masibus MAS-AO-08-D Analog Output Field Interface Board
Masibus Analog Output Field Interface Board has 8 channels that accepts various types of current/voltage signals and converts them to isolated current/voltage signals. It is compact universal DIN rail mounted with labeled input and output connections. Independent zero & span adjustment for each channel is possible.
УЖЫВАННЕ
- Eliminate Ground Loop problems
- Protect Expensive control systems against Field Faults
- Isolate and Translate System Signals
- Field Interface for PLC/DCS/SCADA systems
СПЕЦЫФІКАЦЫЯ
Увод
- No. of Channels & Type 8 Channel DC Volt/Current (Factory Set)
- Уваходны дыяпазон
- Для тtage: 1-5VDC,0-5VDC,0-10VDC
- For Current: 4-20ma, 0-20ma
- Input Impedance Current I/P: 100 Ohms, Voltage I/P :> 5M
I/P connection MKDS or 25pin D Type connector - Выхад
- Тып вываду
- тtagд/ Бягучы
- Выхадны дыяпазон
- Для тtage: 1-5VDC,0-5VDC,0-10VDC
- For Current: 4-20mA, 0-20ma
- Output Load resistance
- 0/1 to 5V@ 1KΩ min,
- 0 to 10V@ 3KΩ min
- 0/4mA to 20mA@750Ω max
- Fault LED Indication
- Red LED for over/under range (1-5V/4-20mA only)
- Response Time ≤20milisecond
- Accuracy 0.1% of output span
- Drift 0.1% per Year
- Calibration Zero & Span Individual per channel by multi-turn trim pots O/P connection MKDS connector
Блок харчавання
- Power Supply 24VDC ±10%
- Power Consumption < 12VA
- Номінал засцерагальніка 2Amp (Хутка ўздуты)
- LED Indication Green LED – Healthy Status, Red LED –Fault Status
- Isolation 1.5KV AC Input to Power, Output to Output and Input to Output , Output to Power
Экалагічныя
- Operating temperature Operating at 0 to 50C
- Temp. Co-efficient ≤ 100 PPM
- Relative humidity 30 to 95% RH non- condense
- Environmental Protection Conformal Coating on PCB
фізічны
- Mounting Type DIN Rail (35 mm width)
- Dimensions 225(L) x 90(W) x 90(D)
- Weight Approx 400 gm
Дэталь тэрмінала
- Terminal Block UL, CSA standard
- Terminal Cable Size up to 2.5mm² conductor
- 8 channel configurations
- Wide range of DC inputs and outputs
- Independent zero & span for each channel
- Лёгка адкалібраваць
- Accepts non-std. signal input option
- Усталяваны на DIN-рэйку
- Кампактны памер
Вымярэнне
225 (Д) х 90 (Ш) х 90 (Г)
БЕЗПЕКА І ПАПЯРЭДЖАННЕ
As MAS-AO-08-D with front panel potentiometer calibration, must not be exposed to heavy shocks or vibration which may cause SCM to get out of calibration. To avoid Electrostatic Discharge (ESD) to the SCM, which may cause permanent damage, always ground yourself by touching some ground equipment. Before installation or beginning of any troubleshooting procedures the power to all equipment must be switched off and isolated. Units suspected of being faulty must be disconnected and removed first and brought to a properly equipped workshop for testing and repair. Component replacement and internal adjustments must be made by a company person only. Wiring must be carried out by personnel, who have basic electrical knowledge and practical experience. All wiring must confirm to appropriate standards of good practice and local codes and regulations. Wiring must be suitable for voltagэлектрычны, ток і тэмпературны паказчык сістэмы. Будзьце асцярожныя, каб не перацягнуць шрубы клем.
ЗЛУЧЭННЕ
Элементы кіравання
| Item nos. | Дэталі |
| 1 | Main Power supply with electronic grounding |
| 2 | Fuse Fail LED indication |
| 3 | Power ON LED indication |
| 4 | MKDS Interface connector to DCS |
| 5 | 25 Pin D type Male interface connector to DCS |
| 6 | Field output terminals |
| 7 | Product serial no. |
Падрабязнасці злучэння
Connect rated power at terminal where 24vdc+ & 24VDC- is described in the wiring diagram. Field Input/output Terminals: Connect input between terminal where Input+ & Input- for particular channel for Input Or 25 pin D type PCB mounted male connector & take output from where Output+ & Output- described in connection details.
Input Connection Details for 25 Pin D Type
| Кантактны нумар | Апісанне |
| 1 | Input0+ |
| 2 | Input0- |
| 3 | Input1+ |
| 4 | Input1- |
| 5 | Input2+ |
| 6 | Input2- |
| 7 | Input3+ |
| 8 | Input3- |
| 9 | Input4+ |
| 10 | Input4- |
| 11 | Input5+ |
| 12 | Input5- |
| 13 | Input6+ |
| 14 | Input6- |
| 15 | Input7+ |
| 16 | Input7- |
БЛОКАВАЯ СХЕМА
УСТАНОВКА
Мантаж:
Place the module with the DIN rail guide way on the bottom edge of the DIN rail and then snap it downwards. The housing is mounted on the DIN rail by swiveling it into place. The Horizontal mounting arrangement Shown here, allows good vertical air circulation .It is also recommended to keep the adequate gap between two SCM.
Выдаленне:
Адпусціце зашчапку з дапамогай адвёрткі, а затым адлучыце модуль ад ніжняга краю DIN-рэйкі.
КОД ЗАКАЗА
| КОД ЗАКАЗА | ||||||
|
мадэль |
Тып і дыяпазон уваходу | Тып і дыяпазон выхаду |
Уваходнае злучэнне |
|||
| MAS-AO- 08-D | x | x | x | |||
| C | 4-20 мА | C | 4-20 мА | 0 | PCB Terminal Block | |
| D | 0-20 мА | D | 0-20 мА | 1 | D Type connector | |
| E | 1-5 В пастаяннага току | E | 1-5 В пастаяннага току | |||
| F | 0-5 В пастаяннага току | F | 0-5 В пастаяннага току | |||
| G | 0-10 В пастаяннага току | G | 0-10 В пастаяннага току | |||
| S | Асаблівы | S | Асаблівы | |||
| КОД ЗАМОВЫ КАБЕЛЯ | ||
| мадэль | Тып і дыяпазон уваходу | |
| m-PC-D25F-LG | XX | |
| C | 2.5 метраў | |
| D | 3.0 метраў | |
| E | 3.5 метраў | |
| F | 5.0 метраў | |
| G | 7.0 метраў | |
| S | Асаблівы | |
УСТРАНЕННЕ НЕПРАЎДАЎ
Прылада не ўключаецца?
If RED LED on the module is ON, then the problem can be bad connection or due to incorrect rating of power fuse blows. If GREEN LED on the module is ON, it indicates the module is in healthy condition.
Unstable/Vague Reading
Праверце аслабленыя злучэнні.
First verify that all conventional instrumentation norms have been followed for wiring. Make noise away from the module. Check for ripple on power supplies of Input & Output section. Output not matching with the expected value Kindly make sure that the output is really incorrect with respect to input signal before attempting any re-calibration.
Fluctuation in Reading
The reason can be reverse input connections.
Masibus Automation & Instrumentation Pvt. Ltd.
- B/30, GIDC Electronics Estate, Sector- 25,
- Gandhinagar-382044, Gujarat, India
- Тэл.: +91 79 23287275-77
- электронная пошта: support@masibus.com
- Web: www.masibus.com
FAQ
- Q: How many channels does the MAS-AO-08-D have?
- A: The MAS-AO-08-D has 8 channels.
- Q: Які дыяпазон працоўных тэмператур прадукту?
- A: The product operates at temperatures ranging from 0 to 50°C.
- Q: How can I calibrate the output for each channel?
- A: Calibration for zero & span for each channel can be adjusted individually using multi-turn trim pots.
Дакументы / Рэсурсы
 |
masibus MAS-AO-08-D Analog Output Field Interface Board [pdfКіраўніцтва карыстальніка MAS-AO-08-D Analog Output Field Interface Board, MAS-AO-08-D, Analog Output Field Interface Board, Output Field Interface Board, Field Interface Board, Interface Board |