DMX4ALL DMX Servo Control 2 RDM Interface Pixel LED Controller Manual

Li-servo tse nang le 5V ho fihla ho 12V DC li ka sebelisoa
Phepelo voltage ea DMX-Servo-Control 2 e pakeng tsa 5V le 12V. Litšebeletso tse nang le matla a phepelotage ka hare ho sebaka sena se ka kopanngoa ka ho toba.

Letšoao la taolo ea Servo e fetolehang
Taolo e etsahala ka bophara bo feto-fetohang ba pulse.

Moqapi oa Compact
Moqapi le mohaho o kopanetsoeng o lumella ho kenngoa ha kopano ena e nyenyane libakeng tse sa faneng ka sebaka se seholo.

LED-Bontša
LED e kopantsoeng ke pontšo e nang le mesebetsi e mengata bakeng sa ho bontša boemo ba lisebelisoa tsa hona joale.

Ho bua ka DMX
Aterese ea DMX e ka lokisoa ka sesebelisoa sa DIP sa maemo a 10.

RDM Tšehetso
DMX Servo Control 2 e lumella tlhophiso ka RDM holim'a DMX

Leqephe la lintlha

Phepelo ea motlakase: 5-12V DC 50mA ntle le servo e hokahantsoeng
Tsamaiso: DMX512 RDM
Servo-Moqolotage: 5-12V DC (e tsamaellana le phepelo ea voltage)
Servo-Power: max. 3A ka kakaretso bakeng sa li-servos ka bobeli
Likanale tsa DMX: Likanale tse 2
Khokahano: 1x screw terminal / 2pin 1x screw terminal / 3pin 2x hlooho ea pin RM2,54 / 3pin
Boemo: 30mm x 67 limilimithara

Litaba

1x DMX-Servo-Control 2
1x Quick manual Sejeremane le Senyesemane

Khokahano

TLHOKOMELO :
DMX-Servo-Control 2 ena HA E lumelloe bakeng sa lits'ebetso tse nang le litlhoko tse amanang le polokeho kapa moo maemo a kotsi a ka hlahang!

LED-Bontša

LED e kopantsoeng ke pontšo ea mesebetsi e mengata.

Nakong ea mokhoa o tloaelehileng oa ts'ebetso, mabone a LED a khantša ka ho sa feleng. Tabeng ena sesebelisoa se sebetsa.

Ho feta moo, LED e bontša boemo ba hona joale. Tabeng ena, lebone la LED le khantša ka likhahla tse khutšoane ebe ha le eo ka nako e telele.

Palo ea mabone a benyang e lekana le nomoro ea ketsahalo:

Boemo- Nomoro	Phoso	Tlhaloso
1	Ha ho na DMX	Ha ho na Aterese ea DMX
2	Ho lokisa phoso	Ka kopo, hlahloba hore na Aterese e nepahetseng ea DMX-Start e lokisoa ka DIP-Switches
4	Configurationstored	Sebopeho se fetotsoeng se bolokiloe

DMX-Aterese

Aterese ea ho Qala e ka fetoloa ka DIP-Switches.

Switjha 1 e na le valency 20 (=1), switjha 2 valency 21 (=2) joalo-joalo ho fihlela switjha9 ka valency 28 (=256).

Kakaretso ea li-switches tse bonts'ang ON e lekana le aterese ea ho qala.

Aterese ea ho qala ea DMX e ka boela ea lokisoa ho sebelisoa paramethara ea RDM DMX_START ADDRESS. Bakeng sa ts'ebetso ea RDM li-switches tsohle li tlameha ho hlophisoa ho TIMA!
Phetoho ea Aterese

Phetoho ea Aterese

Letšoao la taolo ea servo

Letšoao le romelloang ho Servo le na le Tšusumetso e Phahameng le e Tlase. Nako ea pulse e bohlokoa bakeng sa Servo.

Ka tloaelo tšusumetso ena e pakeng tsa 1ms le 2ms, eo hape e leng mokhoa o tloaelehileng oa DMX-Servo-Control 2. Tsena ke maemo a ho qetela a Servos moo e sa lekanyetsoang ka mechine. Bolelele ba pulse ea 1.5ms e ka ba boemo bo bohareng ba Servo.

Fetola lets'oao la taolo ea Servo

Ho ea ka Servo e sebelisitsoeng e ka ba advantagEous ho ikamahanya le nako tsa tshusumetso. Nako e fokolang ea boemo bo ka ho le letšehali e ka behoa ka har'a sebaka sa 0,1-2,5ms. Nako e phahameng ea boemo bo nepahetseng e tlameha ho ba kholo ho feta nako e fokolang mme e ka ba boholo ba 2,54ms.

Ka kopo, tsoela pele ka tsela e latelang bakeng sa litlhophiso:

Bulela DMX-Servo-Control
Seta DIP-Switch 9 le 10 ho OFF

Beha DIP-Switch 10 ho ON
Beha ka DIP-Switched 1-8 Nako e Bonyane

Beha DIP-Switch 9 ho ON
Beha ka DIP-Switched 1-8 nako e kholo

Seta DIP-Switch 10 ho tima
LED e khantša 4x e le tiiso ea hore li-setting li bolokiloe

Beha ka DIP-Switches 1-9 aterese ea DMX-Starting

Ho beha nako ho etsahala ka DMX-Addressing ka DIP-Switches ka mehato ea 10µs. Ka hona, boleng bo behiloeng ka 0,01ms boa atisoa, joalo ka mohlalaample boleng ba 100 bo hlahisa boleng ba 1ms.
Litekanyetso tsa RDM LEFT_ADJUST le RIGHT_ADJUST le tsona li ka sebelisoa ho hlophisa nako ea molumo.

RDM

(ho tsoa ho Hardware V2.1)
RDM ke foromo e khuts'oane ea Rmaikutlo Device Management.

Hang ha sesebelisoa se le ka har'a tsamaiso, litlhophiso tse itšetlehileng ka lisebelisoa li etsahala ka thōko ka taelo ea RDM ka lebaka la UID e khethehileng e fanoeng. Ho fihlella ka ho toba ho sesebelisoa ha ho hlokahale.

Haeba aterese ea ho qala ea DMX e setiloe ka RDM, li-switches tsohle tsa liaterese ho DMXServo-Control 2 li tlameha ho hlongoa ho TIMA! Aterese ea ho qala ea DMX e behiloeng ke li-addressswitches e lula e le pele!

Sesebelisoa sena se tšehetsa litaelo tse latelang tsa RDM:

ID ea paramethara	Ho sibolloa Taelo	HLOKOMELA Taelo	FUMANA Taelo	ANSI / PID
TLHOKOMELISOE_BRANCH				E1.20
DISC_MUTE				E1.20
DISC_UN_MUTE				E1.20
DEVICE_INFO				E1.20
SUPPORTED_PARAMETERS				E1.20
PARAMETER_DESCRIPTION				E1.20
SOFTWARE_VERSION_LABEL				E1.20
DMX_START_ADDRESS				E1.20
DEVICE_LABEL				E1.20
MANUFACTURER_LABEL				E1.20
DEVICE_MODEL_DESCRIPTION				E1.20
IDENTIFY_DEVICE				E1.20
LIEKETSENG DITLHARE				E1.20
DMX_PERSONALITY				E1.20
DMX_PERSONALITY_DESCRIPTION				E1.20
DISPLAY_LEVEL				E1.20
DMX_FAIL_MODE				E1.37

DMX-Servo-Control 2

ID ea paramethara	Taelo ea ho Fumana	HLOKOMELA Taelo	FUMANA Taelo	ANSI / PID
NOMORO EA LETOTO¹⁾				PID: 0xD400
LEFT_LETSA¹⁾				PID: 0xD450
HO JOALOKA_LETSA¹⁾				PID: 0xD451

Moetsi o itšetlehile ka litaelo tsa taolo ea RDM (MSC - Mofuta o Khethehileng oa Moetsi)

Moetsi ho latela litaelo tsa taolo ea RDM:

NOMORO EA LETOTO
PID: 0xD400

E hlahisa tlhaloso ea mongolo (ASCII-Text) ea nomoro ea serial ea sesebelisoa.
FUMANA Romela: PDL=0
Amohela: PDL=21 (21 Byte ASCII-Temana)

LEFT_LETSA
PID: 0xD450

E beha bolelele ba nako e phahameng bakeng sa boemo ba servo le letšehali.
FUMANA Romela: PDL=0
Amohela: PDL=2 (Lentswe le 1 LEFT_ADJUST_TIME)

SET Romela: PDL=2 (Lentswe le 1 LEFT_ADJUST_TIME)
Amohela: PDL=0

LEFT_ADJUSTTIME
200 - 5999

Funktion
WERT: x 0,5µs = Impulszeit LINKS
Ea kamehla: 2000 (1ms)

HO JOALOKA_LETSA
PID: 0xD451

E beha bolelele ba nako e phahameng bakeng sa boemo bo nepahetseng ba servo.
FUMANA Romela: PDL=0
Amohela: PDL=2 (Lentswe le 1 RIGHT_ADJUST_TIME)

SET Romela: PDL=2 (Lentswe le 1 RIGHT_ADJUST_TIME)
Amohela: PDL=0

LEFT_ADJUST_TIME
201 - 6000

Funktion
WERT: x 0,5µs = Impulszeit RECHTS
Ea kamehla: 4000 (2ms)

Hlahisa Fektheri bocha

Pele o etsa reset ea fektheri, bala mehato eohle ka hloko

Ho reset the DMX-Servo-Control 2 ho boemo ba pelehi tsoela pele ka tsela e latelang:

Tima sesebelisoa (Tlosa motlakase!)

Beha aterese ea 1 ho isa ho 10 ho ON
Bulela sesebelisoa (Hokela phepelo ea motlakase!)
Hona joale, LED e bonesa 20x ka hare ho hoo e ka bang ka. 3 metsotsoana
 Ha lebone la LED le ntse le benya, seta switch 10 ho tima

Reset ea fektheri e se e entsoe
 Joale, LED e benya ka nomoro ea ketsahalo ea 4
Tima sesebelisoa (Tlosa motlakase le phepelo ea USB!)
Hona joale sesebelisoa se ka sebelisoa.

Haeba fektheri e 'ngoe e hlokahala, mokhoa ona o ka phetoa.

Litekanyo

CE-Conformity
Kopano ena (boto) e laoloa ke microprocessor mme e sebelisa maqhubu a phahameng. Bakeng sa ho boloka thepa ea mojule mabapi le ho lumellana ha CE, hoa hlokahala ho kenya ntlo ea tšepe e koetsoeng ho latela taelo ea EMC 2014/30/EU.

Ho lahla
Lihlahisoa tsa elektronike le tsa elektroniki ha lia lokela ho lahleloa litšila tsa ka tlung. Lahla sehlahisoa qetellong ea bophelo ba ts'ebeletso ho latela melao e sebetsang ea molao. Lintlha mabapi le sena li ka fumanoa k'hamphaning ea lehae ea hau ea ho lahlela lithōle

Tlhokomediso
Sesebelisoa sena ha se ntho ea ho bapala. Boloka moo bana ba ka se fihleleng teng. Batsoali ba ikarabella bakeng sa tšenyo e bakiloeng ke ho se hlokomele bana ba bona.

Litlhaloso tsa Kotsi
U rekile sehlahisoa sa tekheniki. Ho ipapisitsoe le theknoloji e fumanehang ka ho fetesisa, likotsi tse latelang ha lia lokela ho qheleloa ka thoko:

Kotsi ea ho hloleha:
Sesebelisoa se ka theoha ka mokhoa o sa fellang kapa ka ho feletseng ka nako leha e le efe ntle le temoso. Ho fokotsa monyetla oa ho hloleha hoa hlokahala ho theha sistimi e sa sebetseng.

Kotsi ea ho qala:
Bakeng sa ho kenngoa ha boto, boto e tlameha ho kopanngoa le ho fetoloa ho likarolo tse tsoang linaheng tse ling ho ea ka lipampiri tsa lisebelisoa. Mosebetsi ona o ka etsoa feela ke basebetsi ba tšoanelehang, ba balang pampiri e feletseng ea lisebelisoa le ho e utloisisa.

Kotsi ea ts'ebetso:
Phetoho kapa ts'ebetso tlas'a maemo a ikhethileng a litsamaiso / likarolo tse kentsoeng, hammoho le liphoso tse patiloeng li ka baka ho senyeha ha nako e ntse e tsamaea.

Kotsi ea ho sebelisa hampe:
Tšebeliso efe kapa efe e sa tloaelehang e ka baka likotsi tse ke keng tsa lekanngoa 'me ha ea lumelloa.

Tlhokomediso: Ha e lumelloe ho sebelisa sesebelisoa ts'ebetsong, moo polokeho ea batho e itšetlehileng ka sesebelisoa sena.

DMX4ALL GmbH
Reiterweg 2A
D-44869 Bochum
Jeremane

Liphetoho tsa ho qetela: 20.10.2021

© Copyright DMX4ALL GmbH
Litokelo tsohle tsa polokelo. Ha ho karolo ea bukana ena e ka hlahisoang hape ka mokhoa ofe kapa ofe (fotokopi, khatello, microfilm kapa ka mokhoa o mong) ntle le tumello e ngotsoeng kapa ea sebetsoa, ea atisoa kapa ea phatlalatsoa ka lisebelisoa tsa elektroniki.

Lintlha tsohle tse ka har'a bukana ena li hlophisitsoe ka hloko e kholo le ka mor'a tsebo e ntle ka ho fetisisa. Leha ho le joalo liphoso ha lia lokela ho qheleloa ka thoko eseng ka botlalo. Ka lebaka lena ke ipona ke tlameha ho bontša hore nke ke ka nka lengolo la tiisetso kapa boikarabelo ba molao kapa ho khomarela liphello, tse fokotsang / khutlela ho data e fosahetseng. Tokomane ena ha e na litšobotsi tse tiisitsoeng. Tataiso le litšobotsi li ka fetoloa ka nako efe kapa efe ntle le phatlalatso e fetileng

Litokomane / Lisebelisoa

DMX4ALL DMX Servo Control 2 RDM Interface Pixel LED Controller [pdf] Bukana ea Mosebelisi
DMX Servo Control 2 RDM Interface Pixel LED Controller, DMX Servo, Control 2 RDM Interface Pixel LED Controller, Interface Pixel LED Controller, Pixel LED Controller, LED Controller, Controller

Litšupiso

Bukana ea Mosebelisi

Tlhaloso