-MC8 sisitsheki esihlangeneyo esilungiselelwe wonke umntu othanda izinto zokuzonwabisa. Inomboniso oqaqambileyo, onemibala ye-IPS, ichanekile ukuya kwi-5mV

• Imilinganiselo kunye nemilinganiselo ye-LiPo, i-LiHV, i-LiFe kunye neebhetri zeNgonyama.
• Umthamo obanzitage igalelo DC 7.0-35.0V.
• Ixhasa i-Main/Balance/I-Signal port power inputs.
• Imilinganiselo kunye neziphumo PWM, PPM, SBUS iimpawu.
• I-USB-A, i-USB-C i-double-port output.
• I-USB-C 20W PD imveliso yentlawulo ekhawulezayo.
• Ukhuseleko lokukhupha ibhetri. Ikhubaza ngokuzenzekelayo imveliso ye-USB xa ibhetri ifikelela kumanqanaba abalulekileyo.
• Umlinganiselo kunye nokuchaneka kwebhalansi: <0.005V.
• Ibhalansi yangoku: 60mA.
• 2.0 intshi, IPS igcwele viewumboniso we-angle.
• Isisombululo esiphezulu 320 * 240 pixels.

Uyilo

Ngaphambili

Ngasemva

Ukusetyenziswa kokuqala

1. Qhagamshela ibhetri kwizibuko lebhalansi yeMC8, okanye uqhagamshele i-7.0-35.0V voltage kwizibuko legalelo le-XT60 le-MC8.
2. Isikrini sibonisa uphawu lwe-boot kwimizuzwana eyi-0.5
3. Emva kokuba i-boot igqityiwe, isikrini singena kujongano oluphambili kwaye sibonisa ngolu hlobo lulandelayo:
   
4. Jika irola ukuze uskrole phakathi kweemenyu kunye nokhetho.
5. Cinezela ixesha elifutshane okanye elide kwirola ukufaka into
6. Sebenzisa isilayida esiphumayo ukulungisa imveliso yetshaneli.

Iskrola sisebenza ngokwahlukileyo kwizinto ezahlukeneyo zemenyu, nceda ujonge le miyalelo ilandelayo.

UmqulutagUvavanyo

Umqulutage ukubonisa kunye nokulinganisela (iiseli zomntu ngamnye)

Qhagamshela izibuko lebhetri kwiMC8. Emva kokuba isixhobo sisebenza, iphepha eliphambili libonisa umthamotagi-e yeseli nganye nganye- njengoko kubonisiwe ngezantsi:

Imivalo enemibala ibonisa umthamotage yebhetri ngokomzobo. Iseli enevolumu ephezulutagu-e uboniswa ngobomvu, ngelixa iseli enomthamo ophantsitage iboniswe ngombala oblowu. Umthamo opheleleyotage kunye nomqulutage umahluko (uphezulu voltagi-e-low voltage) iboniswe ngezantsi.

Kwimenyu engundoqo, cofa i [ivili] ukuqalisa umsebenzi webhalansi. I-MC8 isebenzisa izixhasi zangaphakathi ukukhupha i(izi)seli de ipakethe ifikelele kwivolthi efanayotage phakathi kweeseli (<0.005V umahluko)

1. Imivalo ilinganiswe kwii-LiPOs, ayichanekanga kwiibhetri nezinye iikhemistri.
2. Emva kokulinganisa ipakethi yebhetri, susa ibhetri kwi-MC8 ukunqanda ukukhupha kakhulu

Ipakethi yebhetri iyonke voltage

Qhagamshela intambo yebhetri kwizibuko eliphambili le-XT60 kwi-MC8 ukubonisa ivolthi epheleleyotage yebhetri pack, njengoko kubonisiwe ngezantsi.

1. I-MC8 ibonisa umthamo opheleleyotage yazo zonke iikhemistri zebhetri ezisebenza ngaphakathi kwemida yokufaka .

Umlinganiselo womqondiso 

PWM Umlinganiselo wophawu

Emva kokuba isixhobo sivuliwe, skrolela ngasekunene kube kanye kwirola yentsimbi ukuze ufake imo yokulinganisa. Iphepha liboniswa ngolu hlobo lulandelayo.

Inkcazo ye-UI
I-PWM: Uhlobo lomqondiso
1500: Okwangoku Ububanzi bokubetha kwe-PWM
20ms/5Hz : Umjikelo wangoku kunye nokuphindaphinda komqondiso wePWM

1. Xa usebenzisa umsebenzi wokulinganisa umqondiso. Izibuko lomqondiso, izibuko lebhalansi, kunye nezibuko legalelo elingundoqo zonke zinokubonelela ngamandla kwi-MC8

Umlinganiselo wesignali yePPM

Phantsi kwemowudi yomlinganiselo wesignali ye-PWM, cofa ezantsi kwisiskroli kwaye uskrole ngasekunene de kuboniswe iPPM. Emva koko umqondiso wePPM unokulinganiswa, njengoko kuboniswe ngezantsi.

SBUS Umlinganiselo wophawu

Phantsi kwemowudi yomlinganiselo wesignali ye-PWM, cofa ezantsi kwisiskroli kwaye uskrole ngasekunene de kuboniswe i-SBUS. Emva koko umqondiso we-SBUS unokulinganiswa, njengoko kuboniswe ngezantsi.

Isiphumo somqondiso

Imveliso yePWM Signal

Nge-MC8 elayitiweyo, skrola ngasekunene kabini kwirola ukufaka imo yokuPhuma. Cinezela ezantsi kwisikroli imizuzwana emi-2 ukufaka imowudi yokuphuma komqondiso, njengoko kubonisiwe ngezantsi. Inkcazo ye-UI

Imowudi: Imowudi yemveliso yomqondiso-inokutshintshwa phakathi kweendlela ze-manual kunye ne-3 ezizenzekelayo zezantya ezahlukeneyo.

Ububanzi : I-PWM yesiphumo sophawu lwe-pulse ububanzi, umda woluhlu 1000us-2000us. Xa isetelwe kwimanuwali, tyhala isilayida semveliso yetshaneli ukutshintsha ububanzi besignali yemveliso. Xa isetelwe kwi-othomathikhi, ububanzi besignali buya kwanda okanye bunciphe ngokuzenzekelayo.

Umjikelo : Umjikelo wemveliso yePWM. Uluhlu oluhlengahlengiswayo phakathi kwe-1ms-50ms.

1. Xa umjikelo umiselwe ngaphantsi kwe-2ms, ububanzi obuninzi abuyi kudlula ixabiso lomjikelo.
2. Isilayida esiphumayo setshaneli sikhuselekile. Akusayi kubakho mveliso yesignali de isilayidi sibuyiselwe kwindawo yaso encinci kuqala.

Isiphumo somqondiso wePPM

Ukusuka kwiphepha lemveliso ye-PWM, cofa okufutshane kwi-PWM ukutshintsha uhlobo lwemveliso; skrolela ngasekunene de iPPM ibonakale. Cinezela okufutshane ukuqinisekisa ukhetho lwePPM, njengoko kubonisiwe ngezantsi:

Kwiphepha lemveliso yePPM, cofa phantsi kwi-roller imizuzwana emi-2 ukuseta ixabiso lemveliso yetshaneli nganye.

1. Ijelo le-throttle lingalawulwa kuphela usebenzisa isignali ukusuka kwisilayidi esiphumayo; ixabiso alinakutshintshwa usebenzisa i-roller ngenxa yezizathu zokhuseleko.
2. Qinisekisa ukuba isilayida esiphumayo sikweyona ndawo isezantsi phambi kokuba wenze naluphi na uvavanyo.

Isiphumo sophawu lwe-SBUS

Ukusuka kwiphepha lemveliso ye-PWM, cofa okufutshane kwi-PWM ukutshintsha uhlobo lwemveliso; skrolela ngasekunene de i-SBUS ivele. Cinezela okufutshane ukuqinisekisa ukhetho lwe-SBUS, njengoko kubonisiwe ngezantsi:

Kwiphepha lemveliso ye-SBUS, cofa phantsi kwirola imizuzwana emi-2 ukuseta ixabiso lemveliso yetshaneli nganye.

1. Xa umjikelo umiselwe ngaphantsi kwe-2ms, ububanzi obuninzi abuyi kudlula ixabiso lomjikelo.
2. Isilayida esiphumayo setshaneli sikhuselekile. Akusayi kubakho mveliso yesignali de isilayidi sibuyiselwe kwindawo yaso encinci kuqala.

Ukutshaja kwe-USB

Izibuko ze-USB ezakhelwe ngaphakathi zivumela umsebenzisi ukuba ahlawule izixhobo eziphathwayo ekuhambeni. Izibuko le-USB-A libonelela nge-5V 1A ngelixa i-USB-C port ibonelela nge-20W ukutshaja ngokukhawuleza, isebenzisa ezi nkqubo zilandelayo: PD3.0, QC3.0, AFC, SCP, FCP njl.

Cinezela kwaye ubambe [Ivili] imizuzwana emi-2 ukungena kwimenyu yokuseta, unokuseta i-USB cutoff voltage. Xa ibhetri ikhupha ixabiso elimiselweyo, i-MC8 iya kucima zombini i-USB-A kunye ne-USB-C imveliso; i-buzzer iya kunika ithoni eyandisiweyo, ebonisa umthamo wokhuselekotage ifikelelwe.

Misela

Kwi-voltage ujongano, cofa kwaye ubambe [ivili] ukungena kwizicwangciso zesixokelelwano, njengoko kubonisiwe kumzobo ongezantsi:

Inkcazelo:

Ukhuseleko voltage: Xa ibhetri voltage ingaphantsi kweli xabiso, imveliso ye-USB iya kucinywa.
Isibane sangasemva: bonisa isicwangciso sokukhanya, ungacwangcisa i-1-10.
Ibhaza: Isandi esikhawulezayo sokusebenza, iitoni ezi-7 zinokusetwa okanye zicinywe.
Ulwimi: Ulwimi lwenkqubo, iilwimi ezibonisiweyo ezili-10 zinokukhethwa.
Isimbo somxholo: isimbo sokubonisa, ungacwangcisa imixholo eqaqambileyo nemnyama.
Ukuhlala kukho: Buyisela kulungiselelo lwasefektri.
Emva: Buyela kumqulutagujongano lovavanyo.
Isazisi: Inombolo eyodwa yesazisi yomatshini.

Ulungelelwaniso

Cinezela kwaye ubambe i-roller ngelixa unika amandla kwi-MC8 ukufaka imo yokulinganisa, njengoko kubonisiwe ngezantsi:

Ukulinganisa umthamotage yebhetri egcwaliswe ngokupheleleyo usebenzisa i-multimeter. Sebenzisa i-roller ukukhetha i-Input, uze uskrole de ixabiso lihambelane noko kulinganiswe kwi-multimeter. Skrolela ezantsi ukugcina kwaye ucinezele ezantsi kwirola ukuyigcina. Phinda le nkqubo kwiseli nganye ukuba kuyimfuneko. Xa ugqibile, skrolela kukhetho lokuphuma kwaye ucinezele phantsi kwirola ukugqiba ulungelelwaniso.

Igalelo: Umqulutage ilinganiswe kwizibuko eliphambili le-XT60.
1-8: Umqulutage yeseli nganye nganye.
I-ADC: Ixabiso loqobo lokhetho olukhethiweyo phambi kwecalib
Phuma: Phuma kwindlela yokulinganisa
Gcina: Gcina idatha yolungelelwaniso
Okuhlala kukho.: Buyela kuseto oluhlala lukhona

1. Sebenzisa kuphela i-multimeters ngokuchaneka kwe-0.001V ukwenza ulungelelwaniso. Ukuba i-multimeter ayichanekanga ngokwaneleyo, musa ukwenza ulungelelwaniso.

Iinkcukacha

Ngokubanzi	Izibuko longeniso olungundoqo	XT60 7.0V-35.0V
	Igalelo lokulinganisela	0.5V-5.0V Lit 2-85
	Ungeniso lwezibuko lomqondiso	<6.0V
	Ibhalansi yangoku	MAX 60mA 02-85
	Ibhalansi ukuchaneka	<0.005V 0 4.2V
	Imveliso ye-USB-A	5.0V@1.0A uphuculo lwe-firmware
	Imveliso ye-USB-C	5.0V-12.0V @MAX 20W
	Iprotocol ye-USB-C	PD3.0 QC3.0 AFC SCP FCP
Umlinganiselo ingqondo	PWM	500-2500us 020-400Hz
	PPM	880-2200uss8CH @20-50Hz
	SBUS	880-2200us * 16CH @20-100Hz
Isiphumo	PWM	1000-2000us @20-1000Hz
	PPM	880-2200us * 8CH @50Hz
	SBUS	880-2200us * 16CH @ 74Hz
Imveliso	Ubungakanani	68mm*50mm*15mm
	Ubunzima	50g
Iphakheji	Ubungakanani	76mm*60mm*30mm
	Ubunzima	1009
LCD		IPS 2.0 intshi 240°240 isisombululo

 

Amaxwebhu / Izibonelelo

ToolkitRC MC8 iBattery Checker enomboniso weLCD [pdf] Incwadi yokusebenzisa MC8, iBattery Checker ene-LCD Display, iMC8 iBattery Checker ene-LCD Display

Iimbekiselo

• Incwadi yokusebenzisa