masibus MAS-AO-08-D Bord tal-Interfaċċa tal-Qasam tal-Output Analog
Masibus Analog Output Field Interface Bord għandu 8 kanali li jaċċettaw diversi tipi ta 'kurrent / voltage sinjali u tikkonvertihom għal kurrent iżolat/voltage sinjali. Huwa ferrovija DIN universali kompatta immuntata b'konnessjonijiet ta 'input u output ittikkettjati. Aġġustament indipendenti żero & span għal kull kanal huwa possibbli.
APPLIKAZZJONI
- Eliminate Ground Loop problems
- Protect Expensive control systems against Field Faults
- Isolate and Translate System Signals
- Field Interface for PLC/DCS/SCADA systems
SPEĊIFIKAZZJONI
Input
- No. of Channels & Type 8 Channel DC Volt/Current (Factory Set)
- Medda tad-dħul
- Għal Voltage: 1-5VDC,0-5VDC,0-10VDC
- For Current: 4-20ma, 0-20ma
- Input Impedance Current I/P: 100 Ohms, Voltage I/P :> 5M
I/P connection MKDS or 25pin D Type connector - Output
- Tip ta' Output
- Voltage/ Kurrent
- Firxa tal-Output
- Għal Voltage: 1-5VDC,0-5VDC,0-10VDC
- For Current: 4-20mA, 0-20ma
- Output Reżistenza tat-tagħbija
- 0/1 to 5V@ 1KΩ min,
- 0 to 10V@ 3KΩ min
- 0/4mA to 20mA@750Ω max
- Fault LED Indication
- Red LED for over/under range (1-5V/4-20mA only)
- Response Time ≤20milisecond
- Accuracy 0.1% of output span
- Drift 0.1% per Year
- Calibration Zero & Span Individual per channel by multi-turn trim pots O/P connection MKDS connector
Provvista ta' enerġija
- Power Supply 24VDC ±10%
- Power Consumption < 12VA
- Klassifikazzjoni tal-fjus 2Amp (Minfuħ Malajr)
- LED Indication Green LED – Healthy Status, Red LED –Fault Status
- Isolation 1.5KV AC Input to Power, Output to Output and Input to Output , Output to Power
Ambjentali
- Operating temperature Operating at 0 to 50C
- Temp. Co-efficient ≤ 100 PPM
- Relative humidity 30 to 95% RH non- condense
- Environmental Protection Conformal Coating on PCB
Fiżiku
- Mounting Type DIN Rail (35 mm width)
- Dimensions 225(L) x 90(W) x 90(D)
- Weight Approx 400 gm
Dettall tat-Terminal
- Terminal Block UL, CSA standard
- Terminal Cable Size up to 2.5mm² conductor
- 8 channel configurations
- Wide range of DC inputs and outputs
- Independent zero & span for each channel
- Faċli biex tikkalibra
- Accepts non-std. signal input option
- ferrovija DIN immuntati
- Daqs Kompatt
Dimensjoni
225(L) x 90(W) x 90(D)
SIGURTÀ U TWISSIJA
As MAS-AO-08-D with front panel potentiometer calibration, must not be exposed to heavy shocks or vibration which may cause SCM to get out of calibration. To avoid Electrostatic Discharge (ESD) to the SCM, which may cause permanent damage, always ground yourself by touching some ground equipment. Before installation or beginning of any troubleshooting procedures the power to all equipment must be switched off and isolated. Units suspected of being faulty must be disconnected and removed first and brought to a properly equipped workshop for testing and repair. Component replacement and internal adjustments must be made by a company person only. Wiring must be carried out by personnel, who have basic electrical knowledge and practical experience. All wiring must confirm to appropriate standards of good practice and local codes and regulations. Wiring must be suitable for voltage, kurrenti, u klassifikazzjoni tat-temperatura tas-sistema. Oqgħod attent li ma tissikkax iżżejjed il-viti tat-terminal.
KONNESSJONI
Elementi ta' Kontroll
| Item nos. | Dettalji |
| 1 | Main Power supply with electronic grounding |
| 2 | Fuse Fail LED indication |
| 3 | Power ON LED indication |
| 4 | MKDS Interface connector to DCS |
| 5 | 25 Pin D type Male interface connector to DCS |
| 6 | Field output terminals |
| 7 | Product serial no. |
Dettalji tal-konnessjoni
Connect rated power at terminal where 24vdc+ & 24VDC- is described in the wiring diagram. Field Input/output Terminals: Connect input between terminal where Input+ & Input- for particular channel for Input Or 25 pin D type PCB mounted male connector & take output from where Output+ & Output- described in connection details.
Dettalji tal-Konnessjoni tal-Input għal 25 Pin D Tip
| Pin numru | Deskrizzjoni |
| 1 | Input0+ |
| 2 | Input0- |
| 3 | Input1+ |
| 4 | Input1- |
| 5 | Input2+ |
| 6 | Input2- |
| 7 | Input3+ |
| 8 | Input3- |
| 9 | Input4+ |
| 10 | Input4- |
| 11 | Input5+ |
| 12 | Input5- |
| 13 | Input6+ |
| 14 | Input6- |
| 15 | Input7+ |
| 16 | Input7- |
DIJAGRAMA TAL-BLOKK
INSTALLAZZJONI
Immuntar:
Place the module with the DIN rail guide way on the bottom edge of the DIN rail and then snap it downwards. The housing is mounted on the DIN rail by swiveling it into place. The Horizontal mounting arrangement Shown here, allows good vertical air circulation .It is also recommended to keep the adequate gap between two SCM.
Tneħħija:
Erħi l-qabda snap-on billi tuża tornavit u mbagħad aqla 'l-modulu mit-tarf ta' isfel tal-Ferrovija DIN.
KODIĊI TA' ORDNI
| KODIĊI TA' ORDNI | ||||||
|
Mudell |
Tip ta' Input & Medda | Output Tip & Medda |
Konnessjoni tal-Input |
|||
| MAS-AO- 08-D | x | x | x | |||
| C | 4-20mA | C | 4-20mA | 0 | PCB Terminal Block | |
| D | 0-20mA | D | 0-20mA | 1 | D Type connector | |
| E | 1-5VDC | E | 1-5VDC | |||
| F | 0-5VDC | F | 0-5VDC | |||
| G | 0-10VDC | G | 0-10VDC | |||
| S | Speċjali | S | Speċjali | |||
| KODIĊI TA' ORDNI TAL-CABLE | ||
| Mudell | Tip ta' Input & Medda | |
| m-PC-D25F-LG | XX | |
| C | 2.5 Meter | |
| D | 3.0 Meter | |
| E | 3.5 Meter | |
| F | 5.0 Meter | |
| G | 7.0 Meter | |
| S | Speċjali | |
SPARJAZZJONI TAL-PROBLEMI
L-Unità Mhux Qed Tixgħel?
If RED LED on the module is ON, then the problem can be bad connection or due to incorrect rating of power fuse blows. If GREEN LED on the module is ON, it indicates the module is in healthy condition.
Unstable/Vague Reading
Iċċekkja għal konnessjonijiet laxki.
First verify that all conventional instrumentation norms have been followed for wiring. Make noise away from the module. Check for ripple on power supplies of Input & Output section. Output not matching with the expected value Kindly make sure that the output is really incorrect with respect to input signal before attempting any re-calibration.
Fluctuation in Reading
The reason can be reverse input connections.
Masibus Automation & Instrumentation Pvt. Ltd.
- B/30, GIDC Electronics Estate, Sector- 25,
- Gandhinagar-382044, Gujarat, India
- Ph: +91 79 23287275-77
- Email: support@masibus.com
- Web: www.masibus.com
FAQ
- Q: Kemm-il kanal għandu l-MAS-AO-08-D?
- A: Il-MAS-AO-08-D għandu 8 kanali.
- Q: X'inhi l-firxa tat-temperatura operattiva tal-prodott?
- A: The product operates at temperatures ranging from 0 to 50°C.
- Q: Kif nista 'nikkalibra l-output għal kull kanal?
- A: Calibration for zero & span for each channel can be adjusted individually using multi-turn trim pots.
Dokumenti / Riżorsi
 |
masibus MAS-AO-08-D Bord tal-Interfaċċa tal-Qasam tal-Output Analog [pdfGwida għall-Utent MAS-AO-08-D Bord tal-Interfaċċa tal-Qasam tal-Output Analog, MAS-AO-08-D, Bord tal-Interfaċċa tal-Qasam tal-Output Analog, Bord tal-Interfaċċa tal-Qasam tal-Output, Bord tal-Interfaċċa tal-Qasam, Bord tal-Interface |