Zamkatimu kubisa
1 EPH R27 V2 2 Zone Programmer
2 Zambiri Zamalonda
3 Zokonda Zosakhazikika Pafakitale Ndi Mafotokozedwe
4 Mafotokozedwe Akatundu
5 Chithunzi cha Wiring
6 Kuyika & Kuyika
7 Mawu Oyamba Mwamsanga
8 Mitundu
9 Malangizo Ogwiritsira Ntchito
9.1 Ntchito Yotsogola
10 Menyu
10.1 Kukhazikitsanso Pulogalamu
11 Contacts
12 Zolemba / Zothandizira
12.1 Maumboni
13 Zolemba Zogwirizana

Chizindikiro cha EPH

EPH R27 V2 2 Zone Programmer

EPH-R27-V2-2-Zone-Programmer-product

Zambiri Zamalonda

Zofotokozera

  • Kupereka Mphamvu: 230VAC
  • Kutentha Kozungulira: Kuzimitsa Paokha
  • Makulidwe: British System Standard 2

FAQ

  • Ndiyenera kuchita chiyani ngati pulogalamu yanga siyikuyenda bwino?
    • Ngati wopanga mapulogalamu anu sakugwira ntchito moyenera, choyamba yang'anani magetsi ndi maulumikizidwe. Ngati vutoli likupitilira, funsani katswiri wodziwa kuti akuthandizeni.

Zokonda Zosakhazikika Pafakitale Ndi Mafotokozedwe

Zokonda Zofikira PafakitaleEPH-R27-V2-2-Zone-Programmer-fig-1

  • Ma Contacts: 230VAC
  • Pulogalamu: 5/2D
  • Kumbuyo: On
  • Loko keypad: Kuzimitsa
  • Chitetezo cha Frost: Kuzimitsa
  • Njira Yogwirira Ntchito: Zadzidzidzi
  • Pin Lock: Kuzimitsa
  • Nthawi Yantchito: Kuzimitsa
  • Mutu wa Zone: KUTENGA KWA MADZI OTSATIRA

Zofotokozera

  • Magetsi: 230VAC
  • Kutentha Kozungulira: 0 ... 50°C
  • Makulidwe: 161 x 100 x 31 mm
  • Makonda Anu: 3(1)A
  • Memory Pulogalamu: 5 Zaka
  • Sensor ya Kutentha: Mtengo wa NTC 100K
  • Kumbuyo: Choyera
  • Mulingo wa IP: IP20
  • Batri: 3VDC Lithiyamu
    • LIR2032 & CR2032
  • Chophimba chakumbuyo: British System Standard
  • Digiri ya kuipitsa: 2 (Kutsutsa voltagndi mphamvu 2000V; malinga ndi EN60730)
  • Pulogalamu ya Mapulogalamu: Kalasi A

Mafotokozedwe Akatundu

Chiwonetsero cha LCD

EPH-R27-V2-2-Zone-Programmer-fig-2

  1. Ikuwonetsa nthawi yapano.
  2. Imawonetsa tsiku lomwelo la sabata.
  3. Imawonetsa pamene chitetezo chachisanu chikuyatsidwa.
  4. Imawonekera pamene keypad yatsekedwa.
  5. Imawonetsa tsiku lapano.
  6. Imawonetsa mutu wa zone.
  7. Imawonetsa mawonekedwe apano.

Kufotokozera Batani

EPH-R27-V2-2-Zone-Programmer-fig-3

Chithunzi cha Wiring

EPH-R27-V2-2-Zone-Programmer-fig-4

Magulu a Terminal

  • EPH-R27-V2-2-Zone-Programmer-fig-5Dziko lapansi
  • N Wosalowerera ndale
  • L Khalani ndi moyo
  • 1 Zone 1 OFF - N/C Kulumikizana kotsekedwa nthawi zambiri
  • 2 Zone 2 OFF - N/C Kulumikizana kotsekedwa nthawi zambiri
  • 3 Zone 1 ON - N/O Nthawi zambiri kulumikizana kotseguka
  • 4 Zone 2 ON - N/O Nthawi zambiri kulumikizana kotseguka

Kuyika & Kuyika

EPH-R27-V2-2-Zone-Programmer-fig-6

Chenjezo!

  • Kuyika ndi kulumikiza kuyenera kuchitidwa ndi munthu woyenerera.
  • Amagetsi oyenerera okha kapena ogwira ntchito ovomerezeka ndi omwe amaloledwa kutsegula pulogalamuyo.
  • Ngati wopanga mapulogalamuwa agwiritsidwa ntchito m'njira yosadziwika ndi wopanga, chitetezo chake chikhoza kuwonongeka.
  • Musanakhazikitse wopanga mapulogalamu, ndikofunikira kumaliza zokonda zonse zomwe zafotokozedwa mgawoli.
  • Asanayambe kukhazikitsa, wopanga mapulogalamuyo ayenera kuchotsedwa pa mains.

Pulogalamuyi imatha kuyikidwa pamwamba kapena kuyikidwa pabokosi lokhazikika.

  1. Chotsani wopanga mapulogalamu pamapaketi ake.
  2. Sankhani malo okwera a wopanga mapulogalamu:
    • Ikani pulogalamuyo pamtunda wa 1.5 metres kuchokera pansi.
    • Pewani kukhudzana ndi dzuwa kapena zinthu zina zotenthetsera / kuzizira.
  3. Gwiritsani ntchito philips screwdriver kuti mumasule zomangira za backplate pansi pa pulogalamuyo.
    • Wopanga mapulogalamu amakwezedwa mmwamba kuchokera pansi ndikuchotsedwa kumbuyo. (Onani chithunzi)
  4. Mangani chinsalu chakumbuyo pabokosi lotsekeka kapena molunjika pamwamba.
  5. Yambani chikwangwani chakumbuyo molingana ndi chithunzi cha mawaya.
  6. Khalani wopanga mapulogalamu ku backplate ndikuwonetsetsa kuti mapini opangira mapulogalamu ndi zolumikizira zakumbuyo zikulumikizana ndi mawu, kanikizani wopanga pulogalamuyo kumtunda ndikumangitsa zomangira za backplate kuchokera pansi. (Onani chithunzi 6)

Mawu Oyamba Mwamsanga

Kuyambitsa mwachangu kwa pulogalamu yanu ya R27V2:

  • Pulogalamu ya R27V2 idzagwiritsidwa ntchito kuwongolera magawo awiri osiyana mu makina anu otentha apakati.
  • Dera lililonse litha kuyendetsedwa palokha ndikukonzedwa kuti ligwirizane ndi zosowa zanu. Chigawo chilichonse chimakhala ndi mapulogalamu atatu otenthetsera tsiku ndi tsiku otchedwa P1, P2 ndi P3. Kwa malangizo amomwe mungasinthire makonzedwe a pulogalamu.
  • Pazenera la LCD la wopanga mapulogalamu anu mudzawona magawo awiri osiyana, amodzi kuyimira gawo lililonse.
  • M'magawo awa mutha kuwona momwe zone iliri pano.
  • Ikakhala mu mawonekedwe a AUTO, iwonetsa nthawi yomwe gawolo lidzakonzedwanso kuti liziyatsidwa kapena KUZIMU.
  • Pazosankha za 'Mode Selection' chonde onani tsamba 11 kuti mumve zambiri.
  • Gawoli likakhala ON, mudzawona kuwala kofiyira kwa chigawocho. Izi zikuwonetsa kuti mphamvu ikutumizidwa kuchokera kwa wopanga mapulogalamu pagawoli.

Mitundu

Kusankha Mode EPH-R27-V2-2-Zone-Programmer-fig-1AUTO

Pali mitundu inayi yomwe ilipo posankha.

  • AUTO Malowa amagwira ntchito mpaka nthawi zitatu za 'ON/OFF' patsiku (P1,P2,P3).
  • TSIKU LONSE Derali limagwira ntchito nthawi imodzi ya 'ON/OFF' patsiku. Izi zimagwira ntchito kuyambira nthawi yoyamba ya 'ON' mpaka nthawi yachitatu ya 'WOTSITSA'.
  • ON Zone ili ON mpaka kalekale.
  • ZOYIMWA Zone ili WOZIMItsidwa mpaka kalekale.
  • Dinani Select kuti musinthe pakati pa AUTO, TSIKU LONSE, ON & OFF.
  • Njira yamakono idzawonetsedwa pazenera pansi pa zone yeniyeni.
  • The Select amapezeka pansi pachikuto chakutsogolo. Zone iliyonse ili ndi Sankhani yake.

Makonda Mapulogalamu

Wopanga mapulogalamuwa ali ndi mitundu yotsatirayi.

  • 5/2 Day mode Kupanga mapulogalamu Lolemba mpaka Lachisanu ngati chipika chimodzi ndipo Loweruka ndi Lamlungu ngati chipika chachiwiri.
  • 7 Njira yamasiku Kupanga masiku onse 7 payekha.
  • Maola 24 mode Kukonza masiku onse 7 ngati chipika chimodzi.

Malangizo Ogwiritsira Ntchito

Zokonda pa Factory Program EPH-R27-V2-2-Zone-Programmer-fig-15/2d

EPH-R27-V2-2-Zone-Programmer-fig-10

Sinthani Makhazikitsidwe a Pulogalamu mu 5/2 Day Mode

  • Dinani PROG.
  • Kukonzekera Lolemba mpaka Lachisanu ku Zone 1 kwasankhidwa.
    Kuti musinthe mapulogalamu a Zone 2, dinani koyenera Sankhani.
    • Press + ndi - kusintha P1 PA nthawi. / Dinani Chabwino.
    • Dinani + ndi - kuti musinthe nthawi ya P1 OFF. / Dinani Chabwino.
    • Bwerezani izi kuti musinthe nthawi za P2 ndi P3.
  • Mapulogalamu a Loweruka mpaka Lamlungu tsopano asankhidwa.
    • Press + ndi - kusintha P1 PA nthawi. / Dinani Chabwino.
    • Dinani + ndi - kuti musinthe nthawi ya P1 OFF. / Dinani Chabwino.
    • Bwerezani izi kuti musinthe nthawi za P2 ndi P3.
  • Dinani MENU kuti mubwerere kuntchito yanthawi zonse.
  • Mukakhala mumapulogalamu, kukanikiza Select kudzalumphira tsiku lotsatira (masiku angapo) osasintha pulogalamuyo.

Zindikirani:

  1. Kuti musinthe kuchoka pa 5/2d kupita ku 7D kapena 24H, onani patsamba 16, Menyu P01.
  2. Ngati simukufuna kugwiritsa ntchito pulogalamu imodzi kapena zingapo zatsiku ndi tsiku, ingoikani nthawi yoyambira ndi nthawi yomaliza kuti zikhale zofanana. Za example, ngati P2 yakhazikitsidwa kuti iyambe pa 12:00 ndi kutha pa 12:00 wokonza mapulogalamu amangonyalanyaza pulogalamuyi ndikupita ku nthawi yotsatira yosintha.

Reviewtsegulani Zikhazikiko za Pulogalamu

  • Dinani PROG.
  • Dinani Chabwino kuti mudutse nthawi za tsiku lililonse (masiku angapo).
  • Dinani Sankhani kuti mulumphe tsiku lotsatira (masiku angapo).
  • Dinani MENU kuti mubwerere kuntchito yanthawi zonse.
  • Muyenera kukanikiza Sankhani mwachindunji kuti mubwerensoview ndondomeko ya zone imeneyo.

Limbikitsani Ntchito

  • Chigawo chilichonse chikhoza kukulitsidwa kwa mphindi 30, 1, 2 kapena 3 maola pomwe chigawocho chili mu AUTO, ALL DAY & OFF mode.
  • Press Boost 1, 2, 3 kapena 4 nthawi, kuti mugwiritse ntchito nthawi yomwe mukufuna ya BOOST ku Zone.
  • Pamene Boost ikanikizidwa pamakhala kuchedwa kwa 5 seconds isanayambike pomwe 'BOOST' idzawunikira pazenera, izi zimapatsa wogwiritsa nthawi yosankha nthawi yomwe akufuna.
  • Kuti muletse BOOST, kanikizaninso Boost.
  • Nthawi ya BOOST ikatha kapena kuthetsedwa, Zone ibwerera kumayendedwe omwe anali akugwira ntchito isanachitike BOOST.

Zindikirani

  • BOOST singagwiritsidwe ntchito mukakhala mu ON kapena Holiday Mode.
Ntchito Yotsogola
  • Malo akakhala mumayendedwe a AUTO kapena ALLDAY, ntchito ya Advance imalola wogwiritsa ntchito kubweretsa chigawo kapena madera kupita nthawi yotsatira yosintha.
  • Ngati chigawocho chili ndi nthawi yoti ZIMAYI ndipo ADV ikanikizidwa, chigawocho chidzayatsidwa mpaka kumapeto kwa nthawi yosintha. Ngati chigawocho chili ndi nthawi yoti ON ndipo ADV ikanikizidwa, chigawocho chidzazimitsidwa mpaka kuyamba kwa nthawi yosintha.
  • Dinani ADV.
  • Zone1 ndi Zone 2 ziyamba kuwunikira.
  • Dinani yoyenera Sankhani.
  • Zone iwonetsa 'ADVANCE ON' kapena 'ADVANCE OFF' mpaka kumapeto kwa nthawi yosintha.
  • Zone 1 idzasiya kung'anima ndikulowetsa Advance mode.
  • Zone 2 ikhala yowala.
  • Bwerezani izi ndi Zone 2 ngati pakufunika.
  • Dinani Chabwino.
  • Kuti muletse ADVANCE, dinani koyenera Sankhani .
  • Nthawi ya ADVANCE ikatha kapena ikasiyidwa, zoni ibwerera ku momwe zinalili kale ADVANCE isanachitike.

Menyu

  • Menyuyi imalola wogwiritsa ntchito kusintha zina.
  • Kuti mupeze menyu, dinani MENU.

P01 Kukhazikitsa Tsiku, Nthawi ndi Njira Yopangira EPH-R27-V2-2-Zone-Programmer-fig-1DST ON

  • Dinani MENU, 'P01 tInE' idzawonekera pazenera.
  • Dinani Chabwino, chaka chiyamba kuwunikira.
  • Dinani + ndi - kuti musinthe chaka. / Dinani Chabwino.
  • Dinani + ndi - kuti musinthe mweziwo. / Dinani Chabwino.
  • Dinani + ndi - kuti musinthe tsikulo. / Dinani Chabwino.
  • Dinani + ndi - kusintha ola. / Dinani Chabwino.
  • Press + ndi - kusintha miniti. / Dinani Chabwino.
  • Dinani + ndi - kusintha kuchokera ku 5/2d mpaka 7d kapena 24h mode. / Dinani Chabwino.
  • Dinani + ndi - kuti mutsegule DST (Nthawi Yopulumutsa Kuwala Kwa Tsiku) Yatsani kapena Kuyimitsa.
  • Dinani MENU ndipo wopanga mapulogalamu abwerera kuntchito yake yabwinobwino.

Zindikirani:

  • Chonde onani mafotokozedwe a Programming Modes.

P02 Holiday Mode

  • Menyuyi imalola wogwiritsa ntchito kuzimitsa makina awo otentha pofotokoza tsiku loyambira ndi lomaliza.
  • Dinani MENU , 'P01' idzawonekera pazenera.
  • Dinani mpaka 'P02 HOL' iwonekere pazenera.
  • Dinani OK , 'HOLIDAY FROM', tsiku ndi nthawi zidzawonekera pazenera. Chaka chidzayamba kung'anima.
  • Dinani + ndi - kuti musinthe chaka. / Dinani Chabwino.
  • Dinani + ndi - kuti musinthe mweziwo. / Dinani Chabwino.
  • Dinani + ndi - kuti musinthe tsikulo. / Dinani Chabwino.
  • Dinani + ndi - kusintha ola. / Dinani Chabwino.

'HOLIDAY TO' ndipo tsiku ndi nthawi zidzawonekera pazenera. Chaka chidzayamba kung'anima.

  • Dinani + ndi - kuti musinthe chaka. / Dinani Chabwino.
  • Dinani + ndi - kuti musinthe mweziwo. / Dinani Chabwino.
  • Dinani + ndi - kuti musinthe tsikulo. / Dinani Chabwino.
  • Dinani + ndi - kusintha ola. / Dinani Chabwino.

Wopanga mapulogalamu tsopano azimitsidwa panthawi yosankhidwayi.

  • Kuti muletse HOLIDAY, dinani CHABWINO.
  • Wopanga pulogalamuyo abwerera ku ntchito yake yanthawi zonse tchuthi ikatha kapena ayimitsidwa.

P03 Chitetezo cha Frost EPH-R27-V2-2-Zone-Programmer-fig-1ZIZIMA

Menyuyi imalola wogwiritsa ntchito kuyambitsa chitetezo cha chisanu pakati pa 5°C ndi 20°C.

  • Chitetezo cha chipale chofewa chimakhazikitsidwa kukhala ZIMIMI.
  • Dinani MENU , 'P01' idzawonekera pazenera.
  • Dinani + mpaka 'P03 FrOST' iwonekere pazenera.
  • Press OK , 'WOZIMA' adzaoneka pa zenera.
  • Dinani + kuti musankhe 'ON'. / Dinani Chabwino.
  • '5°C' idzawalira pazenera.
  • Dinani + ndi - kusankha kutentha komwe mukufuna kuti muteteze kuchisanu. / Dinani Chabwino.
  • Dinani MENU ndipo wopanga mapulogalamu abwerera kuntchito yake yabwinobwino.

Chizindikiro cha Frost EPH-R27-V2-2-Zone-Programmer-fig-11idzawonetsedwa pazenera ngati wogwiritsa ntchitoyo atsegula menyu.

Mbiri ya P04

Menyuyi imalola wogwiritsa ntchito kusankha maudindo osiyanasiyana pagawo lililonse.
Zosankhazo ndi:

ZOCHITA ZOSANGALATSA / NTCHITO ZAMBIRI

MADZI OTSATIRA CHIYAMBI 1
KUCHULUKA CHIYAMBI 2
  • Dinani MENU , 'P01' idzawonekera pazenera.
  • Dinani + mpaka 'P04' iwonekere pazenera.
  • Dinani OK , 'MADZI OTSATIRA' adzawalira pazenera.
  • Dinani + kuti musinthe kuchoka ku 'MADZI OTSATIRA' kukhala 'ZONE 1'. Dinani Chabwino. 'KUCHETSA' kudzawunikira pazenera.
  • Dinani + kuti musinthe kuchoka pa 'HEATING' kukhala 'ZONE 2'.
  • Dinani MENU ndipo wopanga mapulogalamu abwerera kuntchito yake yabwinobwino.

Chithunzi cha P05P

  • Menyuyi imalola wogwiritsa ntchito kuyika loko ya PIN pa wopanga mapulogalamu.
  • Kutseka kwa PIN kudzachepetsa magwiridwe antchito a wopanga mapulogalamu.

Konzani PIN

  • Dinani MENU , 'P01' idzawonekera pazenera.
  • Dinani + mpaka 'P05 PIN' iwonekere pazenera.
  • Press OK , 'WOZIMA' adzaoneka pa zenera.
  • Dinani + kuti musinthe kuchoka pa OFF kukhala ON. Dinani Chabwino. '0000' idzawonekera pazenera.
  • Dinani + ndi - kukhazikitsa mtengo kuchokera 0 mpaka 9 pa manambala oyamba. Dinani Chabwino kuti mupite ku nambala ya PIN yotsatira.
  • Nambala yomaliza ya PIN ikakhazikitsidwa, dinani Chabwino. Chitsimikizo chikuwonetsedwa ndi '0000'.
  • Dinani + ndi - kukhazikitsa mtengo kuchokera 0 mpaka 9 pa manambala oyamba. Dinani Chabwino kuti mupite ku nambala ya PIN yotsatira.
  • Nambala yomaliza ya PIN ikakhazikitsidwa, dinani Chabwino. PIN tsopano yatsimikizika, ndipo loko ya PIN yatsegulidwa.
  • Ngati PIN yotsimikizira yalowetsedwa molakwika wogwiritsa ntchito amabwezeretsedwa ku menyu.
  • Pamene PIN loko ikugwira ntchito chizindikiro ChotsekaEPH-R27-V2-2-Zone-Programmer-fig-7 idzawunikira sekondi iliyonse pazenera.
  • Pamene mapulogalamu ndi PIN zokhoma, kukanikiza menyu kudzatengera wosuta PIN Tsegulani chophimba.

Zindikirani:

  • Loki ya PIN ikayatsidwa, nthawi za BOOST zimachepetsedwa kukhala mphindi 30 ndi nthawi ya ola limodzi.
  • Loki ya PIN ikayatsidwa, Zosankha za Mode zimachepetsedwa kukhala Auto ndi WOZIMA.

Kuti mutsegule PIN

  • Dinani MENU , 'UNLOCK' idzawonekera pazenera. '0000' idzawonekera pazenera.
  • Dinani + ndi - kukhazikitsa mtengo kuchokera 0 mpaka 9 pa manambala oyamba.
  • Dinani Chabwino kuti mupite ku nambala ya PIN yotsatira.
  • Pamene nambala yomaliza ya PIN yakhazikitsidwa. / Dinani Chabwino.
  • PIN tsopano yatsegulidwa.
  • Ngati PIN yatsegulidwa pa pulogalamuyo, imangoyambitsanso ngati palibe batani lopanikizidwa kwa mphindi ziwiri.

Kuti muletse PIN

PIN ikatsegulidwa (onani malangizo pamwambapa)

  • Dinani MENU , 'P01' idzawonekera pazenera.
  • Dinani + mpaka 'P05 PIN' iwonekere pazenera.
  • Dinani Chabwino, 'ON' idzawonekera pazenera.
  • Dinani + kapena - kuti musankhe 'ZOZIMA'. / Dinani Chabwino.
  • '0000' idzawonekera pazenera. Lowetsani PIN. / Dinani Chabwino.
  • PIN tsopano ndiyoyimitsidwa.
  • Dinani MENU kuti mubwerere kuntchito yabwino kapena ingotuluka pakadutsa masekondi 20.

Koperani Ntchito

  • Copy ntchito ingagwiritsidwe ntchito pokhapokha mawonekedwe a 7d asankhidwa. (Onani tsamba 16 kuti musankhe 7d mode)
  • Dinani PROG kuti mukonze nthawi ya ON ndi OFF ya tsikulo sabata yomwe mukufuna kukopera.
  • Osakanikiza OK pa nthawi ya P3 OFF, siyani nthawiyi ikuwunikira.
  • Dinani ADV , 'COPY' idzawonekera pazenera, ndi tsiku lotsatira la sabata likuwonekera.
  • Kuti muwonjezere ndandanda yomwe mukufuna mpaka lero dinani +.
  • Kuti mudumphe tsiku lino dinani -.
  • Dinani Chabwino pamene ndondomeko yagwiritsidwa ntchito masiku omwe mukufuna.
  • Onetsetsani kuti zone ili mu Auto mode kuti ndondomekoyi igwire ntchito moyenera.
  • Bwerezani izi ku Zone 2 ngati pakufunika.

Zindikirani:

  • Simungathe kukopera ndandanda kuchokera kudera lina kupita ku lina, mwachitsanzo Kukopera ndandanda ya Zone 1 ku Zone 2 sikutheka.

Kusankha kwa Mawonekedwe a Backlight EPH-R27-V2-2-Zone-Programmer-fig-1ON

Pali makonda a 3 backlight omwe angasankhidwe:

  • AUTO Kuwala kwambuyo kumakhalabe kwa masekondi 10 batani lililonse likakanikiza.
  • ON Nyali yakumbuyo imayatsidwa mpaka kalekale.
  • ZIZIMA Kuwala kwa backlight kwazimitsidwa.

Kuti musinthe kuwala kwa backlight ndikugwirizira OK kwa masekondi 10.
'Auto' imawonekera pazenera.
Press + kapena - kusintha mawonekedwe pakati pa Auto, On ndi Off.
Dinani OK kuti mutsimikize kusankha ndikubwerera ku ntchito yabwinobwino.

Kutseka Keypad

  • Kuti mutseke pulogalamuyo, dinani ndikugwiritsitsa ndi masekondi 10.
    • EPH-R27-V2-2-Zone-Programmer-fig-7zidzawonekera pazenera. Mabatani tsopano azimitsidwa.
  • Kuti mutsegule pulogalamuyo, dinani ndikugwira ndi masekondi 10.
    • EPH-R27-V2-2-Zone-Programmer-fig-7zidzazimiririka pazenera. Mabatani tsopano ayatsidwa.
Kukhazikitsanso Pulogalamu

Kuti mukhazikitsenso pulogalamu ku zoikamo za fakitale:

  • Dinani MENU .
  • 'P01' idzawonekera pazenera.
  • Dinani + mpaka 'P06 reSEt' iwonekere pazenera.
  • Dinani OK kuti musankhe.
  • 'nO' iyamba kung'anima.
  • Dinani +, kuti musinthe kuchokera ku 'nO' kukhala 'YES'.
  • Dinani OK kuti mutsimikizire.
  • Wopanga pulogalamuyo ayambiranso ndikubwereranso ku zoikamo zomwe zidafotokozedwa ndi fakitale.
  • Nthawi ndi tsiku sizidzakhazikitsidwanso.

Master Reset

  • Kuti mukhazikitsenso pulogalamuyo ku zoikamo za fakitale, pezani batani lokhazikitsiranso kumanja kumanja pansi pa pulogalamuyo.
  • Dinani batani la Master Reset ndikumasula.
  • Chophimbacho chidzasowa ndikuyambiranso.
  • Wopanga pulogalamuyo ayambiranso ndikubwereranso ku zoikamo zomwe zidafotokozedwa ndi fakitale.

Nthawi YothandiziraEPH-R27-V2-2-Zone-Programmer-fig-1 ZIZIMA

  • Nthawi yantchito imapatsa woyikirayo mwayi woyika chowerengera chapachaka pa wopanga mapulogalamu.
  • Nthawi ya Utumiki ikatsegulidwa 'SERv' idzawonekera pazenera zomwe zidzadziwitse wogwiritsa ntchito kuti ntchito yawo yowotchera pachaka ikuyenera.

Kuti mudziwe zambiri za momwe mungayambitsire kapena kuyimitsa nthawi ya Service Interval, chonde lemberani makasitomala.

Contacts

EPH Imawongolera IE

EPH-R27-V2-2-Zone-Programmer-fig-8

EPH Amalamulira UK

EPH-R27-V2-2-Zone-Programmer-fig-9

©2024 EPH Controls Ltd.

Zolemba / Zothandizira

EPH R27 V2 2 Zone Programmer [pdf] Buku la Malangizo
R27 V2 2 Zone Programmer, R27 V2, 2 Zone Programmer, Zone Programmer, Programmer

Maumboni

Zolemba Zogwirizana

Siyani ndemanga

Imelo yanu sisindikizidwa. Minda yofunikira yalembedwa *