masibus MAS-AO-08-D Analog Output Field Interface Board
Masibus Analog Output Field Interface Board e na le likanale tse 8 tse amohelang mefuta e fapaneng ea hona joale/voltage e fana ka matšoao le ho e fetolela ho ea hona joale / voltage lipontšo. Ke seporo sa compact universal DIN se kentsoeng ka likhokahano tse ngotsoeng le tse hlahisoang. Litokiso tse ikemetseng tsa zero & span bakeng sa kanale ka 'ngoe lia khoneha.
KOPO
- Eliminate Ground Loop problems
- Protect Expensive control systems against Field Faults
- Isolate and Translate System Signals
- Field Interface for PLC/DCS/SCADA systems
TS'ELISO
Kenyeletso
- No. of Channels & Type 8 Channel DC Volt/Current (Factory Set)
- Mefuta e Kenyelitsoeng
- Bakeng sa Moqtage: 1-5VDC,0-5VDC,0-10VDC
- For Current: 4-20ma, 0-20ma
- Input Impedance Current I/P: 100 Ohms, Voltage I/P :> 5M
I/P connection MKDS or 25pin D Type connector - Sephetho
- Mofuta oa Sephetho
- Moqtage/ Hajoale
- Sehlahisoa se hlahisoang
- Bakeng sa Moqtage: 1-5VDC,0-5VDC,0-10VDC
- For Current: 4-20mA, 0-20ma
- Output Load resistance
- 0/1 to 5V@ 1KΩ min,
- 0 to 10V@ 3KΩ min
- 0/4mA to 20mA@750Ω max
- Fault LED Indication
- Red LED for over/under range (1-5V/4-20mA only)
- Response Time ≤20milisecond
- Accuracy 0.1% of output span
- Drift 0.1% per Year
- Calibration Zero & Span Individual per channel by multi-turn trim pots O/P connection MKDS connector
Phepelo ea motlakase
- Power Supply 24VDC ±10%
- Power Consumption < 12VA
- Fuse Rating 2Amp (E Fokotse kapele)
- LED Indication Green LED – Healthy Status, Red LED –Fault Status
- Isolation 1.5KV AC Input to Power, Output to Output and Input to Output , Output to Power
Tikoloho
- Operating temperature Operating at 0 to 50C
- Temp. Co-efficient ≤ 100 PPM
- Relative humidity 30 to 95% RH non- condense
- Environmental Protection Conformal Coating on PCB
Ea nama
- Mounting Type DIN Rail (35 mm width)
- Dimensions 225(L) x 90(W) x 90(D)
- Weight Approx 400 gm
Terminal Qaqileng
- Terminal Block UL, CSA standard
- Terminal Cable Size up to 2.5mm² conductor
- 8 channel configurations
- Wide range of DC inputs and outputs
- Independent zero & span for each channel
- Ho bonolo ho lekanya
- Accepts non-std. signal input option
- Seporo sa DIN se kentsoe
- Boholo ba compact
Boemo
EA-225 (L) x 90 (W) x 90 (D)
TS'IRELETSO LE TEMOSO
As MAS-AO-08-D with front panel potentiometer calibration, must not be exposed to heavy shocks or vibration which may cause SCM to get out of calibration. To avoid Electrostatic Discharge (ESD) to the SCM, which may cause permanent damage, always ground yourself by touching some ground equipment. Before installation or beginning of any troubleshooting procedures the power to all equipment must be switched off and isolated. Units suspected of being faulty must be disconnected and removed first and brought to a properly equipped workshop for testing and repair. Component replacement and internal adjustments must be made by a company person only. Wiring must be carried out by personnel, who have basic electrical knowledge and practical experience. All wiring must confirm to appropriate standards of good practice and local codes and regulations. Wiring must be suitable for voltage, hona joale, le tekanyo ea mocheso oa tsamaiso. Hlokomela hore u se ke ua tiisa li-screws tsa theminale ho feta tekano.
KHOPOTSO
Lintlha tsa Taolo
| Item nos. | Lintlha |
| 1 | Main Power supply with electronic grounding |
| 2 | Fuse Fail LED indication |
| 3 | Power ON LED indication |
| 4 | MKDS Interface connector to DCS |
| 5 | 25 Pin D type Male interface connector to DCS |
| 6 | Field output terminals |
| 7 | Product serial no. |
Lintlha tsa khokahano
Connect rated power at terminal where 24vdc+ & 24VDC- is described in the wiring diagram. Field Input/output Terminals: Connect input between terminal where Input+ & Input- for particular channel for Input Or 25 pin D type PCB mounted male connector & take output from where Output+ & Output- described in connection details.
Lintlha tsa Khokahano ea Kena bakeng sa Mofuta oa 25 Pin D
| Pin No. | Tlhaloso |
| 1 | Input0+ |
| 2 | Input0- |
| 3 | Input1+ |
| 4 | Input1- |
| 5 | Input2+ |
| 6 | Input2- |
| 7 | Input3+ |
| 8 | Input3- |
| 9 | Input4+ |
| 10 | Input4- |
| 11 | Input5+ |
| 12 | Input5- |
| 13 | Input6+ |
| 14 | Input6- |
| 15 | Input7+ |
| 16 | Input7- |
TIISETSA SEAKI
KEKETSO
Ho hlongoa:
Place the module with the DIN rail guide way on the bottom edge of the DIN rail and then snap it downwards. The housing is mounted on the DIN rail by swiveling it into place. The Horizontal mounting arrangement Shown here, allows good vertical air circulation .It is also recommended to keep the adequate gap between two SCM.
Ho tlosoa:
Lokolla ho ts'oaroa ha snap-on u sebelisa screwdriver ebe u hula mojule ho tloha pheletsong e tlase ea DIN Rail.
TAORA KHOUTU
| TAORA KHOUTU | ||||||
|
Mohlala |
Mofuta oa Kenyeletso & Range | Mofuta oa Output & Range |
Khokahano ea ho Kena |
|||
| MAS-AO- 08-D | x | x | x | |||
| C | 4-20mA | C | 4-20mA | 0 | PCB Terminal Block | |
| D | 0-20mA | D | 0-20mA | 1 | D Type connector | |
| E | 1-5VDC | E | 1-5VDC | |||
| F | 0-5VDC | F | 0-5VDC | |||
| G | 0-10VDC | G | 0-10VDC | |||
| S | E khethehileng | S | E khethehileng | |||
| KHOUTU YA HO OTA KHABANE | ||
| Mohlala | Mofuta oa Kenyeletso & Range | |
| m-PC-D25F-LG | XX | |
| C | 2.5 Limithara | |
| D | 3.0 Limithara | |
| E | 3.5 Limithara | |
| F | 5.0 Limithara | |
| G | 7.0 Limithara | |
| S | E khethehileng | |
HO BATLE PHOSO
Unit Not Turning ON?
If RED LED on the module is ON, then the problem can be bad connection or due to incorrect rating of power fuse blows. If GREEN LED on the module is ON, it indicates the module is in healthy condition.
Unstable/Vague Reading
Sheba lihokelo tse hlephileng.
First verify that all conventional instrumentation norms have been followed for wiring. Make noise away from the module. Check for ripple on power supplies of Input & Output section. Output not matching with the expected value Kindly make sure that the output is really incorrect with respect to input signal before attempting any re-calibration.
Fluctuation in Reading
The reason can be reverse input connections.
Masibus Automation & Instrumentation Pvt. Ltd.
- B/30, GIDC Electronics Estate, Sector- 25,
- Gandhinagar-382044, Gujarat, India
- Ph: +91 79 23287275-77
- Lengolo-tsoibila: support@masibus.com
- Web: www.masibus.com
LBH
- Q: MAS-AO-08-D e na le likanale tse kae?
- A: MAS-AO-08-D e na le likanale tse 8.
- P: Ke mocheso ofe oa mocheso o sebetsang oa sehlahisoa?
- A: The product operates at temperatures ranging from 0 to 50°C.
- P: Nka lekanya tlhahiso ea mocha ka mong joang?
- A: Calibration for zero & span for each channel can be adjusted individually using multi-turn trim pots.
Litokomane / Lisebelisoa
 |
masibus MAS-AO-08-D Analog Output Field Interface Board [pdf] Bukana ea Mosebelisi MAS-AO-08-D Analog Output Field Interface Board, MAS-AO-08-D, Analog Output Field Interface Board, Output Field Interface Board, Field Interface Board, Boto ea Interface |