masibus MAS-AO-08-D Analog mmepụta Ubi Interface Board
Masibus Analog Output Field Interface Board nwere ọwa 8 na-anabata ụdị dị iche iche nke ugbu a/voltage na-egosi ma tụgharịa ha ka ọ bụrụ nke dịpụrụ adịpụ/voltage mgbama. Ọ bụ kọmpat ụgbọ okporo ígwè DIN zuru ụwa ọnụ nke etinyere ya na njikọ ntinye na mmepụta akara. Ndozi efu na ogologo oge maka ọwa ọ bụla ga-ekwe omume.
Ngwa
- Wepụ nsogbu Ground Loop
- Chebe sistemu njikwa dị oke ọnụ megide mmejọ ubi
- Kewapụ ma tụgharịa asụsụ mgbaàmà Sistemu
- Ubi Interface maka sistemụ PLC/DCS/SCADA
Nkọwapụta
Ntinye
- Nọmba nke ọwa & Ụdị 8 Channel DC Volt/Ugbu a (Ntọala Ụlọ Ọrụ)
- Oke ntinye
- Maka Voltage: 1-5VDC,0-5VDC,0-10VDC
- Maka ugbu a: 4-20ma, 0-20ma
- Ntinye ihe mgbochi I/P dị ugbu a: 100 Ohms, Voltage I/P:> 5M
Njikọ I/P MKDS ma ọ bụ 25pin D Ụdị njikọ - Mpụta
- Ụdị mmepụta
- Voltage/ Ugbu a
- Oke mmepụta
- Maka Voltage: 1-5VDC,0-5VDC,0-10VDC
- Maka ugbu a: 4-20mA, 0-20ma
- Mmegide Ibu Ibu
- 0/1 ruo 5V@ 1KΩ nkeji,
- 0 ruo 10V@ 3KΩ min
- 0/4mA ruo 20mA@750Ω max
- Ngosipụta ikanam mmejọ
- Uhie uhie maka ihe karịrị / n'okpuru oke (1-5V/4-20mA naanị)
- Oge nzaghachi ≤20mili sekọnd
- Izizi 0.1% nke ogologo mmepụta
- Na-ebugharị 0.1% kwa afọ
- Calibration Zero & Span Onye n'otu n'otu n'otu ọwa site n'ọtụtụ ntụgharị mkpụbelata ite O/P njikọ MKDS
Ịnye ọkụ
- Nkwanye ike 24VDC ± 10%
- Oriri ike <12VA
- Ogo Fuse 2Amp (Ọsọ ọsọ)
- Ngosipụta LED LED LED - Ọnọdụ ahụike, Ikanam uhie - Ọnọdụ mmejọ
- Mwepu 1.5KV AC ntinye aka na ike, ntinye na ntinye na ntinye aka, ntinye na ike
gburugburu ebe obibi
- Ọnọdụ okpomọkụ na-arụ ọrụ na 0 ruo 50C
- Okpomọkụ Ndị na-arụkọ ọrụ ọnụ ≤ 100 PPM
- Iru mmiri dị n'etiti 30 ruo 95% RH na-abụghị condens
- Mkpuchi Conformal Nchekwa gburugburu na PCB
Anụ ahụ
- Ụdị mgbakwasị ụkwụ DIN Rail (obosara 35mm)
- Akụkụ 225(L) x 90(W) x 90(D)
- Ibu ihe dịka 400 gm
Nkọwa njedebe
- Terminal Block UL, ọkọlọtọ CSA
- Nha eriri ọdụ ruo 2.5mm² eduzi
- Nhazi ọwa 8
- Ihe ntinye na ntinye DC sara mbara
- efu & span nọọrọ onwe maka ọwa ọ bụla
- Ọ dị mfe ịhazi
- Nabata na-abụghị std. nhọrọ ntinye mgbaàmà
- DIN okporo ígwè agbakwunyere
- Oke kọmpat
Akụkụ
225(L) x 90(W) x 90(D)
Nchekwa na ịdọ aka ná ntị
Dị ka MAS-AO-08-D na n'ihu panel potentiometer calibration, ekwesighi ka ekpughere ya na nnukwu ujo ma ọ bụ ịma jijiji nke nwere ike ime ka SCM pụọ na nhazi. Iji zere ịgbasa ọkụ eletrik (ESD) gaa na SCM, nke nwere ike ibute mmebi na-adịgide adịgide, na-agbada onwe gị mgbe niile site na imetụ ụfọdụ akụrụngwa ala aka. Tupu echichi ma ọ bụ mmalite nke usoro nchọpụta nsogbu ọ bụla a ga-agbanyụrịrị ike na akụrụngwa niile ma kewapụ ya. A ga-ewepụrịrị nkeji ndị a na-enyo enyo na ha ezighi ezi ma buru ụzọ weta ya na ụlọ ọrụ a kwadebere nke ọma maka nnwale na nrụzi. Ọ bụ naanị onye ụlọ ọrụ ga-emerịrị ngbanwe akụrụngwa na mgbanwe n'ime. A ghaghị ịrụ ọrụ wiring site na ndị ọrụ, ndị nwere ihe ọmụma eletrik bụ isi na ahụmahụ bara uru. Wiring niile ga-akwadorịrị ụkpụrụ kwesịrị ekwesị nke omume ọma yana koodu na ụkpụrụ mpaghara. Wiring ga-adabara voltage, ugbu a, na ọnọdụ okpomọkụ nke sistemụ. Kpachara anya ka ị ghara imechi skru ọnụ ọnụ.
Njikọ
Ihe njikwa
| Ihe mba. | Nkọwa |
| 1 | Isi ike na-enye ala eletrik |
| 2 | Ihe ngosi ọkụ Fuse Fail LED |
| 3 | Ike ON LED egosi |
| 4 | MKDS Interface njikọ na DCS |
| 5 | 25 Pin D ụdị njikọ njikọ nwoke na DCS |
| 6 | Ọnụ ọnụ mmepụta ubi |
| 7 | Oghere ngwaahịa nọmba. |
Nkọwa njikọ
Jikọọ ike akwadoro na ọnụ ebe 24vdc+ & 24VDC- kọwara na eserese wiring. Ngwunye ntinye/mpụta ihe ubi: Jikọọ ntinye n'etiti ọnụ ebe ntinye+ & ntinye - maka ọwa pụrụ iche maka ntinye ma ọ bụ 25 pin D ụdị PCB kwadoro nwoke njikọ & wepụta mmepụta site na ebe mmepụta+ & mmepụta- kọwara na nkọwa njikọ.
Nkọwa njikọ ntinye maka ụdị pin D 25
| Pin Nke | Nkọwa |
| 1 | Ntinye 0+ |
| 2 | Ntinye 0- |
| 3 | Ntinye 1+ |
| 4 | Ntinye 1- |
| 5 | Ntinye 2+ |
| 6 | Ntinye 2- |
| 7 | Ntinye 3+ |
| 8 | Ntinye 3- |
| 9 | Ntinye 4+ |
| 10 | Ntinye 4- |
| 11 | Ntinye 5+ |
| 12 | Ntinye 5- |
| 13 | Ntinye 6+ |
| 14 | Ntinye 6- |
| 15 | Ntinye 7+ |
| 16 | Ntinye 7- |
GOCKWUO DIAGRAM
Ịwụnye
Ịkwanye:
Debe modul ahụ na ụzọ ntuziaka ụgbọ okporo ígwè DIN na nsọtụ ala nke ụgbọ okporo ígwè DIN wee jide ya ala. A na-etinye ụlọ ahụ n'ọdụ ụgbọ okporo ígwè DIN site na ịgbanye ya n'ime ebe. Nhazi ịrị elu kwụ ọtọ Egosiri ebe a, na-enye ohere ikuku ikuku kwụ ọtọ .A na-atụ aro ka idobe oghere zuru oke n'etiti SCM abụọ.
Mwepụ:
Hapụ ọnyà ahụ site na iji screwdriver wee wepụ modul ahụ na nsọtụ ala nke DIN Rail.
KỌDỤ NKWUKWU
| KỌDỤ NKWUKWU | ||||||
|
Nlereanya |
Ụdị ntinye & Oke | Ụdị mmepụta & oke |
Ntinye njikọ |
|||
| MAS-AO- 08-D | x | x | x | |||
| C | 4-20mA | C | 4-20mA | 0 | Ihe mgbochi PCB | |
| D | 0-20mA | D | 0-20mA | 1 | D Ụdị njikọ | |
| E | 1-5VDC | E | 1-5VDC | |||
| F | 0-5VDC | F | 0-5VDC | |||
| G | 0-10VDC | G | 0-10VDC | |||
| S | Pụrụ iche | S | Pụrụ iche | |||
| KỌDỤ NKWUKWU CABLE | ||
| Nlereanya | Ụdị ntinye & Oke | |
| m-PC-D25F-LG | XX | |
| C | 2.5 mita | |
| D | 3.0 mita | |
| E | 3.5 mita | |
| F | 5.0 mita | |
| G | 7.0 mita | |
| S | Pụrụ iche | |
Ịgbapụ nsogbu
Nkeji anaghị agbanwuo?
Ọ bụrụ na ọkụ ọkụ na-acha uhie uhie na modul dị, mgbe ahụ nsogbu ahụ nwere ike ịbụ njikọ ọjọọ ma ọ bụ n'ihi ọkwa na-ezighị ezi nke ọkụ ọkụ ọkụ. Ọ bụrụ na GREEN LED na modul dị, ọ na-egosi na modul ahụ nọ n'ọnọdụ ahụike.
Ọgụgụ na-adịghị akwụsi ike/Vgue
Lelee maka njikọ adịghị mma.
Buru ụzọ chọpụta na esorola ụkpụrụ ngwa ngwa niile maka wiring. Mee mkpọtụ pụọ na modul. Lelee maka ripple na akụrụngwa ike nke ngalaba ntinye & mmepụta. Mmepụta anaghị adaba na uru a na-atụ anya ya, jide n'aka na mmepụta ezighi ezi n'ihe gbasara mgbama ntinye tupu ị nwaa nhazigharị ọ bụla.
Mgbanwe na Ọgụgụ
Ihe kpatara ya nwere ike bụrụ njikọ ntinye azụ.
Masibus Automation & Instrumentation Pvt. Ltd.
- B/30, GIDC Electronics Estate, ngalaba- 25,
- Gandhinagar-382044, Gujarat, India
- Ph: +91 79 23287275-77
- Email: support@masibus.com
- Web: www.masibus.com
FAQ
- Q: Olee otú ọtụtụ ọwa ka MAS-AO-08-D nwere?
- A: MAS-AO-08-D nwere ọwa 8.
- Ajụjụ: Gịnị bụ oke okpomọkụ na-arụ ọrụ nke ngwaahịa?
- A: Ngwaahịa a na-arụ ọrụ na okpomọkụ sitere na 0 ruo 50 Celsius.
- Ajụjụ: Kedu ka m ga-esi hazie mmepụta maka ọwa ọ bụla?
- A: Enwere ike idozi nhazi maka efu & span maka ọwa ọ bụla n'otu n'otu site na iji ite mkpụbelata ọtụtụ ntụgharị.
Akwụkwọ / akụrụngwa
 |
masibus MAS-AO-08-D Analog mmepụta Ubi Interface Board [pdf] Ntuziaka onye ọrụ MAS-AO-08-D Analog Mmepụta Ubi Interface Board, MAS-AO-08-D, Analọgụ Mmepụta Ubi Interface Board, Oghere Ntugharị Ubi, Ọkpụkpụ Ntugharị Ubi, Kọmpụta Interface |