Abubuwan da ke ciki boye
1 EPH R27 V2 2 Mai Shirye-shiryen Shiyya
2 Bayanin samfur
3 Saitunan Tsoffin Masana'antu Da Ƙididdiga
4 Bayanin Samfura
5 Tsarin Waya
6 Hawa & Shigarwa
7 Gabatarwa Mai Sauri
8 Hanyoyi
9 Umarnin Aiki
9.1 Ayyukan Ci gaba
10 Menu
10.1 Sake saitin Programmer
11 Lambobin sadarwa
12 Takardu / Albarkatu
12.1 Magana
13 Labarai masu alaka

EPH-logo

EPH R27 V2 2 Mai Shirye-shiryen Shiyya

EPH-R27-V2-2-Zone-Programmer-samfurin

Bayanin samfur

Ƙayyadaddun bayanai

  • Samar da wutar lantarki: 230VAC
  • Zazzabi na yanayi: A kashe atomatik
  • Girma: Tsarin Tsarin Biritaniya 2

FAQ

  • Menene zan yi idan mai tsara shirye-shirye na baya aiki yadda ya kamata?
    • Idan mai tsara shirye-shiryen ku baya aiki daidai, da farko duba wutar lantarki da haɗin kai. Idan batun ya ci gaba, tuntuɓi ƙwararren masani don taimako.

Saitunan Tsoffin Masana'antu Da Ƙididdiga

Saitunan Tsoffin Masana'antuEPH-R27-V2-2-Zone-Programmer-fig-1

  • Lambobi: 230VAC
  • Shirin: 5/2D
  • Hasken Baya: On
  • Kulle faifan maɓalli: Kashe
  • Kariyar sanyi: Kashe
  • Yanayin Aiki: Mota
  • Kulle Pin: Kashe
  • Tazarar Sabis: Kashe
  • Taken yanki: RUWAN ZAFI

Ƙayyadaddun bayanai

  • Tushen wutan lantarki: 230VAC
  • Yanayin yanayi: 0 ... 50 ° C
  • Girma: 161 x 100 x 31 mm
  • Ƙimar Tuntuɓi: 3 (1) A
  • Ƙwaƙwalwar Shirin: Shekaru 5
  • Sensor Zazzabi: NTC 100K
  • Hasken Baya: Fari
  • Matsayin IP: IP20
  • Baturi: 3VDC lithium
    • LIR2032 & CR2032
  • Farantin baya: Tsarin Tsarin Biritaniya
  • Matsayin gurɓatawa: 2 (Juriya ga voltagkarfin 2000V; EN 60730
  • Ajin Software: Darasi A

Bayanin Samfura

Nuni LCD

EPH-R27-V2-2-Zone-Programmer-fig-2

  1. Nuna lokacin yanzu.
  2. Yana nuna ranar mako na yanzu.
  3. Nunawa lokacin da aka kunna kariyar sanyi.
  4. Nunawa lokacin da faifan maɓalli ke kulle.
  5. Nuna kwanan wata.
  6. Nuna taken yanki.
  7. Yana nuna yanayin yanzu.

Bayanin Maɓalli

EPH-R27-V2-2-Zone-Programmer-fig-3

Tsarin Waya

EPH-R27-V2-2-Zone-Programmer-fig-4

Haɗin Tasha

  • EPH-R27-V2-2-Zone-Programmer-fig-5Duniya
  • N tsaka tsaki
  • L Rayuwa
  • 1 Yanki 1 KASHE – N/C Haɗin da aka rufe kullum
  • 2 Yanki 2 KASHE – N/C Haɗin da aka rufe kullum
  • 3 Yanki 1 ON - N/O Haɗin buɗewa kullum
  • 4 Yanki 2 ON - N/O Haɗin buɗewa kullum

Hawa & Shigarwa

EPH-R27-V2-2-Zone-Programmer-fig-6

Tsanaki!

  • ƙwararren mutum ne kawai ya kamata ya yi shigarwa da haɗin kai.
  • ƙwararrun masu lantarki ko ma'aikatan sabis masu izini ne kawai aka ba su izinin buɗe mai tsara shirye-shirye.
  • Idan an yi amfani da mai shirye-shiryen ta hanyar da masana'anta ba ta bayyana ba, amincinsa na iya lalacewa.
  • Kafin saita mai shirye-shirye, ya zama dole don kammala duk saitunan da ake buƙata da aka bayyana a cikin wannan sashe.
  • Kafin fara shigarwa, dole ne a fara cire haɗin na'urar daga na'urar sadarwa.

Ana iya hawa wannan mai tsara shirye-shirye ko kuma a ɗaura shi zuwa akwatin da aka ajiye.

  1. Cire mai shirye-shirye daga marufi.
  2. Zaɓi wurin hawa don mai tsara shirye-shirye:
    • Dutsen mai shirye-shiryen mita 1.5 sama da matakin bene.
    • Hana kai tsaye ga hasken rana ko wasu hanyoyin dumama/ sanyaya.
  3. Yi amfani da philips screwdriver don sassauta skru na farantin baya a ƙasan mai shirin.
    • Ana ɗaga mai shirin zuwa sama daga ƙasa kuma an cire shi daga farantin baya. (Duba zane)
  4. Mayar da farantin baya a kan akwatin magudanar ruwa ko kai tsaye zuwa saman.
  5. Waya farantin baya kamar yadda aka tsara zanen wayoyi.
  6. Zama mai shirye-shiryen akan farantin baya don tabbatar da cewa masu shirye-shiryen suna yin haɗin sauti, tura mai shirye-shiryen zuwa saman sannan kuma ƙara screws na backplate daga ƙasa. (Duba zane na 6)

Gabatarwa Mai Sauri

Gabatarwa mai sauri ga mai tsara shirin R27V2:

  • Za a yi amfani da mai shirye-shiryen R27V2 don sarrafa yankuna daban-daban guda biyu a cikin tsarin dumama ku na tsakiya.
  • Kowane yanki ana iya sarrafa kansa da kuma tsara shi don dacewa da bukatunku. Kowane yanki yana da shirye-shiryen dumama har guda uku da ake kira P1, P2 da P3. Don umarnin yadda ake daidaita saitunan shirin.
  • A kan allon LCD na mai shirye-shiryen ku za ku ga sassa daban-daban guda biyu, ɗaya don wakiltar kowane yanki.
  • A cikin waɗannan sassan za ku iya ganin yanayin da yankin yake a halin yanzu.
  • Lokacin cikin yanayin AUTO, zai nuna lokacin da aka tsara yankin gaba don kunnawa ko KASHE.
  • Don 'Zabin Yanayin' don Allah duba shafi na 11 don ƙarin bayani.
  • Lokacin da yankin ya kunna, zaku ga jajayen LED don wannan yankin yana haskakawa. Wannan yana nuna cewa ana aika wutar lantarki daga masu shirye-shirye a wannan yankin.

Hanyoyi

Zaɓin Yanayin EPH-R27-V2-2-Zone-Programmer-fig-1AUTO

Akwai hanyoyi guda huɗu don zaɓi.

  • AUTO Yankin yana aiki har zuwa lokutan 'ON/KASHE' sau uku a rana (P1, P2, P3).
  • DUK RANA Yankin yana aiki da lokacin 'ON/KASHE' sau ɗaya kowace rana. Wannan yana aiki daga lokacin 'ON' na farko zuwa lokacin 'KASHE' na uku.
  • AKAN Yankin yana kunne na dindindin.
  • KASHE Yankin yana KASHE na dindindin.
  • Latsa Zaɓi don canzawa tsakanin AUTO, DUK RANA, AUNA & KASHE.
  • Za a nuna yanayin halin yanzu akan allon ƙarƙashin takamaiman yanki.
  • Ana samun Zaɓi a ƙarƙashin murfin gaba. Kowane yanki yana da nasa Zaɓi.

Hanyoyin Shirye-shirye

Wannan programmer yana da hanyoyin shirye-shirye masu zuwa.

  • Yanayin kwana 5/2 Shirye-shiryen Litinin zuwa Juma'a a matsayin shinge daya da Asabar da Lahadi a matsayin shinge na biyu.
  • Yanayin rana 7 Shirye-shiryen duk kwanaki 7 daban-daban.
  • Yanayin awa 24 Shirye-shiryen duk kwanaki 7 azaman toshe ɗaya.

Umarnin Aiki

Saitunan Shirin Masana'antu EPH-R27-V2-2-Zone-Programmer-fig-15/2d

EPH-R27-V2-2-Zone-Programmer-fig-10

Daidaita Saitin Shirin a Yanayin Rana 5/2

  • Danna PROG.
  • Yanzu an zaɓi shirye-shiryen Litinin zuwa Juma'a don Zone 1.
    Don canza shirye-shirye don Yanki 2, danna Zaɓin da ya dace.
    • Latsa + da – don daidaita lokacin P1. / Danna Ok.
    • Latsa + da – don daidaita lokacin KASHE P1. / Danna Ok.
    • Maimaita wannan tsari don daidaita lokutan P2 da P3.
  • Yanzu an zaɓi shirye-shiryen ranar Asabar zuwa Lahadi.
    • Latsa + da – don daidaita lokacin P1. / Danna Ok.
    • Latsa + da – don daidaita lokacin KASHE P1. / Danna Ok.
    • Maimaita wannan tsari don daidaita lokutan P2 da P3.
  • Danna MENU don komawa aiki na yau da kullun.
  • Yayin da yake cikin yanayin shirye-shirye, danna Zaɓi zai yi tsalle zuwa rana mai zuwa (toshewar kwanaki) ba tare da canza shirin ba.

Lura:

  1. Don canzawa daga 5/2d zuwa shirye-shiryen 7D ko 24H, koma zuwa shafi na 16, Menu P01.
  2. Idan ba kwa son amfani da ɗaya ko fiye na shirye-shiryen yau da kullun to kawai saita lokacin farawa da ƙarshen ƙarshen su zama iri ɗaya. Domin misaliampLe, idan aka saita P2 don farawa da karfe 12:00 kuma ya ƙare da ƙarfe 12:00 mai shirye-shiryen zai yi watsi da wannan shirin kawai kuma ya ci gaba zuwa lokacin sauyawa na gaba.

Reviewa cikin Saitunan Shirin

  • Danna PROG .
  • Latsa OK don gungurawa cikin lokutan rana ɗaya (toshewar kwanaki).
  • Latsa Zaɓi don tsalle zuwa rana ta gaba (toshewar kwanaki).
  • Danna MENU don komawa aiki na yau da kullun.
  • Dole ne ku danna takamaiman Zaɓi don sakeview jadawalin wannan yanki.

Ayyukan Haɓakawa

  • Ana iya haɓaka kowane yanki na tsawon mintuna 30, 1, 2 ko 3 yayin da yankin yake cikin yanayin AUTO, DUK RANA & KASHE.
  • Latsa Boost 1, 2, 3 ko 4, don amfani da lokacin BOOST da ake so zuwa Yanki.
  • Lokacin da aka danna Boost akwai jinkiri na daƙiƙa 5 kafin kunnawa inda 'BOOST' zai haskaka akan allon, wannan yana bawa mai amfani lokaci don zaɓar lokacin BOOST da ake so.
  • Don soke BOOST, sake danna Boost daban-daban.
  • Lokacin da lokacin BOOST ya ƙare ko an soke shi, Yankin zai koma yanayin da yake aiki a baya kafin BOOST.

Lura

  • Ba za a iya amfani da BOOST yayin da yake cikin ON ko Yanayin Holiday ba.
Ayyukan Ci gaba
  • Lokacin da yanki ke cikin yanayin AUTO ko ALLDAY, aikin Ci gaba yana bawa mai amfani damar kawo yankin ko shiyyoyin gaba zuwa lokacin sauyawa na gaba.
  • Idan yankin a halin yanzu yana da lokacin kashewa kuma an danna ADV, yankin za a kunna shi har zuwa ƙarshen lokacin sauyawa na gaba. Idan yankin a halin yanzu yana da lokacin kunnawa kuma an danna ADV, yankin za a kashe shi har zuwa farkon lokacin sauyawa na gaba.
  • Danna ADV.
  • Zone1 da Zone 2 za su fara walƙiya.
  • Danna Zaɓin da ya dace.
  • Yankin zai nuna 'KASHEWA' ko 'KASHE' har zuwa ƙarshen lokacin sauyawa na gaba.
  • Yanki 1 zai daina walƙiya kuma ya shiga Yanayin gaba.
  • Yanki 2 zai ci gaba da walƙiya.
  • Maimaita wannan tsari tare da Zone 2 idan an buƙata.
  • Danna Ok.
  • Don soke wani ADVANCE, danna Zaɓin da ya dace.
  • Lokacin da lokacin ADVANCE ya ƙare ko aka soke, yankin zai koma yanayin da yake aiki a baya kafin CIGABA.

Menu

  • Wannan menu yana bawa mai amfani damar daidaita ƙarin ayyuka.
  • Don samun dama ga menu, danna MENU.

P01 Saita Kwanan wata, Lokaci da Yanayin Shirye-shiryen EPH-R27-V2-2-Zone-Programmer-fig-1DST NA

  • Danna MENU, 'P01 tInE' zai bayyana akan allon.
  • Danna Ok, shekara zata fara walƙiya.
  • Latsa + da – don daidaita shekara. / Danna Ok.
  • Latsa + da – don daidaita wata. / Danna Ok.
  • Latsa + da – don daidaita ranar. / Danna Ok.
  • Latsa + da – don daidaita sa'a. / Danna Ok.
  • Latsa + da – don daidaita minti. / Danna Ok.
  • Latsa + da – don daidaitawa daga yanayin 5/2d zuwa 7d ko yanayin 24h. / Danna Ok.
  • Latsa + da – don kunna DST (Lokacin Ajiye Hasken Rana) Kunnawa ko Kashe.
  • Danna MENU kuma mai tsara shirye-shirye zai koma aiki na yau da kullun.

Lura:

  • Da fatan za a duba don kwatancen Hanyoyin Shirye-shiryen.

P02 Yanayin Hutu

  • Wannan menu yana bawa mai amfani damar kashe tsarin dumama su ta hanyar ayyana ranar farawa da ƙarshen ƙarshe.
  • Danna MENU , 'P01' zai bayyana akan allon.
  • Danna har sai 'P02 HOL' zai bayyana akan allon.
  • Danna Ok, 'HUtu DAGA', kwanan wata da lokaci zasu bayyana akan allon. Shekarar za ta fara walƙiya.
  • Latsa + da – don daidaita shekara. / Danna Ok.
  • Latsa + da – don daidaita wata. / Danna Ok.
  • Latsa + da – don daidaita ranar. / Danna Ok.
  • Latsa + da – don daidaita sa'a. / Danna Ok.

'HUTUN ZUWA' kuma kwanan wata da lokaci za su bayyana akan allon. Shekarar za ta fara walƙiya.

  • Latsa + da – don daidaita shekara. / Danna Ok .
  • Latsa + da – don daidaita wata. / Danna Ok .
  • Latsa + da – don daidaita ranar. / Danna Ok .
  • Latsa + da – don daidaita sa'a. / Danna Ok .

Yanzu za a kashe mai shirye-shirye a cikin wannan lokacin da aka zaɓa.

  • Don soke HUTU, danna Ok.
  • Mai shirye-shiryen zai dawo aiki na yau da kullun idan an gama hutu ko aka soke.

P03 Kariyar Frost EPH-R27-V2-2-Zone-Programmer-fig-1KASHE

Wannan menu yana bawa mai amfani damar kunna kariyar sanyi tsakanin kewayon 5°C da 20°C.

  • Kariyar sanyi an saita tsoho zuwa KASHE.
  • Danna MENU , 'P01' zai bayyana akan allon.
  • Danna + har sai 'P03 FrOST' ya bayyana akan allon.
  • Danna Ok, 'KASHE' zai bayyana akan allon.
  • Danna + don zaɓar 'ON'. / Danna Ok .
  • '5°C' zai haska akan allon.
  • Latsa + da – don zaɓar zafin kariyar sanyi da kuke so. / Danna Ok .
  • Danna MENU kuma mai tsara shirye-shirye zai koma aiki na yau da kullun.

Alamar Frost EPH-R27-V2-2-Zone-Programmer-fig-11zai nuna akan allon idan mai amfani ya kunna shi a cikin menu.

Taken Yankin P04

Wannan menu yana bawa mai amfani damar zaɓar lakabi daban-daban don kowane yanki.
Zaɓuɓɓukan su ne:

ZABI NA TSOKACI / SAKE SUNA ZABI

RUWAN ZAFI KASHI NA 1
DUMI-DUMINSU KASHI NA 2
  • Danna MENU , 'P01' zai bayyana akan allon.
  • Danna + har sai 'P04' ya bayyana akan allon.
  • Danna Ok, 'RUWAN ZAFI' zai haska akan allon.
  • Latsa + don canzawa daga 'RUWAN ZAFI' zuwa 'ZONE 1'. Danna Ok . 'HEATING' zai haskaka akan allon.
  • Latsa + don canzawa daga 'HEATING' zuwa 'ZONE 2'.
  • Danna MENU kuma mai tsara shirye-shirye zai koma aiki na yau da kullun.

P05 PIN

  • Wannan menu yana bawa mai amfani damar sanya makullin PIN akan mai shirin.
  • Kulle PIN zai rage ayyukan mai shirye-shirye.

Saita PIN

  • Danna MENU , 'P01' zai bayyana akan allon.
  • Latsa + har sai 'P05 PIN' ya bayyana akan allon.
  • Danna Ok, 'KASHE' zai bayyana akan allon.
  • Latsa + don canzawa daga KASHE zuwa ON. Danna Ok . '0000' zai yi walƙiya akan allon.
  • Latsa + da – don saita ƙimar daga 0 zuwa 9 don lamba ta farko. Danna Ok don matsawa zuwa lambar PIN ta gaba.
  • Lokacin da aka saita lambar ƙarshe ta PIN, danna Ok . Tabbatar yana nunawa tare da '0000'.
  • Latsa + da – don saita ƙimar daga 0 zuwa 9 don lamba ta farko. Danna Ok don matsawa zuwa lambar PIN ta gaba.
  • Lokacin da aka saita lambar ƙarshe na PIN, danna Ok. An tabbatar da PIN ɗin, kuma kulle PIN ɗin yana kunne.
  • Idan an shigar da PIN na tabbatarwa ba daidai ba ana dawo da mai amfani zuwa menu.
  • Lokacin da kulle PIN ke aiki alamar KulleEPH-R27-V2-2-Zone-Programmer-fig-7 zai haskaka kowane dakika akan allon.
  • Lokacin da mai shirin ke kulle PIN, danna menu zai kai mai amfani zuwa allon buɗe PIN.

Lura:

  • Lokacin da aka kunna kulle PIN, ana rage lokutan BOOST zuwa sa'o'i 30 da awa 1.
  • Lokacin da aka kunna kulle PIN, Zaɓuɓɓukan Yanayi ana rage su zuwa atomatik da KASHE.

Don buše PIN

  • Danna MENU , 'Buɗewa' zai bayyana akan allon. '0000' zai yi walƙiya akan allon.
  • Latsa + da – don saita ƙimar daga 0 zuwa 9 don lamba ta farko.
  • Danna Ok don matsawa zuwa lambar PIN ta gaba.
  • Lokacin da aka saita lambar ƙarshe ta PIN. / Danna Ok.
  • An buɗe PIN ɗin yanzu.
  • Idan an buɗe PIN akan mai shirye-shiryen, zai sake kunnawa ta atomatik idan babu maɓalli da aka danna tsawon mintuna 2.

Don kashe PIN ɗin

Lokacin da aka buɗe PIN (duba umarnin sama)

  • Danna MENU , 'P01' zai bayyana akan allon.
  • Latsa + har sai 'P05 PIN' ya bayyana akan allon.
  • Danna Ok, 'ON' zai bayyana akan allon.
  • Latsa + ko - don zaɓar 'KASHE'. / Danna Ok .
  • '0000' zai yi walƙiya akan allon. Shigar da PIN. / Danna Ok.
  • An kashe PIN ɗin yanzu.
  • Danna MENU don komawa aiki na yau da kullun ko kuma zai fita ta atomatik bayan daƙiƙa 20.

Kwafi Aiki

  • Ana iya amfani da aikin kwafi kawai lokacin da aka zaɓi yanayin 7d. (Duba shafi na 16 don zaɓar yanayin 7d)
  • Danna PROG don tsara lokutan ON da KASHE na ranar mako da kake son kwafi.
  • Kar a danna Ok akan lokacin P3, bar wannan lokacin yana walƙiya.
  • Danna ADV , 'COPY' zai bayyana akan allon, tare da rana mai zuwa na mako.
  • Don ƙara jadawalin da ake so zuwa yau danna +.
  • Don tsallake wannan rana latsa -.
  • Danna Ok lokacin da aka yi amfani da jadawalin zuwa kwanakin da ake so.
  • Tabbatar cewa yankin yana cikin yanayin atomatik don wannan jadawalin yayi aiki daidai da haka.
  • Maimaita wannan tsari don Zone 2 idan an buƙata.

Lura:

  • Ba za ku iya kwafin jadawalin jadawalin daga wannan shiyya zuwa wancan ba, Misali Kwafi Jadawalin Yanki 1 zuwa Yanki 2 ba zai yiwu ba.

Zaɓin Yanayin Hasken Baya EPH-R27-V2-2-Zone-Programmer-fig-1ON

Akwai saitunan hasken baya guda 3 akwai don zaɓi:

  • AUTO Hasken baya yana kunne na daƙiƙa 10 lokacin da aka danna kowane maɓalli.
  • ON Hasken baya yana Kunna har abada.
  • KASHE Hasken baya yana Kashe har abada.

Don daidaita hasken baya latsa ka riƙe Ok na daƙiƙa 10.
'Auto' yana bayyana akan allon.
Latsa + ko – don canza yanayin tsakanin atomatik, Kunnawa da Kashewa.
Danna Ok don tabbatar da zaɓi kuma don komawa aiki na yau da kullun.

Kulle faifan maɓalli

  • Don kulle mai shirye-shirye, danna ka riƙe kuma tare na tsawon daƙiƙa 10.
    • EPH-R27-V2-2-Zone-Programmer-fig-7zai bayyana akan allon. Yanzu an kashe maɓallan.
  • Don buɗe shirin, danna ka riƙe kuma na daƙiƙa 10.
    • EPH-R27-V2-2-Zone-Programmer-fig-7zai bace daga allon. Yanzu an kunna maɓallan.
Sake saitin Programmer

Don sake saita mai shirye-shirye zuwa saitunan masana'anta:

  • Latsa MENU .
  • 'P01' zai bayyana akan allon.
  • Latsa + har sai 'P06 reSEt' ya bayyana akan allon.
  • Latsa Ya yi don za .i.
  • 'no' zai fara walƙiya.
  • Latsa +, don canzawa daga 'NO' zuwa 'YES'.
  • Danna Ok don tabbatarwa.
  • Mai shirye-shiryen zai sake farawa kuma ya koma ga ma'anar ma'auni na masana'anta.
  • Ba za a sake saita lokaci da kwanan wata ba.

Sake saitin Jagora

  • Don ƙware a sake saita mai shirye-shirye zuwa saitunan masana'anta, nemo maɓallin sake saiti na mahimmin a gefen dama a ƙarƙashin mai shirye-shiryen.
  • Danna maɓallin Sake saitin Jagora kuma a sake shi.
  • Allon zai tafi babu komai kuma ya sake yi.
  • Mai shirye-shiryen zai sake farawa kuma ya koma ga ma'anar ma'auni na masana'anta.

Tazarar SabisEPH-R27-V2-2-Zone-Programmer-fig-1 KASHE

  • Tazarar sabis yana ba mai sakawa ikon sanya lokacin ƙidayar shekara-shekara akan mai shirin.
  • Lokacin da aka kunna Tazarar Sabis 'SErv' zai bayyana akan allon wanda zai faɗakar da mai amfani cewa sabis ɗin tukunyar jirgi ya ƙare.

Don cikakkun bayanai kan yadda ake kunna ko kashe Tazarar Sabis, tuntuɓi sabis na abokin ciniki.

Lambobin sadarwa

Gudanar da EPH IE

EPH-R27-V2-2-Zone-Programmer-fig-8

EPH Sarrafa Burtaniya

EPH-R27-V2-2-Zone-Programmer-fig-9

©2024 EPH Controls Ltd.

Takardu / Albarkatu

EPH R27 V2 2 Mai Shirye-shiryen Shiyya [pdf] Jagoran Jagora
R27 V2 2 Mai Shirye-shiryen Shiyya, R27 V2, Mai Shirye-shiryen Shiyya 2, Mai Shirye-shiryen Shiyya, Mai Shirye-shirye

Magana

Labarai masu alaka

Bar sharhi

Ba za a buga adireshin imel ɗin ku ba. Ana yiwa filayen da ake buƙata alama *