BA-RCV-BLE-EZ-BAPI Wireless Receiver uye Analog Output Modules

Product Information

Zvinotsanangurwa

• Chigadzirwa: Wireless Receiver uye Analog Output Modules
• Muenzaniso Nhamba: 50335_Wireless_BLE_Receiver_AOM
• Kugarisana: Inoshanda neinosvika makumi matatu nemaviri sensors uye 32 akasiyana mamodule

Overview
Iyo Wireless Receiver kubva kuBAPI inogamuchira masaini kubva kune isina waya sensors uye inotumira data kuAnalog Output Modules kuburikidza neRS485 ina-waya bhazi. Iwo ma module anoshandura chiratidzo kuita analog kuramba, voltage, kana relay kuonana kune controller.

Setpoint Output Module (SOM)
Iyo SOM inoshandura setpoint data kubva kune isina waya yekamuri sensor kuita kuramba kana voltage. Inopa mashanu fekitori-yakaiswa voltage uye marengenzi anodzivirira ane sarudzo yekupfuura mabasa.

Relay Output Module (RYOM)
Iyo RYOM inoshandura data kubva kune isina waya inogamuchira kuita yakasimba-state switch yekuvhara yeDDC controller. Inogona kugadzirwa seyechinguvana kana latching inobuda relay.

Mirayiridzo Yekushandiswa Kwechigadzirwa

Pairing yeSensor, Receiver, uye Output Modules

Kubatanidza Sensor kune Receiver

1. Sarudza sensor kuti ubatanidze uye isa simba kwairi.
2. Isa simba kune anogamuchira. Iyo yebhuruu LED ichavhenekera.
3. Dzvanya uye bata Bhatani reSevhisi pane inogamuchira kusvika iyo yebhuruu LED yatanga kupenya. Wobva wadzvanya Bhatani reSevhisi.

FAQs

Mangani masensa anogona kugarwa neanogamuchira?
Iyo inogamuchira inogona kugara kusvika ku32 sensors.

Wireless Receiver uye Analog Output Modules

Installation uye Operating Mirayiridzo

Overview uye Identification

Iyo Wireless Receiver kubva kuBAPI inogamuchira chiratidzo kubva kune imwe kana anopfuura isina waya sensors uye inopa iyo data kuAnalog Output Modules kuburikidza neRS485 ina-waya bhazi. Iwo ma module anoshandura chiratidzo kuita analog kuramba, voltage kana relay kuonana kune controller. Iyo inogamuchira inogona kugarisa anosvika makumi matatu nemaviri sensors uye 32 akasiyana mamodule.

RESISTANCE OUTPUT MODULE (ROM)
Inoshandura data yekushisa kubva kune inogamuchira kuita 10K-2, 10K-3, 10K-3 (11K) kana 20K thermistor curve. Iyo 10K-2 unit ine inobuda huwandu hwe35 kusvika 120ºF (1 kusvika 50ºC). Iyo 10K-3 unit ine inobuda huwandu hwe32 kusvika 120ºF (0 kusvika 50ºC). Iyo 10K-3(11K) unit ine yakabuda kubva 32 kusvika 120ºF (0 kusvika 50ºC). Iyo 20K unit ine inobuda huwandu hwe53 kusvika 120ºF (12 kusvika 50ºC). Iyo chaiyo yekubuda mhando inoratidzwa pane chigadzirwa label.

VOLTAGE OUTPUT MODULE (VOM)
Inoshandura tembiricha kana humidity data kubva kune inogamuchira kuita mutsara 0 kusvika 5 kana 0 kusvika 10 VDC chiratidzo. Iyo module ine sere fekitori seti tembiricha renji, uye iyo chaiyo siyana inoratidzwa pane chigadzirwa label. Mavara acho ndeaya: 50 kusvika 90ºF (10 kusvika 32°C), 55 kusvika 85°F (13
kusvika 30 ° C), 60 kusvika 80 ° F (15 kusvika 27 ° C), 65 kusvika 80 ° F (18 kusvika 27 ° C), 45 kusvika 96 ° F (7 kusvika 35 ° C), -20 kusvika 120 ° F (-29 kusvika 49 ° C), 32 kusvika 185 ° F -0 ° 85 kusvika 40 ° F uye 140 ° F -40 ° 60 kusvika XNUMX. (-XNUMX kusvika XNUMX°C).
Iyo module ine maviri humidity renji ye0 kusvika 100% kana 35 kusvika 70% RH uye iyo chaiyo siyana inoratidzwa pane iyo label.

THE SETPOINT OUTPUT MODULE (SOM)
Inoshandura iyo setpoint data kubva kune isina waya yekamuri sensor kuita yekupikisa kana voltage. Pane shanu fekitori set voltage uye renji dzinopikisa, imwe neimwe iine sarudzo yekupfuura basa. The voltage siyana 0 kusvika 5V, 3.7 kusvika 0.85V, 4.2 kusvika 1.2V, 0 kusvika 10V uye 2 kusvika 10V. Iyo inodzivirira inosiyana ndeye 0 kusvika 10KΩ, 0 kusvika 20KΩ, 4.75K kusvika 24.75KΩ, 6.19K kusvika 26.19KΩ, 7.87K kusvika 27.87KΩ. Iyo chaiyo siyana inoratidzwa pane chigadzirwa label.

RELAY OUTPUT MODULE (RYOM)
Inoshandura iyo data kubva kune isina waya inogamuchira kuita yakasimba mamiriro switch yekuvhara yeDDC controller. Iyo RYOM ndeye mutengi-yakagadziriswa kwechinguvana kana latching inobuda relay. Inogona kudzidziswa kune akasiyana BLE isina waya ma sensors akadai seyepamusoro paBAPI-Stat "Quantum" kamuri sensor, iyo magineti gonhi switch paBAPI-Stat "Quantum Slim" kana kubuda kwemvura inodonha detector.

Pairing yeSensor, Receiver uye Analog Output Modules

Iyo yekumisikidza inoda kuti sensor yega yega isina waya inopetwa kune yayo yakabatana inogamuchira uyezve kune yayo yakabatana yekubuda module kana ma module. Iyo pairing maitiro ari nyore pane bhenji rekuyedza ine sensor, inogamuchira uye inobuda modules mukati meruoko kusvika kune mumwe nemumwe. Ita shuwa yekuisa yakasarudzika chiratidzo chechiratidzo pane sensor uye inosanganisirwa inobuda module kana mamodule mushure mekunge apetwa kune mumwe nemumwe kuti aonekwe panzvimbo yebasa. Kana inopfuura imwe shanduko ichifambiswa ne sensor (tembiricha, humidity uye setpoint semuenzaniso), imwe neimwe shanduko inoda yakaparadzana inobuda module. Multiple goho modules inogona kupetwa kune imwechete dhizaini kana ichidikanwa.

Kubatanidza sensor kune inogashira
Iwe unofanirwa kubatanidza sensor kune inogamuchira usati wabatanidza sensor kune analog inobuda module.

1. Sarudza iyo sensor yaunoda kubatanidza kune inogamuchira. Isa simba kune sensor. Ona bhuku rekushandisa kuti uwane mirairo yakazara.
2.  Isa simba kune anogamuchira. Iyo yebhuruu LED pane inogamuchira ichavhenekera uye irambe yakavhenekerwa.
3. Dzvanya uye ubatisise "Bhatani reSevhisi" pamusoro pemugamuchiri kusvikira bhuruu LED yatanga kupenya, Fig. 1: Receiver uye Output Modules Service Buttons wobva wadzvanya uye sunungura "Batanidzo Rebasa" pane sensor (Figs 2 & 3) yaunoda kubatanidza kune anogamuchira. Kana iyo LED pane inogamuchira ichidzokera kune yakasimba "On" uye yakasvibira "Sevhisi ye LED" pane sensor circuit board inobwaira nekukurumidza katatu, pairing yapera. Dzokorora maitiro aya kune ese ma sensors.

KUTANISA INOBUDZWA MODULE KUTI SENSOR
Kana iyo sensor ichinge yapetwa kune inogamuchira, unogona kubatanidza mamodule ekubuda kune iyo sensor inoshanduka.

1. Sarudza iyo inobuda module yeiyo yaunoda sensor inoshanduka uye siyana uye ibatanidze kune isina waya inogamuchira (Fig 1).
2. Dzvanya uye ubate "Bhatani reSevhisi" pamusoro peiyo module yekubuda kusvika iyo yebhuruu LED yatanga kupenya (anenge masekonzi matatu). Wobva watumira "pairing transmission sign" kune iyo inobuda module nekudzvanya nekuburitsa "Service Bhatani" pane isina waya sensor. Iyo yebhuruu LED pane inogamuchira ichapenya kamwe ichiratidza kuti kutapurirana kwakagamuchirwa; ipapo iyo yebhuruu LED pane inobuda module ichaenda yakasimba kweinenge 3 sensor uye inobuda module ikozvino yapetwa kune imwe neimwe uye icharamba yapetwa kune imwe kune imwe kuburikidza nekutsiviwa kwebhatiri kana kana simba rabviswa kubva kune waya magetsi mayuniti. Iyo inobuda module yebhuruu LED ikozvino ichapenya kamwe pese painogashira kutapurirana kubva kune sensor.

Ongorora: Iwo ma sensors asina waya anowanzo kuyera uye kufambisa akawanda mabhii, senge tembiricha uye hunyoro, kana tembiricha, humidity uye setpoint. Ese aya akasiyana anofambiswa kana sensor "Bhatani reSevhisi" rakadzvanywa. Nekudaro, yega yega Analog Output Module inogadziriswa panguva yekurongeka kune yakasarudzika chinja uye renji saka inongobatana kune iyo shanduko uye kwete mamwe.

Kukwira uye Kuwanikwa kweAntenna

Iyo antenna ine magineti base yekumisikidza. Kunyangwe iyo inogamuchira inogona kunge iri mukati mesimbi yakavharirwa, iyo antenna inofanirwa kunge iri kunze kweyakavharirwa. Panofanira kunge paine isiri-yesimbi mutsara wekuona kubva kune ese ma sensors kune antenna. Mutsara unogamuchirika wekuona unosanganisira madziro akagadzirwa nematanda, sheet rock kana plaster ine isiri-metallic lath. Mamiriro eiyo antenna (yakatwasuka kana yakatwasuka) inozokanganisa mashandiro uye inosiyana nekushandisa.
Kuisa antenna pamusoro pesimbi kunocheka kugamuchira kubva kuseri kwepamusoro. Mahwindo ane chando anogona kuvharira kugamuchira zvakare. Mutsara wehuni kana wepurasitiki wakasungirirwa padanda resirin'i inoita gomo rakakura. Iyo antenna inogona kusungirirwa kubva kune chero sirin'i inogadziriswa uchishandisa fiber kana epurasitiki twine. Usashandise waya kusungirira, uye usashandise perforated simbi tambo, inowanzonzi plumbers tepi.

Kuiswa kweReceiver uye Analog Output Modules

Iyo inogamuchira uye inobuda modules inogona kuve snaptrack, DIN Rail kana pamusoro wakaiswa. Mumwe nemumwe anogamuchira anogona kugara kusvika ku127 module. Tanga neanogamuchira kuruboshwe kuruboshwe, wobva wabatanidza zvakachengeteka imwe neimwe inobuda module kurudyi.
Sunda mumatebhu ekukwira ebhuruu kuti ukwire mu2.75” snaptrack (Fig 4). Sundidzira kunze ma tabo ekumisikidza eDIN Rail (Fig 5). Bata EZ gomo hoko pamucheto weDIN njanji (Fig 6) uye tenderera munzvimbo. Pushira kunze ma tabo ekumisikidza pamusoro pepamusoro uchishandisa masiruu mana akapihwa, imwe mune yega tab (Fig 7).
Kana ma module ako ekubuda asingakwanise kukwana mumutsara wakatwasuka nekuda kwenzvimbo shoma, wobva waisa yechipiri tambo yemamodule pamusoro kana pazasi. Batanidza waya kubva kurudyi rwekutanga tambo yemamodule kuenda kuruboshwe rwechipiri tambo yemamodule.
Kugadziridzwa uku kunoda imwe kana anopfuura Inovharika Terminal Block Connector Kits (BA/AOM-CONN) kune imwezve waya yekugumira kuruboshwe nekurudyi kweAnalog Output Modules.
Yese kit inosanganisira imwe seti ye4 ma-connectors.

Kugumisa

Iyo Wireless Receiver uye Analog Output Modules inobatika uye inogona kubatana netambo yakasungirirwa sezvakaratidzwa kurudyi. Simba reanalog inobuda modules rinopihwa neanogamuchira mune ino gadziriso. Kana ma modules achifambiswa zvakasiyana kwete kubva kune anogamuchira (sezvinoratidzwa pazasi), saka anofanira kunge aine gumi nemashanu kusvika makumi mana VDC chete. Iva nechokwadi chekuti unopa simba rakakwana kune ese maturusi ari mubhazi.

Kuwedzera iyo RS485 Network pakati peMugamuchiri neAnalog Output Modules

Iyo Analog Output Modules inogona kukwidziridzwa kusvika 4,000 tsoka kubva kune inogamuchira. Hurefu hwakazara hwetambo dzese dzakavharidzirwa, dzakamonyoroka dzinoratidzwa mumufananidzo wegumi
i4,000 tsoka (1,220 metres). Batanidza materminals pamwe chete sezvakaratidzwa muFig. 10. Kana chinhambwe kubva paunogamuchira kuenda kuboka reAnalog Output Modules chakakura kudarika 100 feet (30 metres), ipai magetsi akasiyana kana vol.tage converter (yakadai seBAPI's VC350A EZ) yeboka iro reAnalog Output Modules. Ongorora: Iyo gadziriso iri muFig 10 inoda imwe kana anopfuura Inovharika Terminal Block Kits sezvakaratidzwa pane yapfuura peji.

Receiver Switch Settings

Ese maseti sensor anodzorwa uye anogadziriswa neanogamuchira kuti aenderane nezvinodiwa zvekuisa. Izvi zvinogadziriswa kuburikidza neDIP switch pamusoro peanogamuchira. Aya ndiwo marongero eZVESE MASENSOR akapetwa kune iye anogamuchira.

Sample Rate / Kupindirana - Nguva iri pakati pekumuka kwe sensor uye inotora kuverenga. Izvo zviripo zvakakosha 30 sec, 1 min, 3 min kana 5 min.
Transmit Rate / Interval - Iyo nguva iri pakati peiyo sensor inotumira kuverenga kune anogamuchira. Hunhu huripo 1, 5, 10 kana 30 maminetsi.
Delta Temperature - Shanduko yekushisa pakati peseample uye iyo yekupedzisira kutapurirana iyo ichaita kuti sensor iwedzere nguva yekufambisa uye nekukasira kufambisa tembiricha yakachinja. Hwaro huripo i1 kana 3 °F kana °C.
Delta Humidity - Shanduko yekunyorova pakati peseample uye iyo yekupedzisira kutapurirana iyo ichaita kuti sensor iwedzere nguva yekufambisa uye nekukasira kuendesa hunyoro hwakashandurwa. Hwaro huripo i3 kana 5 %RH.

Kugadzirisazve Sensor, Receiver kana Analog Output Module

Sensors, vanogamuchira uye ma module ekubuda anoramba akabatana kune mumwe nemumwe kana simba rakakanganiswa kana mabhatiri abviswa. Kutyora zvisungo pakati pavo, iwo mayunitsi anofanirwa kusetwa patsva sezvinotsanangurwa pazasi:

• KUGADZIRA PATSVA SENSOR:
  Dzvanya uye bata "Batani reSevhisi" pane sensor kwemasekonzi makumi matatu. Pakati peaya masekonzi makumi matatu, iyo yegirini LED ichadzima kweanosvika mashanu masekonzi, yobva yapenya zvishoma nezvishoma, yobva yatanga kupenya nekukurumidza. Kana kukurumidza kupenya kunomira, kugadzirisa zvakare kwapera. Iyo sensor ikozvino inogona kupetwa kune mutsva anogamuchira. Kuti ugadzirise zvakare kune imwechete inogamuchira, unofanirwa kuseta zvakare mugamuchiri. Mamodules ekubuda ayo aimbopetwa kune sensor haidi kupetwa zvakare.
• KUITA PATSVA ZVINOBUDZWA MODULE:
  Dzvanya uye bata "Batani reSevhisi" pamusoro peiyo unit kwemasekonzi makumi matatu. Pakati peaya masekonzi makumi matatu, iyo yebhuruu LED ichadzima kwemasekonzi matatu ekutanga uye yobva yapenya kwenguva yasara. Kana kupenya kwamira, sunungura "Batani reSevhisi" uye kugadzirisazve kwapera. Iyo unit ikozvino inogona kupetwa zvakare kune sensor inoshanduka.
• KUSETA PATSVA A RECEIVER:
  Dzvanya uye bata "Batani reSevhisi" pane sensor kwemasekonzi makumi maviri. Pakati pemasekonzi makumi maviri iwayo, iyo yebhuruu LED inopenya zvishoma nezvishoma, yobva yatanga kupenya nekukurumidza. Apo kukurumidza kupenya kunomira uye kudzokera kune yakasimba yebhuruu, kugadzirisa zvakare kwapera. Iyo unit ikozvino inogona kupetwa zvakare kune isina waya sensors. Chenjero! Kugadzirisa zvakare mugamuchiri kuchatyora zvisungo pakati peanogamuchira uye ese ma sensors. Iwe uchafanirwa kuseta zvakare sensor yega yega uye wozobatanidza imwe neimwe ye sensor kune inogamuchira.

Default Status Kana Wireless Transmission ikavhiringwa

Kana iyo inobuda module isingagamuchire data kubva kune yakapihwa sensor kwemaminetsi makumi matatu neshanu, iyo yebhuruu LED pamusoro peiyo module inopenya nekukurumidza. Kana izvi zvikaitika, iyo yega Analog Output Modules ichaita seinotevera:

• Resistance Output Modules (BA/ROM) inoburitsa yakanyanya kupikisa muhuwandu hwavo hwekubuda.
• Voltage Output Modules (BA/VOM) akatemerwa tembiricha anoisa kuburitsa kwawo ku0 volts.
• Voltage Output Modules (BA/VOM) akatemerwa humidity achaisa kuburitsa kwavo kune yavo yepamusoro voltage (5 kana 10 volts).
• Setpoint Output Modules (BA/SOM) inobata kukosha kwayo kwekupedzisira nekusingaperi.

Kana kutapurirana kwagamuchirwa, ma module ekubuda anodzokera kune yakajairika kushanda mumasekonzi makumi matanhatu kana pasi.

Receiver Specifications

• Supply Power: 15 kusvika 40 VDC kana 12 kusvika 24 VAC (kubva kuhafu yewave rectified supply)
• Kushandisa Simba: 30mA @ 24 VDC, 2.75 VA @ 24 VAC
• Kugona / Chikamu: Kusvika makumi matatu nemaviri sensors uye 32 akasiyana Analog Output Modules
• Reception Distance:

Inosiyana nekushandisa*

• Frequency: 2.4 GHz (Bluetooth Low Energy)

Bus Cable Distance:

• 4,000 ft ine tambo yakavharidzirwa, yakamonyoroka

Environmental Operation Range:

• Tembiricha: 32 kusvika 140°F (0 kusvika 60°C)
• Humidity: 5 kusvika 95% RH isina-condensing
• Enclosure Material & Rating: ABS Plastiki, UL94 V-0
• Agency: RoHS / FCC: T4FSM221104 / IC: 9067A-SM221104

Ichi chishandiso chinoenderana neChikamu 15 cheFCC Mitemo. Kushanda kunoenderana nemamiriro maviri anotevera:

1. Ichi chishandiso chinogona kusakonzera kukanganisa kunokuvadza, uye
2. Muchina uyu unofanirwa kugamuchira chero kukanganisa kunowanikwa, kusanganisira kukanganisa kunogona kukonzera kushanda kusingafadzi.

Chero shanduko kana gadziridzo dzisina kutenderwa ne[kambani] dzinogona kukanganisa mushandisi simba rekushandisa mudziyo.
Mudziyo uyu unoenderana neIndustry Canada (IC) rezinesi-isina RSS mwero(s). Kushanda kunoenderana nemamiriro maviri anotevera. Mudziyo uyu unogona kusakonzera kukanganisa.
Muchina uyu unofanirwa kugamuchira chero kukanganisa, kusanganisira kukanganisa kunogona kukonzera kushanda kusingade kwemudziyo.

Analog Output Module Specifications

ALL MODULES

• Supply Power (VDC Chete): 15 kusvika 40 VDC (kubva pahafu yewave rectified supply)

Environmental Operation Range:

• Tembiricha: 32°F kusvika 140°F (0°C kusvika 60°C)
• Humidity: 5% kusvika 95% RH isina-condensing

Bus Cable Distance:

• 4,000 ft (1,220m) w/ yakadzivirirwa, yakamonyoroka tambo
• Enclosure Material & Rating: ABS Plastiki, UL94 V-0
• Sangano: RoHS

SETPOINT OUTPUT MODULE (SOM)

Kushandisa Simba:

• Resistance Models: 20 mA @ 24 VDC
• Voltage Mienzaniso: 25 mA @ 24 VDC
• Kubuda Parizvino: 2.5 mA @ 4KΩ mutoro

Yarasika Yekutaurirana Timeout:

• 35 min. (Fast Flash): Inodzokera kune yayo yekupedzisira kuraira
• Analogi Input Bias Voltage:
• 10 VDC max (Resistance Output Models chete)

Output Resolution:

• Resistance Output: 100Ω
• Voltage Kubuda: 150µV

• VOLTAGE OUTPUT MODULE (VOM)
  Kushandisa Simba: 25 mA @ 24 VDC
  Kubuda Parizvino: 2.5 mA @ 4KΩ mutoro
• Yarasika Yekutaurirana Timeout:
  35 min. (Fast Flash)
  Tembiricha inobuda inodzokera ku0 volts
  % RH inobuda inodzokera kune yakakwira (5V kana 10V)
• Kubuditsa Voltage Range:
  0 kusvika 5 kana 0 kusvika 10 VDC (fekitari calibrated)
  Kugadzirisa Kubuda: 150µV
• RESISTANCE OUTPUT MODULE (ROM)
• Kushandisa Simba:
  20 mA @ 24 VDC
  Analogi Input Bias Voltage: 10 VDC max
• Yarasika Yekutaurirana Timeout:
  35 min. (Fast Flash)
  Inodzokera kune High Resistance > 35KΩ (Low Temp)
  Temperature Output Ranges:
  10K-2 Chikamu: 35 kusvika 120ºF (1 kusvika 50ºC)
  10K-3 Chikamu: 32 kusvika 120ºF (0 kusvika 50ºC)
  10K-3(11K) Chikamu: 32 kusvika 120ºF (0 kusvika 50ºC) 20K Chikamu: 53 kusvika 120ºF (12 kusvika 50ºC)
  Kugadzirisa Kubuda: 100Ω
• RELAY OUTPUT MODULE (RYOM)
• Kushandisa Simba:
  20 mA @ 24 VDC
  Analogi Input Bias Voltage:
  10 VDC max
• Yarasika Yekutaurirana Timeout:
  35 maminetsi (Fast Flash)
  Inodzokera kumurairo wekupedzisira
  Ataure Output:
  40V (DC kana AC peak), 150 mA max.
  Off state leakage ikozvino 1 uA max.
  Panyika kuramba 15Ω max.
• Operation:
  Kanguva: 5 yechipiri nguva actuation Latching: Latching actuation

Building Automation Products, Inc., 750 North Royal Avenue, Gays Mills, WI 54631 USA
Nhare:+1-608-735-4800 • Fax+1-608-735-4804 • E-mail: sales@bapihvac.com • Web : www.bapihvac.com

Zvinyorwa / Zvishandiso

BAPI BA-RCV-BLE-EZ-BAPI Wireless Receiver uye Analog Output Modules [pdf] Installation Guide BA-RCV-BLE-EZ-BAPI, 50335_Wireless_BLE_Receiver_AOM, BA-RCV-BLE-EZ-BAPI Wireless Receiver uye Analog Output Modules, BA-RCV-BLE-EZ-BAPI, Wireless Receiver uye Analog Output Modules, Analog Output Modules, Analog Output Modules, Receiver Output Modules, Modules

References

• User Manual