EPH R27 V2 2 Zone Programmer

Ulwazi lweMveliso

Iinkcukacha

• Ukunikezelwa kwamandla: 230VAC
• Ubushushu be-Ambient: Cima ngokuzenzekela
• Imilinganiselo: iBritish System Standard 2

FAQ

• Ndingenza ntoni ukuba umdwelisi wam wenkqubo akasebenzi kakuhle?
  • Ukuba umdwelisi wakho wenkqubo akasebenzi ngokuchanekileyo, qala ujonge ubonelelo lwamandla kunye nemidibaniso. Ukuba umcimbi uyaqhubeka, qhagamshelana negcisa eliqeqeshiweyo ukuze ufumane uncedo.

Imimiselo eMiselweyo yasefektri kunye neNgcaciso

Imimiselo eMiselweyo yeFactory

• Abafowunelwa: 230VAC
• Inkqubo: 5/2D
• Isibane sangasemva: On
• Isitshixo sephedi yezitshixo: Cimile
• Ukhuseleko kwiNqaba: Cimile
• Imo yokusebenza: Ngokuzenzekelayo
• Isitshixo sePin: Cimile
• Isithuba seNkonzo: Cimile
• Isihloko soMmandla: AMANZI ashushu ashushu

Iinkcukacha

• Ukunikezwa Amandla: 230VAC
• Ubushushu obugciniwe: 0 … 50°C
• Imilinganiselo: 161 x 100 x 31 mm
• Umlinganiselo woQhagamshelwano: 3(1)A
• Inkumbulo yeNkqubo: iminyaka eyi-5
• Uluvo lobushushu: I-NTC 100K
• Isibane sangasemva: Mhlophe
• IP Ukalo: IP20
• Ibhetri: 3VDC Lithium
  • LIR2032 & CR2032
• Ipleyiti yangasemva: Umgangatho weNkqubo yaseBritani
• Isidanga songcoliseko: 2 (Ukuchasana nomqulutage surge 2000V; ngokwe EN60730)
• Udidi lweSoftware: Iklasi A

Ingcaciso yeMveliso

Umboniso weLCD

1. Ibonisa ixesha langoku.
2. Ibonisa usuku lwangoku lweveki.
3. Ibonisa xa ukhuseleko lweqabaka luvuliwe.
4. Ibonisa xa iphedi yamaqhosha itshixiwe.
5. Ibonisa umhla wangoku.
6. Ibonisa isihloko sezowuni.
7. Ibonisa imo yangoku.

Inkcazelo yeqhosha

Umzobo wocingo

Uqhagamshelo lwetheminali

• Umhlaba
• N Ngaphakathi
• L Phila
• 1 UMmandla 1 OFF – N/C Uqhagamshelo oluqhelekileyo luvaliwe
• 2 UMmandla 2 OFF – N/C Uqhagamshelo oluqhelekileyo luvaliwe
• 3 UMmandla woku-1 IVULIWE – Akukho/O Uqhagamshelo oluqhelekileyo luvula
• 4 UMmandla woku-2 IVULIWE – Akukho/O Uqhagamshelo oluqhelekileyo luvula

Ukunyuswa kunye noFakelo

Isilumkiso!

• Ukufakela kunye nokudibanisa kufuneka kuqhutywe kuphela ngumntu oqeqeshiweyo.
• Ngabasebenzi bombane abaqeqeshiweyo kuphela okanye abasebenzi benkonzo abagunyazisiweyo abavumelekileyo ukuvula umdwelisi wenkqubo.
• Ukuba umdwelisi usetyenziswa ngendlela engachazwanga ngumenzi, ukhuseleko lwayo lunokonakala.
• Ngaphambi kokuseta umdwelisi wenkqubo, kuyimfuneko ukugqiba zonke izicwangciso ezifunekayo ezichazwe kweli candelo.
• Phambi kokuba uqalise ukufakela, umdwelisi wenkqubo kufuneka aqale aqhawuke aqhagamshelwe kwii-mains.

Lo mdwelisi wenkqubo unokunyuswa okanye axhonywe kwibhokisi ye-conduit ehlaziyiweyo.

1. Susa umdwelisi wenkqubo kwipakethe yakhe.
2. Khetha indawo yokunyusela yomdwelisi:
   • Nyusa umdwelisi weprogram ngeemitha ezi-1.5 ngaphezu komgangatho womgangatho.
   • Thintela ukuba sesichengeni selanga okanye ezinye iindawo zokufudumeza / zokupholisa.
3. Sebenzisa i-philips screwdriver ukukhulula izikrufu ze-backplate ezantsi komdwelisi weprogram.
   • Umdwelisi weprogram uphakanyiswa phezulu ukusuka ezantsi kwaye ususwe kwi-backplate. (Jonga umzobo)
4. Krwela i-backplate kwibhokisi ye-conduit ehlaziyiweyo okanye ngqo phezulu.
5. Faka iingcingo kwi-backplate ngokomzobo wocingo.
6. Hlala umdwelisi kwi-backplate uqinisekisa ukuba izikhonkwane zomdwelisi kunye nabafowunelwa be-backplate benza uqhagamshelwano lwesandi, tyhala umdwelisi wenkqubo agungxule phezulu kwaye uqinise izikrufu ze-backplate ukusuka ezantsi. (Jonga kwiSazobe 6)

Intshayelelo eKhawulezayo

Intshayelelo ekhawulezayo kumdwelisi wenkqubo wakho we-R27V2:

• Umdwelisi wenkqubo we-R27V2 uya kusetyenziswa ukulawula iizowuni ezimbini ezahlukeneyo kwisixokelelwano sakho sokufudumeza esembindini.
• Indawo nganye inokusebenza ngokuzimeleyo kwaye icwangciswe ukuba ihambelane neemfuno zakho. Indawo nganye ineenkqubo zokufudumeza ezintathu zemihla ngemihla ezibizwa ngokuba yiP1, P2 kunye neP3. Ukufumana imiyalelo malunga nendlela yokulungelelanisa useto lwenkqubo.
• Kwisikrini se-LCD somdwelisi wakho uza kubona amacandelo amabini ahlukeneyo, elinye limele indawo nganye.
• Ngaphakathi kwala macandelo unokubona ukuba yeyiphi indlela indawo ekuyo ngoku.
• Xa ikwimo ye-AUTO, iya kubonisa xa indawo icwangciswe ngokulandelayo ukuba ivulwe okanye iValiwe.
• Malunga 'noKhetho lweMode' nceda ujonge kwiphepha le-11 ngengcaciso eyongezelelekileyo.
• Xa indawo ivuliwe, uya kubona i-LED ebomvu yaloo ndawo ikhanyisa. Oku kubonisa ukuba amandla athunyelwa ukusuka kumdwelisi wenkqubo kulo mmandla.

Iindlela

Ukukhetha Indlela NGOKUZENZAKALELAYO

Kukho iindlela ezine ezikhoyo zokukhetha.

• NGOKUZENZAKALELAYO Lo mmandla usebenza ukuya kuthi ga kumaxesha amathathu 'KUVILE/KUVALE' ngosuku (P1,P2,P3).
• IMIHLA YONKE Lo mmandla usebenza ixesha elinye 'UKUVULA/UKUVALA' ngosuku. Oku kusebenza ukusuka kwixesha lokuqala elithi 'ON' ukuya kwixesha lesithathu elithi 'OFF'.
• ON Indawo ivuliwe ngokusisigxina.
• CIMILE Indawo IVIMA ngokusisigxina.
• Cofa u-Khetha ukuze utshintshe phakathi kwe-AUTO, IMIHLA YONKE, IVILE & IVILE.
• Indlela yangoku iya kuboniswa kwikhusi phantsi kwendawo ethile.
• I Khetha zifumaneka phantsi kweqweqwe langaphambili. Indawo nganye inoKhetho yayo.

Iindlela zokucwangcisa

Lo mdwelisi wenkqubo uneendlela zokucwangcisa zilandelayo.

• 5/2 Imodi yosuku Ukucwangcisa ngoMvulo ukuya kuLwesihlanu njengebhloko enye kunye noMgqibelo nangeCawa njengebhloko yesi-2.
• 7 Imowudi yosuku Ukucwangcisa zonke iintsuku ezisi-7 ngabanye.
• Imo yeeyure ezingama-24 Ukucwangcisa zonke iintsuku ezisi-7 njengebhloko enye.

Imiyalelo yokusebenza

Izicwangciso zeNkqubo yeFactory 5/2d

Lungisa iNkqubo yeNkqubo kwiMowudi yoSuku lwe-5/2

• Cofa PROG.
• Ukucwangcisa ngoMvulo ukuya kuLwesihlanu kuMmandla woku-1 kukhethiwe ngoku.
  Ukutshintsha inkqubo yeZowuni 2, cofa i Khetha ngokufanelekileyo.
  • Cofa + kwaye – ukulungisa i-P1 NGEXESHA. / Cofa u-Kulungile.
  • Cofa + kwaye – ukulungisa ixesha le-P1 OFF. / Cofa u-Kulungile.
  • Phinda le nkqubo ukulungelelanisa amaxesha e-P2 kunye ne-P3.
• Ngoku kukhethwe ucwangciso lwangoMgqibelo ukuya ngeCawa.
  • Cofa + kwaye – ukulungisa i-P1 NGEXESHA. / Cofa u-Kulungile.
  • Cofa + kwaye – ukulungisa ixesha le-P1 OFF. / Cofa u-Kulungile.
  • Phinda le nkqubo ukulungelelanisa amaxesha e-P2 kunye ne-P3.
• Cofa MENU ukubuyela kumsebenzi oqhelekileyo.
• Ngelixa ukwimo yenkqubo, ukucofa Khetha kuyakutsibela kusuku olulandelayo (ibhloko yeentsuku) ngaphandle kokutshintsha inkqubo.

Phawula:

1. Ukutshintsha ukusuka ku-5/2d ukuya kwi-7D okanye 24H inkqubo, jonga kwiphepha le-16, Imenyu P01.
2. Ukuba awunqweneli ukusebenzisa enye okanye ngaphezulu kweenkqubo zemihla ngemihla vele usete ixesha lokuqala kunye nexesha lokuphela lifane. Umzekeloampkwaye, ukuba iP2 imiselwe ukuqalisa ngo 12:00 kwaye iphele ngo 12:00 umdwelisi wenkqubo uzakuyihoya ngokulula le nkqubo kwaye aqhubele phambili kwixesha lokutshintsha elilandelayo.

Reviewkwi Useto lweNkqubo

• Cofa PROG .
• Cofa u-Kulungile ukuskrola kumaxesha osuku ngalunye (ibhloko yeentsuku).
• Cofa Khetha ukutsibela kusuku olulandelayo (ibhloko yeentsuku).
• Cofa MENU ukubuyela kumsebenzi oqhelekileyo.
• Kufuneka ucinezele i-Khetha ethile ukuze uphindeview ishedyuli yaloo zowuni.

Khuthaza umsebenzi

• Indawo nganye inokunyuselwa imizuzu engama-30, 1, 2 okanye 3 iiyure ngelixa indawo ikwi-AUTO, LONKE USUKU & OFF mode.
• Cinezela uBoost 1, 2, 3 okanye 4 amaxesha, ukusebenzisa ixesha elifunekayo le-BOOST kwiZowuni.
• Xa i-Boost icinezelwe kukho ukulibaziseka kwemizuzwana emi-5 phambi kokuba isebenze apho i-'BOOST' iya kudanyaza kwiscreen, oku kunika umsebenzisi ixesha lokukhetha ixesha elifunekayo le-BOOST.
• Ukurhoxisa i-BOOST, cinezela i-Boost efanelekileyo kwakhona.
• Xa ixesha le-BOOST liphelile okanye licinyiwe, uMmandla uya kubuyela kwimodi eyayisebenza ngaphambili ngaphambi kwe-BOOST.

Phawula

• I-BOOST ayinakusetyenziswa ngelixa i-ON okanye iMowudi yeHolide.

Umsebenzi oPhambili

• Xa indawo ikwimo ye-AUTO okanye ALLDAY, umsebenzi we-Advance uvumela umsebenzisi ukuzisa indawo okanye iizowuni phambili kwixesha elizayo lokutshintsha.
• Ukuba indawo ngoku imiselwe ukuba IVIMA kwaye i-ADV icinezelwe, indawo iya kuvulwa kude kube sekupheleni kwexesha elilandelayo lokutshintsha. Ukuba indawo ngoku imiselwe ukuba i-ON kwaye i-ADV icinezelwe, indawo iya kucinywa kude kube sekuqaleni kwexesha elilandelayo lokutshintsha.
• Cofa ADV.
• Zone1 kunye neZone 2 ziyakuqala ukudanyaza.
• Cinezela i Khetha ngokufanelekileyo.
• Indawo iya kubonisa 'ADVANCE ON' okanye 'ADVANCE OFF' kude kube sekupheleni kwexesha elilandelayo lokutshintsha.
• Indawo yoku-1 iya kuyeka ukudanyaza kwaye ingenise imo ye-Advance.
• Indawo yesi-2 iya kuhlala idanyaza.
• Phinda le nkqubo ngeZone 2 ukuba iyafuneka.
• Cofa u-Kulungile.
• Ukurhoxisa i-ADVANCE, cofa okufanelekileyo Khetha .
• Xa ixesha le-ADVANCE liphelile okanye lirhoxisiwe, indawo iya kubuyela kwindlela ebisebenza ngaphambili ngaphambi kwe-ADVANCE.

Imenyu

• Le menyu ivumela umsebenzisi ukuba ahlengahlengise imisebenzi eyongezelelweyo.
• Ukufikelela kwimenyu, cofa u-MENU.

P01 Ukuseta Umhla, Ixesha kunye neMowudi yeNkqubo DST ON

• Cofa u-MENU, 'P01 tInE' iya kuvela kwisikrini.
• Cofa u-Kulungile, unyaka uya kuqalisa ukudanyaza.
• Cofa + kwaye - ukulungisa unyaka. / Cofa u-Kulungile.
• Cofa + kwaye – ukulungisa inyanga. / Cofa u-Kulungile.
• Cofa + kwaye - ukulungisa usuku. / Cofa u-Kulungile.
• Cofa + kwaye – ukulungisa iyure. / Cofa u-Kulungile.
• Cofa + kwaye – ukulungisa umzuzu. / Cofa u-Kulungile.
• Cofa + kwaye – ukulungisa ukusuka kwi-5/2d ukuya kwi-7d okanye imo ye-24h. / Cofa u-Kulungile.
• Cofa + kwaye – ukuvula iDST (ixesha lokuKhanya ngoSuku) Vula okanye Valiwe.
• Cinezela u-MENU kwaye umdwelisi wenkqubo uya kubuyela ekusebenzeni okuqhelekileyo.

Phawula:

• Nceda ubone iinkcazo zeNkqubo yeNkqubo.

Imodi yeHolide ye-P02

• Le menyu ivumela umsebenzisi ukuba acime inkqubo yakhe yokufudumeza ngokuchaza umhla wokuqala nowokuphela.
• Cofa MENU , 'P01' iya kuvela kwisikrini.
• Cinezela de kuvele 'P02 HOL' esikrinini.
• Cofa KULUNGILE , 'IHOLIDAY FROM', umhla kunye nexesha ziya kuvela kwisikrini. Unyaka uya kuqala ukudanyaza.
• Cofa + kwaye - ukulungisa unyaka. / Cofa u-Kulungile.
• Cofa + kwaye – ukulungisa inyanga. / Cofa u-Kulungile.
• Cofa + kwaye - ukulungisa usuku. / Cofa u-Kulungile.
• Cofa + kwaye – ukulungisa iyure. / Cofa u-Kulungile.

'IHOLIDAY TO' kunye nomhla kunye nexesha ziya kuvela kwiscreen. Unyaka uya kuqala ukudanyaza.

• Cofa + kwaye - ukulungisa unyaka. / Cofa u-Kulungile .
• Cofa + kwaye – ukulungisa inyanga. / Cofa u-Kulungile .
• Cofa + kwaye – ukulungisa usuku. / Cofa u-Kulungile .
• Cofa + kwaye – ukulungisa iyure. / Cofa u-Kulungile .

Umdwelisi wenkqubo uza kucinywa ngoku ngeli xesha likhethiweyo.

• Ukurhoxisa iHOLIDAY, cofa u-Kulungile.
• Umdwelisi weprogram uya kubuyela kumsebenzi wesiqhelo xa iholide iphelile okanye irhoxisiwe.

P03 uKhuseleko lweNqaba CIMA

Le menyu ivumela umsebenzisi ukuba avule ukhuseleko lweqabaka phakathi koluhlu lwe-5°C kunye ne-20°C.

• Ukhuseleko lomkhenkce lusetelwe ukuba VALIWE.
• Cofa MENU , 'P01' iya kuvela kwisikrini.
• Cinezela + de kuvele u-'P03 FrOST' esikrinini.
• Cofa u-Kulungile , 'OFF' iya kuvela kwisikrini.
• Cofa + ukukhetha u-'ON'. / Cofa u-Kulungile .
• '5°C' iya kudanyaza kwiscreen.
• Cofa + kwaye – ukukhetha ubushushu obufunayo bokukhusela iqabaka. / Cofa u-Kulungile .
• Cinezela u-MENU kwaye umdwelisi wenkqubo uya kubuyela ekusebenzeni okuqhelekileyo.

Isimboli yeFrost iyakubonisa kwikhusi ukuba umsebenzisi uyenza isebenze kwimenyu.

Isihloko soMmandla we-P04

Le menyu ivumela umsebenzisi ukuba akhethe izihloko ezahlukeneyo zowuni ngamnye.
Iinketho zezi:

IINKETHO EZISILILEYO / UKE UTSHINTSHE KHONA

AMANZI ASHUSHU	UMMANDLA 1
UKUSHISA	UMMANDLA 2

• Cofa MENU , 'P01' iya kuvela kwisikrini.
• Cinezela + de kuvele u-'P04' esikrinini.
• Cofa u-Kulungile , 'AMANZI ashushu' aya kudanyaza kwiscreen.
• Cofa + ukutshintsha ukusuka ku-'AMANZI atshisayo' ukuya ku-'ZONE 1'. Cofa u-Kulungile . 'UKUSHISA' kuya kudanyaza kwiscreen.
• Cofa + ukutshintsha ukusuka ku-'HEATING' ukuya ku-'ZONE 2'.
• Cinezela u-MENU kwaye umdwelisi wenkqubo uya kubuyela ekusebenzeni okuqhelekileyo.

I-PIN ye-P05

• Le menyu ivumela umsebenzisi ukuba abeke iPIN yokutshixa kumdwelisi wenkqubo.
• I-PIN yokutshixa iyakunciphisa ukusebenza komdwelisi wenkqubo.

Seta i-PIN

• Cofa MENU , 'P01' iya kuvela kwisikrini.
• Cinezela + de kuvele i-'P05 PIN' kwiscreen.
• Cofa u-Kulungile , 'OFF' iya kuvela kwisikrini.
• Cofa + ukutshintsha ukusuka OFF ukuya ON. Cofa u-Kulungile . '0000' iya kudanyaza kwiscreen.
• Cofa + kwaye – ukuseta ixabiso ukusuka ku-0 ukuya ku-9 kwidijithi yokuqala. Cofa u-Kulungile ukuya kwi-PIN elandelayo.
• Xa idijithi yokugqibela ye-PIN isetiwe, cofa Lungile . Ukuqinisekisa kuboniswe ngo-'0000'.
• Cofa + kwaye – ukuseta ixabiso ukusuka ku-0 ukuya ku-9 kwidijithi yokuqala. Cofa u-Kulungile ukuya kwi-PIN elandelayo.
• Xa idijithi yokugqibela ye-PIN isetiwe, cofa Lungile. I-PIN iqinisekisiwe ngoku, kunye ne-PIN yokutshixa ivuliwe.
• Ukuba i-PIN yokuqinisekisa ifakwe ngokungachanekanga umsebenzisi ubuyiselwa kwimenyu.
• Xa iPIN yokutshixa iyasebenza uphawu lokutshixa izakudanyaza nganye yesibini kwiscreen.
• Xa umdwelisi we-PIN itshixiwe, ukucofa imenyu kuya kuthatha umsebenzisi kwiPIN yokuvula isikrini.

Phawula:

• Xa i-PIN yokutshixa yenziwe yasebenza, amaxesha e-BOOST ancitshiswa ukuya kwimizuzu engama-30 kunye namaxesha eyure e-1.
• Xa i-PIN yokutshixa yenziwe yasebenza, IiNdlela zokuKhetha ziyancitshiswa ukuya ku-Auto kunye ne-VALIWE.

Ukuvula i-PIN

• Cofa u-MENU , 'UKUVULA' kuya kuvela kwisikrini. '0000' iya kudanyaza kwiscreen.
• Cofa + kwaye – ukuseta ixabiso ukusuka ku-0 ukuya ku-9 kwidijithi yokuqala.
• Cofa u-Kulungile ukuya kwi-PIN elandelayo.
• Xa idijithi yokugqibela yePIN iseti. / Cofa u-Kulungile.
• I-PIN ngoku ivuliwe.
• Ukuba i-PIN ivuliwe kumdwelisi wenkqubo, iya kuphinda isebenze ngokuzenzekelayo ukuba akukho qhosha licinezelweyo imizuzu emi-2.

Ukuyekisa i-PIN

Xa i-PIN ivuliwe (jonga imiyalelo engentla)

• Cofa MENU , 'P01' iya kuvela kwisikrini.
• Cinezela + de kuvele i-'P05 PIN' kwiscreen.
• Cofa u-Kulungile, 'ON' iya kuvela kwisikrini.
• Cofa + okanye – ukukhetha u-'OFF'. / Cofa u-Kulungile .
• '0000' iya kudanyaza kwiscreen. Faka i-PIN. / Cofa u-Kulungile.
• I-PIN ivaliwe ngoku.
• Cinezela u-MENU ukubuyela kumsebenzi wesiqhelo okanye iza kuphuma ngokuzenzekelayo emva kwemizuzwana engama-20.

Khuphela umsebenzi

• Kopisha umsebenzi unokusetyenziswa kuphela xa imo ye-7d ikhethiwe. (Jonga iphepha 16 ukukhetha indlela ye-7d)
• Cofa i-PROG ukucwangcisa amaxesha o-ON kunye no-OFF osuku lweveki ofuna ukuyikopa.
• Sukucinezela u-Kulungile ngexesha le-P3 OFF, shiya eli xesha lidanyazayo.
• Cofa ADV , 'COPY' iya kuvela kwiscreen, kunye nosuku olulandelayo lweveki oludanyazayo.
• Ukongeza ishedyuli efunekayo kule mini cofa +.
• Ukutsiba olu suku cinezela -.
• Cofa u-Kulungile xa ishedyuli isetyenzisiwe kwiintsuku ezinqwenelekayo.
• Qinisekisa ukuba indawo ikwimowudi ye-Auto ukuze le shedyuli isebenze ngokufanelekileyo.
• Phinda le nkqubo kwiZone 2 ukuba iyafuneka.

Phawula:

• Awukwazi ukukopa iishedyuli ukusuka kwindawo enye ukuya kwenye, umz. Ukukopa ishedyuli yeZone 1 ukuya kuZone 2 akunakwenzeka.

Ukukhetha Imo Yokukhanya Ngasemva ON

Kukho iisetingi ze-backlight ezi-3 ezikhoyo ukuze ukhethe:

• NGOKUZENZAKALELAYO Isibane sangasemva sihlala sivuliwe imizuzwana eyi-10 xa naliphi na iqhosha licofa.
• ON Isibane sangasemva sivuliwe ngokusisigxina.
• CIMA Isibane sangasemva cima ngokusisigxina.

Ukulungelelanisa i-backlight cofa kwaye ubambe u-Kulungile imizuzwana eyi-10.
'Auto' ivela kwisikrini.
Cofa + okanye – ukutshintsha imo phakathi kwe-Auto, Vula kunye neValiwe.
Cofa u-Kulungile ukuqinisekisa okukhethiweyo kunye nokubuyela ekusebenzeni okuqhelekileyo.

Ukutshixa iphedi yezitshixo

• Ukutshixa umdwelisi, cofa kwaye ubambe kwaye kunye imizuzwana eli-10.
  • iya kuvela kwiscreen. Amaqhosha ngoku avaliwe.
• Ukuvula umdwelisi wenkqubo, cofa kwaye ubambe kwaye imizuzwana eyi-10.
  • izakunyamalala kwikhusi. Amaqhosha avuliwe ngoku.

Ukuseta kwakhona uMlungisi

Ukuseta ngokutsha umdwelisi wenkqubo kwizicwangciso zasefektri:

• Cofa MENU .
• 'P01' iya kuvela kwiscreen.
• Cinezela + de kuvele u-'P06 reSET' esikrinini.
• Cinezela Kulungile ukukhetha.
• 'nO' izakuqala ukudanyaza.
• Cofa +, ukutshintsha ukusuka ku-'nO' ukuya ku-'YES'.
• Cofa u-Kulungile ukuze uqinisekise.
• Umdwelisi wenkqubo uyakuqala kwakhona kwaye abuyele kwisetingi ezichaziweyo zasefektri.
• Ixesha kunye nomhla aziyi kuphinda zisetwe.

Ukuseta kwakhona okuPhambili

• Ukuseta kwakhona umdwelisi wenkqubo kwizicwangciso zasefektri, fumana iqhosha lokuseta kwakhona eliphambili kwicala lasekunene phantsi komdwelisi wenkqubo.
• Cinezela i Ukuseta Umphathi iqhosha kwaye uyikhulule.
• Isikrini siya kuhamba singenanto kwaye siqalise kwakhona.
• Umdwelisi wenkqubo uyakuqala kwakhona kwaye abuyele kwisetingi ezichaziweyo zasefektri.

Isithuba seNkonzo CIMA

• Ithuba lenkonzo linika umfaki-nkqubo amandla okubeka isibali-xesha sokubala sonyaka kumdwelisi.
• Xa iThuba leNkonzo livuliwe 'IiNkonzo' iya kuvela kwisikrini esiya kuthi sazise umsebenzisi ukuba inkonzo yabo yebhoyila yonyaka iyafuneka.

Ukufumana iinkcukacha malunga nendlela yokwenza okanye ukuvala isithuba seNkonzo, nceda uqhagamshelane nenkonzo yabathengi.

Abafowunelwa

I-EPH ilawula i-IE

• technical@ephcontrols.com
• www.ephcontrols.com/contact-us
• +353 21 471 8440
• Isikhokho, T12 W665

I-EPH ilawula i-UK

• technical@ephcontrols.co.uk
• www.ephcontrols.co.uk/contact-us
• +44 1933 322 072
• Harrow, HA1 1BD

©2024 EPH Controls Ltd.

Amaxwebhu / Izibonelelo

EPH R27 V2 2 Zone Programmer [pdf] Incwadi Yomyalelo R27 V2 2 Zone Programmer, R27 V2, 2 Zone Programmer, Zone Programmer, Programmer

Iimbekiselo

• Incwadi yokusebenzisa