i-microsonic pico+15-TF-I Inzwa ye-Ultrasonic enePhumo elinye le-Analogue
Ulwazi lweMveliso
Isivamvo se-Ultrasonic esinePhumo elinye le-Analogue
I-Ultrasonic Sensor ene-One Analogue Output ifumaneka kwiimodeli ezine ezahlukeneyo: pico+15/TF/I, pico+25/TF/I, pico+35/TF/I, kunye ne-pico+100/TF/I. Ukongeza, kukho ezinye iimodeli ezine ezineenkcukacha ezahlukeneyo: pico+15/TF/U, pico+25/TF/U, pico+35/TF/U, kunye pico+100/TF/U. I-sensor isetyenziselwa ukufumanisa izinto ezingabonakaliyo kwaye inendawo eyimfama ye-20mm kunye noluhlu olusebenzayo lwe-150mm ukuya kwi-250mm ngokuxhomekeke kwimodeli. I-transducer frequency yi-380kHz kwaye isisombululo yi-0.069mm. I-action pin yeplagi yoluvo iboniswe kuMfanekiso woku-1.
Idatha yoBugcisa
| Umzekelo | Indawo eyimfama | Uluhlu lokuSebenza | Uluhlu oluphezulu | Transducer Frequency | Isigqibo |
|---|---|---|---|---|---|
| ipico+15 | 20mm | 150mm | 250mm | 380kHz | 0.069mm |
| ipico+25 | 20mm | 350mm | 250mm | bona indawo yokufumanisa | 0.069 ukuya kwi-0.10mm |
| ipico+35 | 20mm | bona indawo yokufumanisa | bona indawo yokufumanisa | 320kHz | 0.069 ukuya kwi-0.10mm |
| ipico+100 | 20mm | 0.4m | 0m ukuya kwi-4m (i-5mm yokuqala ayikhuthazwa ukuba ifakwe) | 320kHz | 0.069 ukuya kwi-0.10mm |
Imiyalelo yokusetyenziswa kwemveliso
- Funda incwadi yokusebenza phambi kokuba uqalise.
- Uqhagamshelo, ufakelo, kunye nohlengahlengiso lunokwenziwa kuphela ngabasebenzi abafanelekileyo.
- Akukho candelo lokhuseleko ngokuhambelana ne-EU Machine Directive, ukusetyenziswa kwindawo yokhuseleko lomntu kunye nomatshini akuvumelekanga.
- Yisebenzisele injongo kuphela.
- Kwi-pico + 100/TF, ungayisebenzisi ekufakeni i-5mm yokuqala yentambo ye-M22 kwicala le-transducer.
- Seta iiparamitha zoluvo usebenzisa inkqubo yokuFundisa usebenzisa iSazobe soku-1:
- Cwangcisa imveliso ye-analog ngokubeka into kwindawo yoku-1 kunye nokudibanisa i-Com malunga ne-3s ukuya ku-+UB de zombini ii-LED zidanya ngaxeshanye.
- Cwangcisa imida yefestile ngokubeka into kwindawo yesi-2 kunye nokudibanisa iCom malunga no-1 ukuya ku-+UB, uze udibanise iCom malunga ne-13s ukuya ku +UB de zombini ii-LED zidanya ngokutshintshanayo.
- Cwangcisa igophe eliphumayo elinyukayo/elihlayo ngokuqhagamshela iCom malunga no-1s ukuya +UB.
- Ukutshintsha iimpawu zemveliso, qhagamshela iCom malunga no-1 ukuya ku-+UB.
- Phinda umisele useto lwasefektri ngokucima unikezelo lombane, emva koko utshintshe unikezelo lombane de zidanyaze zombini ii-LED ngaxeshanye. I-LED eluhlaza ibonisa i-Teach-in kunye ne-Yellow LED ibonisa i-Sync.
- Iinzwa zosapho lwePico + zinendawo eyimfama. Kulo mmandla, umlinganiselo womgama awunakwenzeka.
- Ngalo lonke ixesha ukunikezelwa kwamandla kuguqulwa, inzwa ibona ukushisa kwayo kwangempela kwaye idlulisele kwimbuyekezo yeqondo lokushisa langaphakathi. Ixabiso elilungisiweyo lithathwa emva kwemizuzwana ye-120.
- Kwimowudi yokusebenza eqhelekileyo, i-LED ekhanyisiweyo ephuzi ibonisa ukuba into ingaphakathi kwimida yefestile ehlengahlengisiweyo.
Incwadi yokuSebenza
Inzwa ye-Ultrasonic enemveliso enye ye-analog
- pico+15/TF/I
- pico+15/TF/U
- pico+25/TF/I
- pico+25/TF/U
- pico+35/TF/I
- pico+35/TF/U
- pico+100/TF/I
- pico+100/TF/U
Ingcaciso yeMveliso
I-sensor ye-pico + inikezela ngomlinganiselo ongaqhagamshelwanga womgama ukuya kwinto ekufuneka ibekho ngaphakathi kwendawo yokufumanisa i-sensor. Ngokuxhomekeke kwimida yefestile yezicwangciso, isignali ye-analog yomgama iyaphuma. I-ultrasonic transducer surface ye-pico+ sensors ilayitiwe ngefilimu ye-PTFE. I-transducer ngokwayo itywinwe ngokuchasene nendlu ngendandatho edibeneyo. Olu qulunqo luvumela umlinganiselo ukuya kuthi ga kwi-0,5 bar overpressure. Imida yefestile yemveliso ye-analog kunye neempawu zayo zinokuhlengahlengiswa ngokusebenzisa inkqubo yokuFundisa. Ii-LED ezimbini zibonisa ukusebenza kunye nemeko yemveliso ye-analog.
Imiyalelo yokhuseleko
- Funda incwadi yokusebenza phambi kokuba uqalise.
- Uqhagamshelo, ufakelo, kunye nohlengahlengiso lunokwenziwa kuphela ngabasebenzi abafanelekileyo.
- Akukho candelo lokhuseleko ngokuhambelana ne-EU Machine Directive, ukusetyenziswa kwindawo yokhuseleko lomntu kunye nomatshini akuvumelekanga.
Yisebenzisele injongo kuphela
I-pico + i-ultrasonic sensors isetyenziselwa ukuchongwa kwezinto ezingadibanisiyo.
Ukuhlohla
- Nyuka isivamvo kwindawo yokulinganisa. Kwi-pico + 100/TF, sincoma ukuba ungasebenzisi ukunyuswa kwe-5 mm yokuqala yentambo ye-M22 kwicala le-transducer.
- Qhagamshela intambo yoqhagamshelo kwiplagi yesixhobo seM12, jonga umfanekiso 1.
|
|
 |
umbala |
| 1 | +UB | ntsundu |
| 3 | –UB | luhlaza |
| 4 | – | mnyama |
| 2 | I/U | mhlophe |
| 5 | Com | ngwevu |
Pin isabelo nge view kwiplagi yesivamvo kunye nekhowudi yombala yeentambo zoqhagamshelo ezincinci
Ukuqala eqala
- Qhagamshela unikezelo lwamandla.
- Yenza uhlengahlengiso lwenzwa ngokuhambelana neSazobe soku-1.
Ulungiselelo lwasefektri
- Ijika leempawu ze-analog ezikhulayo phakathi kwendawo eyimfama kunye noluhlu lokusebenza.
- Igalelo lemisebenzi emininzi »Com« isete ku»Fundisa ngaphakathi«.
Ungqamaniso
Ukuba umgama wendibano uwela ngaphantsi kwamaxabiso aboniswe kwi-Fig. 2, ulungelelwaniso lwangaphakathi kufuneka lusetyenziswe. Ngenxa yale njongo misela iziphumo ezitshintshiweyo zazo zonke izinzwa ngokuhambelana neSazobe soku-1 ekuqaleni. Emva koko cwangcisa imveliso esebenzayo »Com« ukuya »ungqamaniso« (bona »Ezinye iisetingi«, Idiagram 1). Okokugqibela, qhagamshela i-pin 5 yeplagi yabenzi boluvo bazo zonke izinzwa.
Isondlo
abenzi boluvo beMikroskopu balulondolozwe simahla. Kwimeko yokungcola okugqithisileyo, sincoma ukucoca indawo emhlophe yoluvo.
 |
 |
|
| ipico+15... | ³0.25 m | ³1.30 m |
| ipico+25... | ³0.35 m | ³2.50 m |
| ipico+35... | ³0.40 m | ³2.50 m |
| ipico+100... | ³0.70 m | ³4.00 m |
Imigama yeNdibano.
Amanqaku
- Iinzwa zosapho lwePico + zinendawo eyimfama. Kulo mmandla, umlinganiselo womgama awunakwenzeka.
- Ngalo lonke ixesha ukunikezelwa kwamandla kuguqulwa, inzwa ibona ukushisa kwayo kwangempela kwaye idlulisele kwimbuyekezo yeqondo lokushisa langaphakathi. Ixabiso elilungisiweyo lithathwa emva kwemizuzwana ye-120.
- Kwimo yokusebenza eqhelekileyo, i-yellow ekhanyisiweyo ye-LED imiqondiso into ingaphakathi kwimida yefestile ehlengahlengisiweyo.
- Ukuba ungqamaniso lwenziwe lwasebenza i-Fundisa-ngaphakathi ivaliwe (jonga »Ezinye iisetingi«, Idayagram 1).
- Uluvo lunokusetwa kwakhona kwisetingi yayo yefektri (bona »Ezinye iisetingi«, Idayagram 1).
- Ngokuzikhethela zonke i-Teach-in kunye nesetingi ezongezelelweyo zeparameter zenzwa zingenziwa ngokusebenzisa i-adapter ye-LinkControl (i-accessory yokuzikhethela) kunye ne-software ye-LinkControl ye-Windows ©.
Cwangcisa iiparamitha zoluvo usebenzisa inkqubo yokuFundisa ngaphakathi
Cwangcisa imveliso ye-analog
| Cwangcisa imida yefestile | Cwangcisa igophe eliphumayo elinyukayo/elihlayo | |||
| Beka into kwindawo yoku-1. | ||||
| Qhagamshela iCom malunga ne-3 s ukuya +UB, de zibe zombini ii-LEDs zidanyaze ngaxeshanye. | Qhagamshela iCom malunga ne-13 s ukuya +UB, de zibe zombini ii-LEDs zidanyaze ngokutshintshanayo. | |||
| Zombini ii-LED: | khanyisa ngokunye | I-LED eluhlaza:
I-LED etyheli: |
idanyaza
on: ukunyuka icimile: ijika leempawu eziwayo |
|
| Beka into kwindawo yoku-2. | ||||
|
Qhagamshela iCom malunga no1s ukuya +UB. |
Ukutshintsha uphawu lwemveliso qhagamshela iCom malunga ne-1 s ukuya +UB. | |||
| Linda malunga ne-10s. | ||||
| Indlela yokusebenza eqhelekileyo | ||||
Ezinye iisetingi
|
Tshintsha Ukufundisa-ngaphakathi + sync |
Phinda umisele useto lwasefektri | |||
| Cima unikezelo lombane. | Cima unikezelo lombane. | |||
| Qhagamshela iCom kwi-UB. | Qhagamshela iCom kwi-UB. | |||
| Vula unikezelo lombane. | Vula unikezelo lombane. | |||
| Gcina iCom iqhagamshelwe kuyo
-UB malunga ne-3 s, de zombini ii-LED zidanyaze ngaxeshanye. |
Gcina iCom iqhagamshelwe kuyo
-UB malunga ne-13 s, kude kube zombini ii-LED Yeka idanyaza. |
|||
| I-LED eluhlaza: I-LED etyheli: | idanyaza | |||
| on: Fundisa ngaphakathi | Nqamula iCom kwi-UB. | |||
| off: Ngqamanisa | ||||
| Ukutshintsha imo yokusebenza qhagamshela iCom malunga ne-1s ukuya ku-UB. | ||||
| Linda malunga ne-10s. | ||||
| Indlela yokusebenza eqhelekileyo | ||||
Idatha yobugcisa
microsonic GmbH / Phoenixseestraße 7 / 44263 Dortmund / eJamani / T +49 231 975151-0 / F +49 231 975151-51 / E info@microsonic.de / W microsonic.de
Umxholo wolu xwebhu uxhomekeke kwiinguqu zobugcisa. Iinkcukacha kolu xwebhu zinikezelwe ngendlela echazayo kuphela. Abagunyazisi naziphi na iimpawu zemveliso.
Amaxwebhu / Izibonelelo
 |
i-microsonic pico+15-TF-I Inzwa ye-Ultrasonic enePhumo elinye le-Analogue [pdf] Incwadi yokusebenzisa i-pico 15-TF-I i-Ultrasonic Sensor ene-One Analogue Output, i-pico 15-TF-I, i-Ultrasonic Sensor ene-Analogue Output enye, i-Analogue Output enye, i-Analogue Output |
