ToolkitRC MC8 Baturi Checker tare da LCD Nuni Mai amfani Manual
ToolkitRC MC8 Baturi Checker tare da LCD Nuni

Abubuwan da ke ciki boye
1 Gabatarwa
2 Gumakan hannu
3 Ƙarin bayani
4 Kariyar tsaro
5 Samfurin ya ƙareview
6 Tsarin tsari
7 Amfani na farko
8 Voltage gwajin
9 Ma'aunin sigina
10 Fitowar sigina
11 Cajin USB
12 Saita
13 Daidaitawa
14 Ƙayyadaddun bayanai
15 Takardu / Albarkatu
15.1 Magana
16 Labarai masu alaka

Gabatarwa

Na gode don siyan MC8 Multi-checker. Da fatan za a karanta wannan littafin a hankali kafin a fara aiki da na'urar.

Gumakan hannu

  • Ikon Tukwici
  • Ikon faɗakarwa Muhimmanci
  • Ikon Sunayen suna

Ƙarin bayani

Don ƙarin bayani game da aiki da kula da na'urar ku, da fatan za a ziyarci hanyar haɗin yanar gizon: www.toolkitrc.com/mc8

Kariyar tsaro

  1. Ayyukan aiki voltage na MC8 yana tsakanin DC 7.0V da 35.0V. Tabbatar cewa ba a juyar da polarity na tushen wutar kafin amfani ba.
  2. Kada a yi aiki a ƙarƙashin matsanancin zafi, zafi, mai ƙonewa da mahalli masu fashewa.
  3. Kar a taɓa barin babu kula lokacin da ake aiki.
  4. Cire haɗin tushen wutar lantarki lokacin da ba a amfani da shi

Samfurin ya ƙareview

MC8 ƙaramin mai duba ne wanda aka tsara don kowane mai sha'awar sha'awa. Yana nuna nunin IPS mai haske, launi, daidai yake da 5mV

  • Ma'auni da ma'auni LiPo, LiHV, LiFe da baturan zaki.
  • Mai girma voltage shigar da DC 7.0-35.0V.
  • Yana goyan bayan manyan abubuwan shigar da wutar lantarki na Babban/Ma'auni/Sigina.
  • Aunawa da fitar da siginar PWM, PPM, SBUS.
  • USB-A, fitarwa na USB-C dual-port.
  • USB-C 20W PD saurin cajin fitarwa.
  • Kariyar yawan fitar da baturi. Yana kashe fitarwa ta USB ta atomatik lokacin da baturi ya kai matakai masu mahimmanci.
  • Ma'auni da daidaiton ma'auni: <0.005V.
  • Ma'auni na yanzu: 60mA.
  • 2.0 inch, IPS cikakke viewnunin kusurwa.
  • Babban ƙuduri 320*240 pixels.

Tsarin tsari

Gaba
Samfurin Ƙarsheview

Na baya
Samfurin Ƙarsheview

Amfani na farko

  1. Haɗa baturin zuwa tashar ma'auni na MC8, ko haɗa 7.0-35.0V voltage zuwa tashar shigarwar XT60 na MC8.
  2. Allon yana nuna alamar taya don 0.5 seconds
  3. Bayan an gama boot ɗin, allon yana shiga babban wurin dubawa kuma yana nunawa kamar haka:
    Nunawa
  4. Juya abin nadi don gungurawa tsakanin menus da zaɓuɓɓuka.
  5. Gajere ko dogayen latsa abin nadi don shigar da abu
  6. Yi amfani da faifan fitarwa don daidaita fitowar tashar.

Ikon Aikin gungurawa daban don abubuwan menu daban-daban, da fatan za a koma zuwa umarni masu zuwa.

Voltage gwajin

Voltage nuni da daidaituwa (kwayoyin mutum ɗaya)

Haɗa tashar ma'auni na baturin zuwa MC8. Bayan na'urar ta kunna, babban shafin yana nuna voltage na kowane cell-kamar yadda aka nuna a kasa:

Sanduna masu launin suna nuna voltage na baturin graphically. Tantanin halitta tare da mafi girman voltage yana nunawa da ja, yayin da tantanin halitta mai mafi ƙanƙanta voltage yana nunawa da shuɗi. Jimlar voltage da voltage bambanci (mafi girma voltage-mafi ƙanƙanta voltage) aka nuna a kasa.

A babban menu, danna [dabaran] don fara aikin ma'auni. MC8 yana amfani da resistors na ciki don fitar da tantanin halitta har sai fakitin ya kai daidaitaccen voltage tsakanin sel (<0.005V bambanci)

  1. Ikon An daidaita sandunan don LiPOs, ba daidai ba ne ga batura tare da sauran sunadarai.
  2. Bayan daidaita fakitin baturi, cire baturin daga MC8 don hana fitar da yawa

Fakitin baturi jimlar voltage

Haɗa jagorar baturi zuwa babban tashar jiragen ruwa na XT60 akan MC8 don nuna jimlar voltage na fakitin baturi, kamar yadda aka nuna a kasa.

Nunawa

  1. Ikon MC8 yana nuna jimlar voltage na duk sinadarai na baturi da ke aiki tsakanin iyakokin shigarwa.

Ma'aunin sigina 

Ma'aunin siginar PWM

Bayan na'urar ta kunna, gungura dama sau ɗaya akan abin nadi na ƙarfe don shigar da yanayin Aunawa. Ana nuna shafin kamar haka.

Ma'aunin siginar PWM
Bayanin UI
PWM: Nau'in sigina
1500: Yanzu Faɗin bugun bugun jini na PWM
20ms/5 Hz ： Zagayowar yanzu da mitar siginar PWM

  1. Lokacin amfani da aikin auna sigina. Tashar tashar siginar, tashar ma'auni, da babban tashar shigarwar duk na iya ba da wuta ga MC8

Ma'aunin siginar PPM

A ƙarƙashin yanayin auna siginar PWM, danna ƙasa akan gungurawa kuma gungura dama har sai an nuna PPM. Sannan ana iya auna siginar PPM, kamar yadda aka nuna a ƙasa.

Ma'aunin siginar PPM

Ma'aunin siginar SBUS

A ƙarƙashin yanayin auna siginar PWM, danna ƙasa akan gungurawa kuma gungura dama har sai an nuna SBUS. Sannan ana iya auna siginar SBUS, kamar yadda aka nuna a kasa.

Ma'aunin siginar PPM

Fitowar sigina

Fitowar siginar PWM

Tare da kunna MC8, gungura dama sau biyu akan abin nadi don shigar da yanayin fitarwa. Danna ƙasa a kan gungurawa na tsawon daƙiƙa 2 don shigar da yanayin fitarwar sigina, kamar yadda aka nuna a ƙasa. Bayanin UI

Fitowar sigina

Yanayin ： Yanayin fitarwa na sigina- za'a iya canza shi tsakanin tsarin jagora da 3 ta atomatik na saurin gudu.

Nisa ： PWM siginar fitarwa bugun jini nisa, iyaka iyaka 1000us-2000us. Lokacin da aka saita zuwa jagora, tura madaidaicin fitarwa ta tashar don canza faɗin siginar fitarwa. Lokacin saita zuwa atomatik, faɗin siginar zai ƙaru ko raguwa ta atomatik.

Zagayowar ：PWM sake zagayowar fitarwa. Matsakaicin iyaka tsakanin 1ms-50ms.

  1. Ikon Lokacin da aka saita zagayowar zuwa ƙasa da 2ms, matsakaicin faɗin ba zai wuce ƙimar zagayowar ba.
  2. Ana kariyar dalla-dalla mai fitarwa ta tashar. Ba za a sami fitowar sigina ba har sai an dawo da silsilar zuwa mafi ƙarancin matsayinsa da farko.

Fitowar siginar PPM

Daga shafin fitarwa na PWM, gajeriyar danna kan PWM don canza nau'in fitarwa; gungura dama har sai an nuna PPM. Taƙaitaccen latsa don tabbatar da zaɓin PPM, kamar yadda aka nuna a ƙasa:

Fitowar siginar PPM

A cikin shafin fitarwa na PPM, danna ƙasa a kan abin nadi na tsawon daƙiƙa 2 don saita ƙimar fitarwa na kowane tashoshi.

  1. Ikon Za a iya sarrafa tashar maƙura kawai ta amfani da sigina daga madaidaicin fitarwa; Ba za a iya canza ƙimar ta amfani da abin nadi don dalilai na aminci ba.
  2. Tabbatar cewa madaidaicin fitarwa yana a mafi ƙanƙancinsa kafin yin kowane gwaji.

Fitowar siginar SBUS

Daga shafin fitarwa na PWM, gajeriyar danna kan PWM don canza nau'in fitarwa; gungura dama har sai an nuna SBUS. Taƙaitaccen latsa don tabbatar da zaɓin SBUS, kamar yadda aka nuna a ƙasa:

Fitowar siginar SBUS

A cikin shafin fitarwa na SBUS, danna ƙasa a kan abin nadi na tsawon daƙiƙa 2 don saita ƙimar fitarwa na kowane tashoshi.

  1. Lokacin da aka saita zagayowar zuwa ƙasa da 2ms, matsakaicin faɗin ba zai wuce ƙimar zagayowar ba.
  2. Ana kariyar dalla-dalla mai fitarwa ta tashar. Ba za a sami fitowar sigina ba har sai an dawo da silsilar zuwa mafi ƙarancin matsayinsa da farko.

Cajin USB

Gina-ginen tashoshin USB suna ba mai amfani damar yin cajin na'urorin hannu yayin tafiya. Tashar USB-A tana ba da 5V 1A yayin da tashar USB-C ke ba da cajin sauri na 20W, ta amfani da ka'idoji masu zuwa: PD3.0, QC3.0, AFC, SCP, FCP da sauransu.

Cajin USB

Latsa ka riƙe [Wheel] 2 seconds don shigar da menu na saiti, zaka iya saita kebul na yanke voltage. Lokacin da baturi ya fita ya wuce ƙimar saita, MC8 zai kashe duka USB-A da USB-C; mai buzzer kuma zai ba da sauti mai tsayi, yana nuni da voltagan kai e.

Nunawa

Saita

A kan voltage dubawa, latsa ka riƙe [dabaran] don shigar da saitunan tsarin, kamar yadda aka nuna a cikin hoton da ke ƙasa:

Saita

Bayani:

Tsaro voltage: Lokacin da baturi voltage ya yi ƙasa da wannan ƙimar, za a kashe fitarwar USB.
Hasken Baya: nuni saitin haske, zaka iya saita 1-10 .
Kuka: Sautin gaggawar aiki, sautuna 7 za'a iya saita ko kashe su.
Harshe: Harshen tsarin, ana iya zaɓar harsunan nuni 10.
Salon jigo: salon nuni, zaku iya saita jigogi masu haske da duhu.
Na baya: Mayar da saitin masana'anta.
Baya: Koma zuwa voltage gwajin dubawa.
ID: Lambar ID na musamman na injin.

Daidaitawa

Latsa ka riƙe abin nadi yayin da kake kunna MC8 don shigar da yanayin daidaitawa, kamar yadda aka nuna a ƙasa:

Daidaitawa

Auna voltage na fakitin baturi mai cikakken caji ta amfani da multimeter. Yi amfani da abin nadi don zaɓar Input, sannan gungura har sai ƙimar ta yi daidai da abin da aka auna akan multimeter. Gungura ƙasa don ajiyewa kuma danna ƙasa a kan abin nadi don ajiyewa. Maimaita wannan tsari ga kowane tantanin halitta idan an buƙata. Lokacin da aka gama, gungura zuwa zaɓin fita kuma danna ƙasa akan abin nadi don gama daidaitawa.

Shigarwa: Voltage auna a babban tashar jiragen ruwa XT60.
1-8: Voltage na kowane kwayar halitta.
ADC: Asalin ƙimar zaɓin da aka zaɓa kafin calib
Fita: Fita yanayin daidaitawa
Ajiye: Ajiye bayanan daidaitawa
Na asali.: Koma zuwa saitunan tsoho

  1. Ikon Yi amfani da multimeters kawai tare da daidaiton 0.001V don yin ƙira. Idan multimeter bai isa ba, kar a yi calibration.

Ƙayyadaddun bayanai

Gabaɗaya Babban tashar shigar da bayanai XT60 7.0V-35.0V
Shigar da ma'auni 0.5V-5.0V Lit 2-85
Shigar da tashar tashar sigina <6.0V
Daidaita halin yanzu MAX 60mA 02-85
Ma'auni
daidaito		 <0.005V 0 4.2V
USB-A fitarwa 5.0V@1.0A haɓaka firmware
USB-C fitarwa 5.0V-12.0V @MAX 20W
USB-C yarjejeniya PD3.0 QC3.0 AFC SCP FCP
Auna
ment		 PWM 500-2500us 020-400Hz
PPM 880-2200uss8CH @20-50Hz
SBUS 880-2200us *16CH
@20-100Hz
Fitowa PWM 1000-2000us @ 20-1000Hz
PPM 880-2200us*8CH @50Hz
SBUS 880-2200us *16CH @74Hz
Samfura Girman 68mm*50*15mm
Nauyi 50 g
Kunshin Girman 76mm*60*30mm
Nauyi 1009
LCD IPS 2.0 inch 240°240
ƙuduri

 

Takardu / Albarkatu

ToolkitRC MC8 Baturi Checker tare da LCD Nuni [pdf] Manual mai amfani
MC8, Baturi Checker tare da LCD Nuni, MC8 Baturi Checker tare da LCD Nuni

Magana

Labarai masu alaka

Bar sharhi

Ba za a buga adireshin imel ɗin ku ba. Ana yiwa filayen da ake buƙata alama *