DMX4ALL DMX Servo Control 2 RDM Interface Pixel LED Controller ntuziaka onye ọrụ

Maka nchekwa nke gị, biko gụọ akwụkwọ ntuziaka onye ọrụ na nke ọma tupu echichi.

Nkọwa

Emebere DMX-Servo-Control 2 maka ijikwa servos abụọ site na DMX.

Servos abụọ
DMX Servo Control 2 nwere ọdụ ụgbọ mmiri abụọ. Enwere ike ịchịkwa nke ọ bụla site na otu ọwa DMX.

Enwere ike iji Servos nwere 5V ruo 12V DC
The ọkọnọ voltage nke DMX-Servo-Control 2 dị n'etiti 5V na 12V. Servos nwere ọkọnọ voltage n'ime oke a nwere ike jikọọ ozugbo.

Mgbama njikwa Servo nwere ike idozi
Njikwa na-apụta site na obosara usu enwere ike idozi.

Akwụkwọ data

Ịnye ọkụ: 5-12V DC 50mA enweghị servo ejikọrọ
Usoro: DMX512 RDM
Servo-Voltage: 5-12V DC (dakọtara na ọkọnọ voltage)
Ọrụ-Ike: max. 3A na nchikota nke abụọ servos
DMX-Ọwa: Ọwa 2
Njikọ: 1x screw terminal / 2pin 1x screw terminal / 3pin 2x pin nkụnye eji isi mee RM2,54 / 3pin
Akụkụ: 30mm x 67mm

Ọdịnaya

• 1 x DMX-Servo-Control 2
• 1x ngwa ngwa German na bekee

Njikọ

Ntị :
A naghị anabata DMX-Servo-Control 2 maka ngwa ndị nwere mkpa nchekwa dị mkpa ma ọ bụ nke ọnọdụ dị ize ndụ nwere ike ime!

LED-Ngosipụta

Igwe ọkụ agbakwunyere bụ ngosipụta multifunction.

N'oge ọnọdụ ọrụ nkịtị, ọkụ LED na-enwu na-adịgide adịgide. N'okwu a, ngwaọrụ ahụ na-arụ ọrụ.

Ọzọkwa, LED na-egosi ọnọdụ dị ugbu a. N'okwu a, LED na-enwu na obere oghere ma na-efunahụ ogologo oge.

Ọnụọgụ ọkụ ndị na-egbuke egbuke hà nhata nọmba mmemme:

DMX-Na-agwa okwu

A na-agbanwe adreesị mmalite site na DIP-Switchs.

Mgbanwe 1 nwere valency 20 (= 1), gbanwee 2 na valency 21 (= 2) na ihe ndị ọzọ ruo switch9 na valency 28 (= 256).

Nchikota nke mgba ọkụ na-egosi ON hà nhata na adreesị mmalite.

Enwere ike idozi adreesị mmalite DMX site na oke RDM DMX_START ADDRESS. Maka ịrụ ọrụ RDM, a ga-edozirịrị ọkụ ọkụ niile ka ọ bụrụ gbanyụọ!
Gbanwee adreesị

Gbanwee adreesị

Mgbama njikwa Servo

Ihe mgbaàmà a na-ezigara na Servo nwere ihe dị elu na nke dị ala. Ogologo oge pulse dị mkpa maka Servo.

Dị ka ọ na-adịkarị, mkpali a dị n'etiti 1ms na 2ms, nke bụkwa ụkpụrụ ntọala maka DMX-Servo-Control 2. Ndị a bụ njedebe njedebe nke Servos ebe ọ na-ejedebe na nhazi. Ogologo pulse nke 1.5ms ga-abụ ọnọdụ etiti Servo.

Gbanwee akara njikwa Servo

Dị ka Servo ejiri mee ihe ọ nwere ike ịbụ advantageous imeghari oge mkpali. Enwere ike ịtọ oge kacha nta maka ọnọdụ aka ekpe n'ime oke 0,1-2,5ms. Oge kachasị maka ọnọdụ ziri ezi ga-abụrịrị oge kacha nta ma nwee ike ịbụ 2,54ms kacha.

Biko gaa n'ihu dị ka ndị a maka ntọala:

• Gbanwuo DMX-Servo-Control
• Tọọ DIP-Switch 9 na 10 gbanyụrụ
• Tọọ DIP-Switch 10 na ON
• Tọọ site na DIP-Switched 1-8 nke kacha nta
• Tọọ DIP-Switch 9 na ON
• Tọọ site na DIP-Switched 1-8 oge kacha
• Tọọ DIP- Gbanyụọ 10
• Ikanam ọkụ 4x dị ka nkwenye na echekwara ntọala
• Tọọ site na DIP-Switchs 1-9 adreesị mmalite DMX

Nhazi oge na-ewere ọnọdụ na DMX-adreesị site na DIP-Switches na usoro 10µs. N'ihi ya, a na-amụba uru nke nwere 0,01ms, ya mere maka example otu uru nke 100 rụpụtara na uru nke 1ms.
Enwere ike iji paramita RDM LEFT_ADJUST na RIGHT_ADJUST iji tọọ oge pulse.

RDM

(si na ngwaike V2.1)
RDM bụ ụdị dị mkpụmkpụ maka Remeputa Dihe ojoo Mnjikwa.

Ozugbo ngwaọrụ ahụ dị n'ime sistemụ, ntọala dabere na ngwaọrụ na-apụta site na iwu RDM n'ihi UID ekenyere pụrụ iche. Ọ dịghị mkpa ịnweta ngwaọrụ ozugbo.

Ọ bụrụ na edobere adreesị mmalite DMX site na RDM, mgbanwe niile adrees dị na DMXServo-Control 2 ga-atọrịrị ka Gbanyụọ! Adreesị mmalite DMX setịpụrụ site na adreesswitches bụ mgbe niile tupu!

Ngwaọrụ a na-akwado iwu RDM ndị a:

NJ paramita	Nchọpụta Iwu	SET Iwu	Nweta Iwu	ANSI/ PID
DISC_UNIQUE_BRANCH				E1.20
DISC_MUTE				E1.20
DISC_UN_MUTE				E1.20
DEVICE_INFO				E1.20
SUPPORTED_PARAMETERS				E1.20
PARAMETER_DESCRIPTION				E1.20
SOFTWARE_VERSION_LABEL				E1.20
DMX_START_ADDRESS				E1.20
DEVICE_LABEL				E1.20
MANUFACTURER_LABEL				E1.20
DEVICE_MODEL_DESCRIPTION				E1.20
IDENTIFY_DEVICE				E1.20
AKWKWỌ_DEFAULTS				E1.20
DMX_PERSONALITY				E1.20
DMX_PERSONALITY_DESCRIPTION				E1.20
DISPLAY_LEVEL				E1.20
DMX_FAIL_MODE				E1.37

DMX-Servo-njikwa 2

NJ paramita	Iwu nchọpụta	SET Iwu	Nweta Iwu	ANSI/ PID
NỌMBA USORO N'USORO1)				PID: 0xD400
LEFT_ADJUST1)				PID: 0xD450
RIGHT_ADJUST1)				PID: 0xD451

1. Onye nrụpụta dabere n'iwu njikwa RDM (MSC - ụdịdị akọwapụtara)

Onye nrụpụta dabere n'iwu njikwa RDM:

NỌMBA USORO N'USORO
PID: 0XD400

Na-ewepụta nkọwa ederede (ASCII-Text) nke nọmba nsonazụ ngwaọrụ.
Nweta izipu: PDL=0
Nata: PDL=21 (21 Byte ASCII-Ede ederede)

LEFT_ADJUST
PID: 0XD450

Na-edozi ogologo oge dị elu maka ọnọdụ servo aka ekpe.
Nweta izipu: PDL=0
Nata: PDL=2 (1 Okwu LEFT_ADJUST_TIME)

SET zipu: PDL=2 (1 Okwu LEFT_ADJUST_TIME)
Nata: PDL=0

LEFT_ADJUSTTIME
200-5999

Funktion
WERT: x 0,5µs = Njikọ njikọ
Ebube: 2000 (1ms)

RIGHT_ADJUST
PID: 0XD451

Na-edozi ogologo oge dị elu maka ọnọdụ servo ziri ezi.
Nweta izipu: PDL=0
Nata: PDL=2 (1 Okwu RIGHT_ADJUST_TIME)

SET zipu: PDL=2 (1 Okwu RIGHT_ADJUST_TIME)
Nata: PDL=0

LEFT_ADJUST_TIME
201-6000

Funktion
WERT: x 0,5µs = Impulszeit RECHTS
Ebube: 4000 (2ms)

Ntọgharị ụlọ nrụpụta

Tupu ịme nrụpụta nrụpụta ụlọ ọrụ, gụọ usoro niile nke ọma

Iji tọgharịa ya DMX-Servo-njikwa 2 na steeti nnyefe gaa n'ihu dị ka ndị a:

• Gbanyụọ ngwaọrụ (Kwụpụ ọkụ ọkụ!)
• Tọọ mgbanwe adreesị 1 ruo 10 na ON
• Gbanwuo ngwaọrụ (Jikọọ ọkọnọ ike!)
• Ugbu a, LED na-enwu 20x n'ime ca. 3 sekọnd
   Mgbe LED na-egbu maramara, gbanye 10 ka ọ bụrụ gbanyụọ
• A na-eme nrụpụta ụlọ nrụpụta ugbu a
  Ugbu a, LED na-enwu na nọmba ihe omume 4
• Gbanyụọ ngwaọrụ (Kwụpụ ike na ọkọnọ USB!)
• Enwere ike iji ngwaọrụ ugbu a.

Ọ bụrụ na nrụpụta nrụpụta ụlọ ọrụ ọzọ dị mkpa, enwere ike ịmegharị usoro a ugboro ugboro.

Akụkụ

CE- Nkwekọrịta
A na-achịkwa mgbakọ a (boọdụ) site na microprocessor ma na-eji oge dị elu. Iji dowe akụrụngwa nke modul n'ihe gbasara nkwekọ CE, ntinye n'ime ụlọ igwe mechiri emechi dịka ntuziaka EMC 2014/30/EU siri dị.

mkpofu
Ngwa eletrọnịkị na eletrọnịkị agaghị atụba ya n'ihe mkpofu ụlọ. Tụfuo ngwaahịa ahụ na njedebe nke ndụ ọrụ ya dịka ụkpụrụ iwu siri dị. Enwere ike nweta ozi gbasara nke a n'aka ụlọ ọrụ na-ekpofu ahịhịa nke mpaghara gị

Ịdọ aka ná ntị
Ngwaọrụ a abụghị ihe egwuregwu ụmụaka. Debe ebe ụmụaka na-apụghị iru. Ndị nne na nna ga-akwụ ụgwọ maka mmebi ndị ga-esi na ya pụta site n'emeghị ihe ọ bụla maka ụmụ ha.

Ihe ize ndụ- ndetu
Ị zụrụ ngwaahịa teknụzụ. N'ikwekọ na teknụzụ kachasị mma enwere, enweghị ihe egwu ndị a:

Ihe ize ndụ ọdịda:
Ngwaọrụ nwere ike ịpụ n'akụkụ ma ọ bụ kpamkpam n'oge ọ bụla na-enweghị ịdọ aka ná ntị. Iji belata ihe gbasara nke puru omume nke ọdịda, usoro sistemu anaghị arụ ọrụ dị mkpa.

Ihe egwu mmalite:
Maka ntinye nke osisi ahụ, a ga-ejikọta osisi ahụ ma gbanwee ya na ihe ndị ọzọ dị ka akwụkwọ mpempe akwụkwọ si dị. Enwere ike ịrụ ọrụ a naanị site na ndị ọrụ ruru eru, ndị na-agụ akwụkwọ ngwaọrụ zuru ezu ma ghọta ya.

Ihe egwu arụ ọrụ:
Mgbanwe ma ọ bụ arụ ọrụ n'okpuru ọnọdụ pụrụ iche nke sistemu / akụrụngwa arụnyere nwere ike yana ntụpọ zoro ezo na-eme ka ọ daa n'ime oge ịgba ọsọ.

Ihe egwu eji eme ihe na-ezighi ezi:
Ojiji ọ bụla na-ekwekọghị ekwekọ nwere ike bute ihe egwu na-enweghị atụ na anabataghị ya.

Ịdọ aka ná ntị: A naghị ekwe ka iji ngwaọrụ na-arụ ọrụ, ebe nchekwa nke mmadụ dabere na ngwaọrụ a.

DMX4ALL GmbH
Reiterweg 2A
D-44869 Bochum
Germany

Mgbanwe ikpeazụ: 20.10.2021

© Nwebiisinka DMX4ALL GmbH
Edobere ikike niile. Enweghị akụkụ nke akwụkwọ ntuziaka a nwere ike ịmegharị n'ụdị ọ bụla (foto, nrụgide, microfilm ma ọ bụ n'usoro ọzọ) na-enweghị ikike ederede ma ọ bụ hazie ya, mụbaa ma ọ bụ gbasaa site na iji usoro eletrọnịkị.

Ejiri nlezianya kacha ukwuu hazie ozi niile dị n'akwụkwọ ntuziaka a na mgbe amachara nke ọma. Agbanyeghị, a ga-ewepụ njehie ọ bụghị kpamkpam. N'ihi nke a, a na m ahụ onwe m na-amanye igosi na m nwere ike iweghara ma ọ bụ akwụkwọ ikike ma ọ bụ ọrụ iwu ma ọ bụ ihe ọ bụla adhesion maka nsonaazụ, nke na-ebelata / laghachi na data na-ezighi ezi. Akwụkwọ a enweghị njirimara ejiri n'aka. Enwere ike ịgbanwe nduzi na njirimara n'oge ọ bụla na-enweghị ọkwa gara aga

Akwụkwọ / akụrụngwa

DMX4ALL DMX Servo Control 2 RDM Interface Pixel LED Controller [pdf] Akwụkwọ ntuziaka onye ọrụ DMX Servo Control 2 RDM Interface Pixel LED Controller, DMX Servo, Control 2 RDM Interface Pixel LED Controller, Interface Pixel LED Controller, Pixel LED Controller, LED Controller, Controller.

Ntụaka

• Akwụkwọ ntuziaka onye ọrụ