LS XB Series Programmable Logic Controller
Ulwazi lweMveliso
Iinkcukacha:
- C/N: 10310001095
- Imveliso: UMlawuli weNgqiqo eCwangcisiweyo
- I-XGB CPU (E)
- Iimodeli: XB(E)C-DR10/14/20/30E, XB(E)C-DN10/14/20/30E, XB(E)C-DP10/14/20/30E
Imiyalelo yokusetyenziswa kwemveliso
XG5000 uFakelo lweSoftware:
Qinisekisa ukuba unenguqulo ye-V4.01 ye-software ye-XG5000.
PMC-310S uQhagamshelwano:
Qhagamshela usebenzisa ujongano lweRS-232C.
Ukuhlohla okubonakalayo:
Nyusa i-PLC kwindawo efanelekileyo ngokulandela imilinganiselo enikiweyo (nge-mm). Qinisekisa ukungena komoya okufanelekileyo kunye nendawo yolondolozo.
Uqhagamshelo lweeNcingo:
Landela umzobo wocingo onikwe kunye ne-PLC. Qinisekisa uqhagamshelo olululo lonikezelo lwamandla, izixhobo zokufaka/imveliso, kunye nojongano lonxibelelwano.
Ukomeleza:
Sebenzisa amandla ngaphakathi komthamo ochaziweyotaguluhlu lwe. Khangela izikhombisi zamandla ezifanelekileyo kunye nokuqaliswa kwenkqubo.
Ukucwangcisa:
Sebenzisa i-software ye-XG5000 ukucwangcisa i-PLC logic ngokusekelwe kwiimfuno zakho zesicelo. Vavanya inkqubo ngocoselelo phambi kokuba isetyenziswe.
FAQ
- Loluphi uhlobo lwesoftware olucetyiswayo lwenkqubo?
Inguqulelo yesoftware ecetyiswayo yiV4.01 yesoftware yeXG5000. - Ndingaqhagamshela njani i-PMC-310S?
Qhagamshela i-PMC-310S usebenzisa ujongano lwe-RS-232C. - Ziziphi iimeko zokusingqongileyo zokusebenzisa iPLC?
Iqondo lokushisa elisebenzayo li--25 ° C ukuya ku-70 ° C, kunye noluhlu lokufuma lwe-5% ukuya kwi-95% ye-RH.
Esi sikhokelo sofakelo sibonelela ngolwazi olulula lomsebenzi wolawulo lwe-PLC. Nceda ufunde ngononophelo olu xwebhu lwedatha kunye neencwadana ngaphambi kokusebenzisa iimveliso. Ngokukodwa funda amanyathelo okhuseleko kwaye uphathe iimveliso ngokufanelekileyo.
ImiGaqo yoKhuseleko
Intsingiselo yesilumkiso kunye nombhalo wokulumkisa
- ISILUMKISO
ISILUMKISO sibonisa imeko enokuba yingozi enokuthi, ukuba ayiphetshwa, inokubangela ukufa okanye ukwenzakala okumandundu - ISILUMKO
UKULUMKISA kubonisa imeko enokuba yingozi enokuthi, ukuba ayiphetshwa, ingabangela ukwenzakala okuncinci okanye okuphakathi. Isenokusetyenziswa ukulumkisa ngokuchasene nezenzo ezingakhuselekanga - ISILUMKISO
- Musa ukuqhagamshelana neetheminali ngelixa umbane usetyenziswa.
- Khusela imveliso ekungenwe kuyo yintsimbi yangaphandle.
- Musa ukuyisebenzisa kakubi ibhetri (ukutshaja, ukuqhaqha, ukubetha, mfutshane, ukusoda)
- ISILUMKO
- Qiniseka ukuba ujonga umthamo olinganisiweyotage kunye nolungiselelo lwetheminali phambi kocingo
- Xa ufaka iintambo, qinisa isikrufu sebhloko yeterminal ngoluhlu lwetorque echaziweyo
- Musa ukufaka izinto ezinokutsha kwindawo ezingqongileyo
- Musa ukusebenzisa i-PLC kwindawo yokungcangcazela ngokuthe ngqo
- Ngaphandle kwabasebenzi benkonzo yeengcali, Musa ukuqhaqha okanye ulungise okanye uguqule imveliso
- Sebenzisa i-PLC kwimeko-bume ehlangabezana neenkcukacha ngokubanzi eziqulethwe kule datha.
- Qinisekisa ukuba umthwalo wangaphandle awudluli umlinganiselo wemodyuli yemveliso.
- Xa ulahla i-PLC kunye nebhetri, yiphathe njengenkunkuma yamashishini.
Indawo yokusebenza
Ukufakela, jonga le miqathango ingezantsi.
| Hayi | Into | Inkcazo | Umgangatho | ||||
| 1 | Ithuba elikwiNdawo. | 0 ~ 55℃ | – | ||||
| 2 | Ubushushu bokugcina. | -25 ~ 70℃ | – | ||||
| 3 | Ukufuma kwendawo | I-5 ~ 95%RH, i-non-condensing | – | ||||
| 4 | Ukugcinwa kokufuma | I-5 ~ 95%RH, i-non-condensing | – | ||||
|
5 |
Ukungcangcazela Ukuchasa |
Ukungcangcazela ngamaxesha athile | – | – | |||
| Ukuphindaphinda | Ukukhawulezisa | Ampimfundo | Amaxesha |
IEC 61131-2 |
|||
| 5≤f<8.4㎐ | – | 3.5mm | Amaxesha ali-10 kwicala ngalinye
X AND Z |
||||
| 8.4≤f≤150㎐ | 9.8㎨(1g) | – | |||||
| Ukungcangcazela okuqhubekayo | |||||||
| Ukuphindaphinda | Ukuphindaphinda | Ampimfundo | |||||
| 5≤f<8.4㎐ | – | 1.75mm | |||||
| 8.4≤f≤150㎐ | 4.9㎨(0.5g) | – | |||||
Iinkcukacha zokusebenza
Le yinkcazo yoMsebenzi we-XGB. Ukufumana iinkcukacha ezithe vetshe, jonga kwincwadi ehambelanayo.
| Into | Inkcazo | |||
| Indlela yokusebenza | Ukusebenza okuphindaphindayo, ukusebenza komjikelo osisigxina,
Ukuphazamisa ukusebenza, ukuskena rhoqo kwexesha |
|||
| Indlela yokulawula ye-I/O | Skena inkqubo yebhetshi ehambelanayo (indlela yokuhlaziya)
Indlela ethe ngqo ngomyalelo |
|||
| Isantya sokusebenza | Umyalelo osisiseko: 0.24㎲/inyathelo | |||
| Ukwandiswa slot Max | Engundoqo+Ukhetho (ukhetho 1 slot: 10/14 uhlobo point, ukhetho 2slot: 20/30 uhlobo point) |
|||
|
umsebenzi |
Ukuqaliswa | 1 | ||
| Umjikelo osisigxina | 1 | |||
| Inqaku langaphandle | Max. 8 | |||
| Isixhobo sangaphakathi | Max. 4 | |||
| Imo yokusebenza | BALEKA, YIMA | |||
| Ukuzixilonga | Ukulibaziseka kokusebenza, inkumbulo engaqhelekanga, i-I/O engaqhelekanga | |||
| Izibuko lenkqubo | RS-232C(Umlayishi) | |||
| Indlela yokugcinwa kwedatha kukusilela kwamandla | Ukuseta indawo yelatshi kwipharamitha esisiseko | |||
| Umsebenzi owakhelwe ngaphakathi | Cnet I/F umsebenzi | Iprotocol ezinikeleyo, iprotocol yeModbus
Iprothokholi echazwe ngumsebenzisi |
||
| Ikhetha enye izibuko phakathi kwe-RS-232C 1 port kunye
RS-485 1 izibuko ngeparameter |
||||
| I-Speed Speed counter | Ukusebenza | Inqanaba eli-1 : 4㎑ 4 amajelo 2-inqanaba : 2㎑ 2 amajelo | ||
|
Imo yekhawuntara |
Iimowudi ze-counter ezi-4 zixhaswa ngokusekelwe kwi-pulse input kunye ne-INC / DEC indlela
· Imowudi yokusebenza kwepulse e-1 : INC/DEC ukubala ngenkqubo · I-1 ye-pulse operation Mode : INC/DEC count by phase B pulse input · I-2 ye-pulse operation Mode : INC/DEC count by input pulse · I-2 ye-pulse operation Mode : INC/DEC count by umahluko wesigaba |
|||
| ukusebenza | Ikhawuntara ye32bit esayiniweyo | |||
| Umsebenzi | · Ukusetha kwangaphambili kwangaphakathi/kwangaphandle · I-Latch counter
· Thelekisa isiphumo · Inani lokujikeleza ngokweyunithi yexesha |
|||
| Ukubamba i-Pulse | 50㎲ 4 amanqaku | |||
| Inqaku langaphandle liphazamise | Amanqaku ama-4: 50㎲ | |||
| Isihluzi segalelo | Ikhetha phakathi kwe-1,3,5,10,20,70,100㎳ (Kwimodyuli nganye) | |||
Isoftware yenkxaso esebenzayo
Kubumbeko lwesixokelelwano, oluguqulelo lulandelayo luyimfuneko.
XG5000 Software: V4.01 okanye ngaphezulu
Izixhobo kunye neNgcaciso zeCable
Jonga i-accessory (Oda intambo ukuba iyafuneka)
PMC-310S : I-RS-232 yokudibanisa (ukukhuphela) intambo
Igama lendawo kunye nobungakanani (mm)
Le yinxalenye engaphambili ye-CPU. Bhekisela kwigama ngalinye xa uqhuba inkqubo. Ngolwazi oluthe vetshe, jonga kwincwadi yomsebenzisi.
- Ibhloko yoNxibelelwano olwakhelwe ngaphakathi
- Ibhloko yokufaka iteminali
- Ubume bokusebenza kwe-LED
- Imo yokufaka i-LED
- Imo yemveliso ye-LED
- Umnikazi webhodi yokhetho
- Ukutshintsha kwediphu yemowudi ye-O/S
- BALEKA/YIMA iswitsha yemowudi
- PADT Isidibanisi
- Ibhloko yeterminal yamandla
- Ibhlokhi yetheminali yemveliso
- Imveliso ye-24V (amandla angaphantsi)
Ubungakanani(mm)
| Imodyuli | W | D | H |
| XB(E)C-DR(N)(P)10/14E | 97 | 64 | 90 |
| XB(E)C-DR(N)(P)20/30E | 135 | 64 | 90 |
Iintambo
Iingcingo zombane
- Kwimeko apho utshintsho lwamandla lukhulu kunoluhlu olusemgangathweni, qhagamshela umthamo ongaguqukiyotage transformer
- Qhagamshela amandla anengxolo encinci phakathi kweentambo okanye phakathi komhlaba. Kwimeko yengxolo eninzi, qhagamshela isiguquli sokwahlula okanye isihluzi sengxolo.
- amandla ePLC, isixhobo se-I/O kunye nabanye oomatshini kufuneka bahlukane.
- Sebenzisa umhlaba ozinikeleyo ukuba kunokwenzeka. Kwimeko yokusebenza koMhlaba, sebenzisa umhlaba weklasi ezi-3 (ukumelana nomhlaba 100 Ω okanye ngaphantsi) kwaye Sebenzisa ngaphezu kwe-2 mm2 intambo yomhlaba. Ukuba umsebenzi ongaqhelekanga ufunyenwe ngokomhlaba, yahlula umhlaba
Iwaranti
- Ixesha lewaranti ziinyanga ezingama-36 ukusuka kumhla wokwenziwa.
- Ukuxilongwa kokuqala kweempazamo kufuneka kuqhutywe ngumsebenzisi. Nangona kunjalo, ngesicelo, i-LSELECTRIC okanye abameli bayo banokuwenza lo msebenzi ngentlawulo. Ukuba unobangela wesiphoso ufunyaniswa uxanduva lwe-LS ELECTRIC, le nkonzo iya kuba simahla.
- Ukukhutshwa kwiwaranti
- Ukutshintshwa kwezinto ezisetyenziswayo nezinobomi kuphela (umz. iireyiyidi, iifuse, iicapacitor, iibhetri, iiLCDs, njl.njl.)
- Ukusilela okanye umonakalo obangelwe ziimeko ezingafanelekanga okanye ukuphatha ngaphandle kwezo zichazwe kwincwadana yomsebenzisi
- Ukungaphumeleli okubangelwa yimiba yangaphandle engahambelani nemveliso
- Ukusilela okubangelwa luhlengahlengiso ngaphandle kwemvume ye-LS ELECTRIC
- Ukusetyenziswa kwemveliso ngeendlela ebezingalindelekanga
- Ukusilela okungenakuxelwa kwangaphambili/ukusonjululwa bubuchwephesha bezenzululwazi bangoku ngexesha lokwenziwa
- Ukusilela ngenxa yezinto zangaphandle ezifana nomlilo, umthamo ongaqhelekangatage, okanye iintlekele zendalo
- Ezinye iimeko apho i-LS ELECTRIC ayinaxanduva
- Ngolwazi oluneenkcukacha lwewaranti, nceda ujonge kwincwadana yomsebenzisi.
- Umxholo wesikhokelo sokufakela unokutshintsha ngaphandle kwesaziso sokuphucula ukusebenza kwemveliso.
ULUHLU LOQHAGAMSHELWANO
- I-LS ELECTRIC Co., Ltd.
- www.ls-electric.com
- I-imeyile: automation@ls-electric.com
- Ikomkhulu/iOfisi yaseSeoul
Umnxeba: 82-2-2034-4033,4888,4703 - LS ELECTRIC IOfisi yaseShanghai (eTshayina)
Umnxeba: 86-21-5237-9977 - I-LS ELECTRIC (Wuxi) Co., Ltd. (Wuxi, China)
Umnxeba: 86-510-6851-6666 - I-LS-ELECTRIC Vietnam Co., Ltd. (eHanoi, eVietnam)
Umnxeba: 84-93-631-4099 - I-LS ELECTRIC Middle East FZE (Dubai, UAE)
Umnxeba: 971-4-886-5360 - LS ELECTRIC Europe BV (Hoofddorf, Netherlands)
Umnxeba: 31-20-654-1424 - I-LS ELECTRIC Japan Co., Ltd. (eTokyo, eJapan)
Umnxeba: 81-3-6268-8241 - LS ELECTRIC America Inc. (Chicago, USA)
Ifowuni: 1-800-891-2941
Amaxwebhu / Izibonelelo
 |
LS XB Series Programmable Logic Controller [pdf] Isikhokelo soFakelo XB E C-DR10-14-20-30E, XB E C-DN10-14-20-30E, XB E C-DP10-14-20-30E, XB Series Programmable Logic Controller, XB Series, Programmable Logic Controller, Logic Umlawuli, uMlawuli |