ToolkitRC MC8 Battery Checker ine LCD Ratidza Mushandisi Manual

Nhanganyaya

Ndatenda nekutenga MC8 yakawanda-checker. Ndapota verenga bhuku rino zvakanyatsonaka usati washandisa mudziyo.

Manual icons

• Zano
• Zvakakosha
• Nomenclature

Mamwe mashoko

Kuti uwane rumwe ruzivo nezve mashandisirwo nekugadzirisa kwechigadzirwa chako, ndapota shanyira iyi link: www.toolkitrc.com/mc8

Kuchengetedza kuchengetedza

1. The operational voltage yeMC8 iri pakati peDC 7.0V ne35.0V. Ita shuwa kuti polarity yesimba sosi haina kudzoserwa isati yashandiswa.
2. Usashande pasi pekupisa kwakanyanya, mwando, nzvimbo dzinopisa uye dzinoputika.
3. Usambofa wakasiya usina kutarisirwa paunenge uchishanda.
4. Bvisa panobva magetsi kana isiri kushandiswa

Chigadzirwa pamusoroview

Iyo MC8 ndeye compact yakawanda-checker yakagadzirirwa yega yega hobbyist. Inoratidzira yakajeka, ine ruvara IPS kuratidza, ndeyechokwadi kune 5mV

• Zviyero uye zviyero LiPo, LiHV, LiFe uye Shumba mabhatiri.
• Wide voltage kupinza DC 7.0-35.0V.
• Inotsigira Main/Balance/Signal port power inputs.
• Zviyero uye zvinobuda PWM, PPM, SBUS masiginecha.
• USB-A, USB-C mbiri-chiteshi kubuda.
• USB-C 20W PD kukurumidza kuchaja kubuda.
• Battery over-discharge protection. Inodzima otomatiki kubuda kwe USB kana bhatiri rasvika pamazinga akakosha.
• Kuyera uye chiyero chechokwadi: <0.005V.
• Chiyero ikozvino: 60mA.
• 2.0 inch, IPS yakazara viewing angle kuratidza.
• High resolution 320 * 240 pixels.

Layout

Mberi

Rear

Kutanga kushandiswa

1. Batanidza bhatiri pachiyero cheMC8, kana batanidza 7.0-35.0V voltage kune XT60 yekupinza chiteshi cheMC8.
2. Iyo skrini inoratidza bhutsu logo ye 0.5 masekondi
3. Mushure mekunge bhutsu yapera, skrini inopinda mukati meiyo huru interface uye inoratidza seinotevera:
   
4. Shandura roller kuti ifambe pakati pemamenu uye sarudzo.
5. Mupfupi kana kureba dzvanya roller kuti uise chinhu
6. Shandisa inobuda inotsvedza kugadzirisa chiteshi chinobuda.

Iyo scroller inoshanda zvakasiyana kune akasiyana menyu zvinhu, ndapota tarisa kune inotevera mirairo.

Voltage test

Voltage kuratidza uye kuenzanisa (masero ega ega)

Batanidza chiteshi chebhatiri kune MC8. Mushure mekunge mudziyo wabatidzwa, peji guru rinoratidza voltage yesero rega rega- sezvaratidzwa pazasi:

Iwo mavara ane mavara anoratidza voltage yebhatiri zvine graphic. Sero rine vhoriyamu yepamusorosorotage inoratidzwa mutsvuku, ukuwo sero rine vhoriyamu yakadereratage inoratidzwa neblue. Zvose voltage uye voltage musiyano (repamusoro voltage-yakaderera voltage) inoratidzwa pasi apa.

Pamenu huru, dzvanya [vhiri] kuti utange basa rekuenzanisa. Iyo MC8 inoshandisa zvinopikisa zvemukati kuburitsa sero (ma) kusvika paki yasvika payunifomu voltage pakati pemasero (<0.005V musiyano)

1. Mabhawa akatemerwa LiPOs, haina chokwadi kune mabhatiri ane mamwe machemistries.
2. Mushure mekuenzanisa bhatiri paki, bvisa bhatiri kubva paMC8 kudzivirira kubuda zvakanyanya

Battery pack yakazara voltage

Batanidza bhatiri rinotungamira kune hombe XT60 chiteshi paMC8 kuratidza yakazara voltage yebhatiri pack, sezvakaratidzwa pasi apa.

1. Iyo MC8 inoratidza iyo yakazara voltage yeese mabhatiri chemistries anoshanda mukati memiganho yekupinza.

Chiyero chechiratidzo 

PWM Chiratidzo kuyerwa

Mushure mekunge mudziyo wabatidzwa, penya kamwe chete pane simbi roller kuti upinde Measure mode. Peji yacho inoratidzwa sezvinotevera.

UI tsananguro
PWM: Signal type
1500: Iyezvino PWM pulse width
20ms/5Hz : Yazvino kutenderera uye kuwanda kwePWM chiratidzo

1. Paunenge uchishandisa chiratidzo chekuyera basa. Iyo chiratidzo chechiteshi, chiyero chechiteshi, uye hombe yekupinza chiteshi zvese zvinogona kupa simba kuMC8

PPM chiratidzo chekuyera

Pazasi pePWM siginecha yekuyera modhi, dzvanya pasi pane yeku scroller uye skrota kurudyi kusvika PPM yaratidzwa. Ipapo chiratidzo chePPM chinogona kuyerwa, sezvakaratidzwa pasi apa.

SBUS Chiratidzo kuyerwa

Pasi pePWM siginecha yekuyera modhi, dzvanya pasi pachina cheku scroller uye wobva wadzvanya kurudyi kusvika SBUS yaratidzwa. Ipapo chiratidzo cheSBUS chinogona kuyerwa, sezvakaratidzwa pasi apa.

Signal output

PWM Signal kubuda

Uine MC8 yakabatidzwa, penya kaviri pane roller kuti uise Output mode. Dzvanya pasi pane scroller kwemasekonzi maviri kuti uise chiratidzo chekubuda modhi, sezvakaratidzwa pazasi. UI Tsanangudzo

Mamiriro: Signal yekubuda mode- inogona kuchinjwa pakati pemanyorero uye 3 otomatiki modhi yekumhanya kwakasiyana.

Upamhi : PWM chiratidzo chinobuda pulse hupamhi, muganho wepakati 1000us-2000us. Kana yaiswa kumanyorero, sundidzira chiteshi chinobuda chinotsvedza kuti uchinje hupamhi hwechiratidzo chekubuda. Kana yaiswa otomatiki, hupamhi hwechiratidzo huchawedzera kana kudzikira.

Cycle : PWM chiratidzo chekubuda kutenderera. Range inogadziriswa pakati pe1ms-50ms.

1. Kana iyo denderedzwa yakaiswa kune isingasviki 2ms, iyo yakakura hupamhi haizopfuure kukosha kwekutenderera.
2. Iyo chiteshi inoburitsa slider yakachengetedzwa yakachengetedzwa. Pachave pasina chiratidzo chinobuda kudzamara iyo inotsvedza yadzoserwa kunzvimbo yayo shoma kutanga.

PPM Signal kubuda

Kubva pane peji rekubuda rePWM, dzvanya pfupi paPWM kuti uchinje mhando yekubuda; skiritsa kurudyi kusvika PPM yaratidzwa. Kudzvanya pfupi kuti usimbise kusarudzwa kwePPM, sezvakaratidzwa pazasi:

Mune peji rePPM rinobuda, dzvanya pasi pane roller kwemasekonzi maviri kuseta kukosha kwekubuda kwechiteshi chega chega.

1. Iyo throttle chiteshi inogona chete kudzorwa uchishandisa chiratidzo kubva kune inobuda inotsvedza; kukosha hakugone kuchinjwa uchishandisa roller nekuda kwezvikonzero zvekuchengetedza.
2. Ita shuwa kuti inotsvedza inobuda iri panzvimbo yayo yakaderera isati yaita chero bvunzo.

SBUS chiratidzo chinobuda

Kubva pane peji rekubuda rePWM, dzvanya pfupi paPWM kuti uchinje mhando yekubuda; skroka kurudyi kusvika SBUS yaratidzwa. Kudzvanya pfupi kuti usimbise iyo SBUS kusarudzwa, sezvakaratidzwa pazasi:

Muiyo SBUS yakabuda peji, dzvanya pasi pa roller kwemasekonzi maviri kuseta kukosha kwekubuda kwechiteshi chega chega.

1. Kana iyo denderedzwa yakaiswa kune isingasviki 2ms, iyo yakakura hupamhi haizopfuure kukosha kwekutenderera.
2. Iyo chiteshi inoburitsa slider yakachengetedzwa yakachengetedzwa. Pachave pasina chiratidzo chinobuda kudzamara iyo inotsvedza yadzoserwa kunzvimbo yayo shoma kutanga.

USB kuchaja

Yakavakirwa-mukati USB madoko inobvumira mushandisi kuchaja nharembozha paunenge uchienda. Iyo USB-A port inopa 5V 1A nepo USB-C chiteshi ichipa 20W nekukurumidza kuchaja, uchishandisa anotevera maprotocol: PD3.0, QC3.0, AFC, SCP, FCP nezvimwe.

Dzvanya uye ubate [Wheel] 2 masekonzi kuti uise iyo yekuseta menyu, unogona kuseta iyo USB cutoff voltage. Kana bhatiri richibuda kupfuura kukosha kweseti, iyo MC8 inodzima zvese USB-A uye USB-C kubuda; iyo buzzer ichapawo inzwi rakawedzerwa, richiratidza kudzivirira voltage yasvikwa.

Gadzirira

Pamusoro pevoltage interface, dzvanya uye ubate [vhiri] kuti upinde masisitimu marongero, sezvakaratidzwa pamufananidzo pazasi:

Tsanangudzo:

Safety voltage: Kana bhatiri voltage yakaderera pane iyi kukosha, iyo USB inobuda ichadzimwa.
Backlight: kuratidza kupenya kurongedza, unogona kuseta 1-10 .
Buzzer: Kushanda nekukurumidza ruzha, 7 toni dzinogona kusetwa kana kudzimwa.
Mutauro: Mutauro weSisitimu, mitauro gumi inoratidzwa inogona kusarudzwa.
Theme style: kuratidza maitiro, unogona kuseta akajeka uye akasviba matema.
Default: Dzosera kugadziriro yepafekitari.
Kumashure: Dzokera kune voltaguye test interface.
ID: Iyo yakasarudzika ID nhamba yemuchina.

Calibration

Dzvanya uye ubate roller uchisimbisa paMC8 kuti uise calibration mode, sezvinoratidzwa pazasi:

Kuyera voltage ye-yakazara-chaji bhatiri paki uchishandisa multimeter. Shandisa roller kusarudza Input, wobva wapuruzira kusvika kukosha kwaenderana nezvakayerwa pamultimeter. Skroka pasi kuti uchengetedze uye wodzvanya pasi pane roller kuti uchengetedze. Dzokorora maitiro aya kune yega yega sero kana zvichidikanwa. Kana wapedza, skira kune yekubuda sarudzo uye dzvanya pasi pane roller kuti upedze kugadzirisa.

Input: Voltagakayerwa pachiteshi chikuru cheXT60.
1-8: Voltage yega yega sero.
ADCs: Kukosha kwepakutanga kwesarudzo yakasarudzwa pamberi pe calib
Buda: Buda kugadzirisa maitiro
Sevha: Sevha data yekuenzanisa
Default.: Dzokera kune zvigadziriso zvinogara zviripo

1. Ingoshandisa mamultimeters ane 0.001V kunyatsoita macalibrations. Kana iyo multimeter isina kukwana zvakakwana, usaite calibration.

Zvinotsanangurwa

General	Nzvimbo huru yekupinda	XT60 7.0V-35.0V
	Balance input	0.5V-5.0V Lit 2-85
	Signal port input	<6.0V
	Balance current	MAX 60mA 02-85
	Balance kururama	<0.005V 0 4.2V
	USB-A inobuda	5.0V@1.0A firmware upgrade
	USB-C kubuda	5.0V-12.0V @MAX 20W
	USB-C protocol	PD3.0 QC3.0 AFC SCP FCP
Kuyera ment	PWM	500-2500us 020-400Hz
	PPM	880-2200uss8CH @20-50Hz
	SBUS	880-2200us *16CH @20-100Hz
Output	PWM	1000-2000us @20-1000Hz
	PPM	880-2200us*8CH @50Hz
	SBUS	880-2200us *16CH @74Hz
Product	Size	68mm*50mm*15mm
	Kurema	50g
Package	Size	76mm*60mm*30mm
	Kurema	1009
LCD		IPS 2.0 inch 240°240 resolution

 

Zvinyorwa / Zvishandiso

ToolkitRC MC8 Battery Checker ine LCD Ratidza [pdf] User Manual MC8, Battery Checker ine LCD Display, MC8 Battery Checker ine LCD Display

References

• User Manual