Altronix Maximal1RHD Access Power Controller Manual

Zathaview

Magawo a Altronix Maximal Rack Mount Series amagawa ndikusintha mphamvu kuti apeze machitidwe owongolera ndi zida. Amasintha cholowera cha 115VAC, 50/60Hz kukhala zotuluka zisanu ndi zitatu (8) kapena khumi ndi zisanu ndi chimodzi (16) zoyendetsedwa paokha 12VDC ndi/kapena 24VDC PTC zotetezedwa. Zotulutsa zimayatsidwa ndi makina otseguka (NO) kapena otsekedwa (NC) owuma kuchokera ku Access Control System, Card Reader, Keypad, Push Button, PIR, etc. : Mag Locks, Electric Strikes, Magnetic Door Holders, ndi zina zotero. Zotulutsa zidzagwira ntchito m'njira zonse za Kulephera-Safe ndi / kapena Kulephera-Kutetezedwa. FACP Interface imathandizira Emergency Egress, Alarm Monitoring, kapena ingagwiritsidwe ntchito kuyambitsa zida zina zothandizira. Mbali yochotsa alamu yamoto imasankhidwa payekhapayekha pazotsatira zilizonse kapena zonse (onani tchati pansipa).

Tchati chosinthira Maximal Rack Mount Series:

Nambala ya AltronixModel	Power Supply 1(8 zotuluka)	Power Supply 2(8 zotuluka)	Total Linanena bungwe Panopa	PTCProtected Auto- Resettable Outputs	Maximum Current PerACM8CBR-MOutput	115VAC50/60HzInput (jambula pano)	Mayeso a Power Supply Board Input Fuse
Mtengo wapatali wa magawo 1RHD	12VDC @ 4A	N / A	4A	8	2.0A	1.9A	5A/250V
	24VDC @ 3A	N / A	3A
Mtengo wapatali wa magawo 1RD	12VDC @ 4A	N / A	4A	16	2.0A	1.9A	5A/250V
	24VDC @ 3A	N / A	3A
Mtengo wapatali wa magawo 3RHD	12VDC @ 6A	N / A	6A	8	2.0A	1.9A	3.5A/250V
	24VDC @ 6A	N / A
Mtengo wapatali wa magawo 3RD	12VDC @ 6A	N / A	6A	16	2.0A	1.9A	3.5A/250V
	24VDC @ 6A
Mtengo wapatali wa magawo 33RD	12VDC @ 6A	12VDC @ 6A	12A	16	2.0A	3.8A	3.5A/250V
	24VDC @ 6A	24VDC @ 6A
	12VDC @ 6A	24VDC @ 6A

Zofotokozera

Zolowa:

• Nthawi zambiri amatsekedwa [NC] kapena amatsegula [NO] zolowetsa zowuma (zosintha zosankhidwa).

Zotuluka:

• Zosankha payekhapayekha Mag Lock/Menyani (Kulephera-Safe, Kulephera-Kutetezedwa) zolimba zotetezedwa ndi PTC.
• Kuteteza kotentha komanso kozungulira kozungulira ndikukhazikitsanso magalimoto.

Chiyankhulo cha Alamu ya Moto:

• Kulumikizika kwa Alamu ya Moto (kulumikiza ndi kubwezeretsanso kapena kusayakira) kumasankhidwa payekhapayekha pazotsatira zilizonse.
• Kuthekera kokhazikitsiranso kutali pakuyatsa mawonekedwe a Fire Alarm Interface.
• Zosankha zolowetsa za Alamu yamoto:
  a) Nthawi zambiri amatsegula [NO] kapena amatseka [NC] zolumikizira zowuma.
  b) Kusintha kwa polarity kuchokera kudera losainira la FACP.

Zizindikiro Zowoneka:

• Ma LED amtundu wamtundu wamtundu womwe uli kutsogolo.

Kusunga Battery:

• Chaja yomangidwira yomata ma asidi a lead kapena mabatire amtundu wa gel (Pamafunikanso batire yotchinga ina).
• Malipiro apamwamba kwambiri 0.7A.
• Makinawa sinthani kuti muyime-batire pomwe AC yalephera.
• Zero voltagimatsika pomwe unit isinthira ku zosunga zobwezeretsera za batri (kulephera kwa AC).

Kuyang'anira:

• AC yalephera kuyang'anira (kulumikizana ndi fomu "C").
• Kuyang'anira batire yotsika (kulumikizana ndi fomu "C").

Zowonjezera:

• Mipiringidzo yochotsamo yokhala ndi zotsekera wononga flange.
• 3-waya chingwe chingwe.
• Kuunikira kwa master power kulumikiza chophwanyira dera ndikukhazikitsanso pamanja.
  Makulidwe a Rack (H x W x D):
  3.25" x 19.125" x 8.5"
  (82.6mm x 485.8mm x 215.9mm).

Malangizo oyika:

Zofunika: Sinthani zotuluka voltages ndi Fire Alarm Interface kasinthidwe musanayike gawo muchoyikapo.

1. Patulani pansi ndi pamwamba pa choyikapo chotchinga chassis pochotsa zomangira zisanu ndi chimodzi (6) (Rack Mechanical Drawing and Dimensions, pg. 12).
   CHENJEZO: Osagwira zitsulo zowonekera. Tsekani mphamvu yoyendera nthambi musanayike kapena kutumizira zida. Palibe magawo omwe angagwiritsidwe ntchito mkati. Bweretsani kuyika ndi kutumiza kwa ogwira ntchito oyenerera.
2. Khazikitsani voltage:
   Sankhani zomwe mukufuna kutulutsa DC voltage pokhazikitsa SW1 pa bolodi lamagetsi (mku. 1a, p. 6) pamalo oyenera (Output Voltage ndi Ma chart a Stand-by Specification Charts, p. 5). Kwa Maximal33RD seti iliyonse ya zotuluka zisanu ndi zitatu (8) zitha kukhazikitsidwa 12VDC kapena 24VDC (ex.ample: zisanu ndi zitatu (8) zotuluka @ 12VDC ndi zisanu ndi zitatu (8) zotuluka @ 24VDC).
3. Zosankha zoyambitsa mapulogalamu:
   Chipangizocho chikhoza kukonzedwa kuti chizigwira ntchito ndi njira yotseguka kapena yotsekedwa kawirikawiri kuchokera ku zipangizo zowongolera zolowera pokhazikitsa masiwichi SW3 pa bolodi la ACM8CBR-S kapena ACM16CBR-S pamalo oyenera (mkuyu 2b, p. 7); ZIMIMI pa cholowetsa chozimitsa nthawi zonse cha [NC] kapena YATSA kuti mulowetse [NO] wotsegula.
4. Zosankha zotulutsa:
   a. Zotulutsa zitha kukonzedwa kuti zikhale zonse Zolephera-Safe (mwachitsanzo, maloko a mag), zonse Zolephera-Safe (mwachitsanzo kugunda kwamagetsi) kapena kuphatikiza kulikonse pokhazikitsa ma switch ofananira OUTPUT SELECT dip (1-8) pa ACM8CBR-S. bolodi pamalo oyenera; ON for Fail Safe outputs or WOZIMU kwa zotuluka Zolephera-Safe (mkuyu 2a, pg. 7).
   Zindikirani: kasinthidwe ka linanena bungwe kudzatsatira choyambitsa cholowetsa njira
   b. Kuti mutsegule FACP Disconnect kuti mutulutse chosinthira chofananira cha FIRE ALARM INTERFACE chiyenera kukhala ON. Kuti mulepheretse FACP Chotsani masiwichi a FIRE ALARM INTERFACE (1-8) pa bolodi ya ACM8CBR-S/ACM16CBR-S iyenera kukhala OFF (Mku. 2a, p. 7).
5. Njira zolumikizirana ndi Fire Alarm Interface:
   [NC] yomwe imakhala yotsekedwa, yomwe nthawi zambiri imatsegula [NO] kulowa kapena kusintha kwa polarity kuchokera kudera la sigino la FACP kumayambitsa zotuluka zosankhidwa (Fig. 6-11, pg. 9). Kukonza Chiyankhulo cha Moto Alarm khazikitsa masiwichi a SW1 ndi SW2 pa bolodi la ACM8CBR-M kumalo oyenera (Fig. 3a ndi 3b, pg. 7) (Fire Alarm Interface Switch Settings pg. 5).
6. Kulumikiza Kwama Battery:
   Kuti mugwiritse ntchito mphamvu zolowera mabatire ndizosankha. Ngati mabatire sagwiritsidwa ntchito, kutayika kwa AC kumapangitsa kuti mphamvu yamagetsi iwonongeketage. Mabatire akagwiritsidwa ntchito, ayenera kukhala asidi wamtovu kapena mtundu wa gel. Lumikizani batire imodzi (1) ku materminals olembedwa [- BAT +] kuti mugwiritse ntchito 12VDC. Gwiritsani ntchito mabatire awiri (2) 12VDC olumikizidwa ndi mawaya angapo kuti agwire ntchito ya 24VDC (mkuyu 4b, 5b, pg. 8). Mpanda wa rack mount mpanda sukhala ndi mabatire. Pakufunika batire yapadera.
   Zindikirani: Mukamagwiritsa ntchito Maximal33RD ndikusunga batire, mabatire awiri (2) osiyana kapena mabatire ayenera kugwiritsidwa ntchito.
7. Zotsatira za Battery ndi AC Supervision:
   Lumikizani chipangizo cholozera zidziwitso choyenera kumatheminali olembedwa kuti AC Kulephera ndi Kulephera kwa Battery pa bolodi (mkuyu 4a/5a, pg. 8). Gwiritsani ntchito 22AWG mpaka 18AWG pa AC Fail ndikupereka lipoti la Low/No Battery.
8. Sonkhanitsaninso pansi ndi pamwamba pa choyikapo chotchinga pomanga zomangira zisanu ndi chimodzi (6). (Zojambula ndi Makulidwe a Rack Mechanical pg. 12).
9. Angagwirizanitse okwera m'mabokosi kwa pachiyikapo phiri Maximal kwa chiyikapo ankafuna kapena khoma unsembe (mkuyu. 12-14, p. 10).
10. Phimbani pamalo omwe mukufuna. Musatseke mpweya wolowera m'mbali.
11. Khazikitsani cholumikizira chamagetsi ku OFF malo (mkuyu 15a, pg. 12).
12. Lumikizani chingwe chamagetsi muchotengera chokhazikika cha 115VAC 50/60Hz (mkuyu 15b, p. 12).
13. Khazikitsani mphamvu yolumikizira wophwanya dera ku ON malo (mkuyu 15a, p. 12).
14. Yezerani voltage pamaso kulumikiza zipangizo. Izi zimathandiza kupewa kuwonongeka komwe kungachitike.
15. Khazikitsani cholumikizira chamagetsi ku OFF malo (mkuyu 15a, pg. 12).
16. Malumikizidwe oyambitsa:
    Lumikizani zolowetsa zolowera mwa Normally Open kapena Normally Closed kuchokera pazida zowongolera zolowera kupita kuzigawo zochotseka zolembedwa [IN1 ndi GND] kudzera pa [IN8 ndi GND] za Maximal1RHD ndi Maximal3RHD. Kwa Maximal1RD, Maximal3RD ndi Maximal33RD amalumikiza zida ku seti yachiwiri ya ma terminals olembedwa. Onetsetsani kuti zidazo zikugwirizana ndi SW3 mu sitepe 3 (Rack Mechanical Drawing and Dimensions pg. 12)
17. Zolumikizira:
    Lumikizani zidazo kuti zikhale ndi mphamvu zochotseka zolembedwa [- OUT1 +] ku [- OUT8 +] za Maximal1RHD ndi Maximal3RHD. Kwa Maximal1RD, Maximal3RD ndi Maximal33RD amalumikiza zipangizo ku seti yachiwiri ya malo otchedwa [- OUT1 +] ku [- OUT8 +] (Fig. 15c, pg. 12).
18. Njira zolumikizirana ndi Fire Alarm Interface:
    a. Lumikizani choyambitsa cha FACP kumalo ochotserako olembedwa FACP1 ndi FACP2. Mukamagwiritsa ntchito kusintha kwa polarity kuchokera pagawo lolozera la FACP, lumikizani choyipa [-] ku terminal yolembedwa kuti FACP1 ndi zabwino kutheminali yolembedwa kuti FACP2 (polarity ili mu alamu) (Rack Mechanical Drawing and Dimensions pg. 12).
    b. Pakuti latching moto Alamu mawonekedwe kulumikiza bwinobwino [NO] Bwezerani lophimba ndi zochotseka terminals chizindikiro [REST] ndi [GND] (Mkuyu. 6-11, pg. 9).
19. Khazikitsani cholumikizira chamagetsi pamalo a ON (mkuyu 15a, p. 12)

Kusamalira

Gawo liyenera kuyesedwa kamodzi pachaka kuti ligwire ntchito moyenera motere: Output Voltage Mayeso: Pansi pa katundu wabwinobwino mphamvu ya DC yotulutsa voltage iyenera kufufuzidwa ngati voliyumu yoyeneratage level (Output Voltage ndi Ma chart a Stand-by Specification Charts, p. 5).
Kuyesa kwa Battery: Pazikhalidwe zolemedwa bwino, fufuzani kuti batire yadzaza, fufuzani voltage pa malo opangira mabatire komanso pamalo opangira ma board omwe amalembedwa [- BAT +] kuonetsetsa kuti palibe kusweka kwa mawaya olumikizira batire.

Zokonda Zosintha za Alamu ya Moto:

Sinthani Malo		Zolemba za FACP
SW1	SW2
ZIZIMA	Ozimitsa	FACP Signal Circuit (Polarity Reversal).
ON	ON	Nthawi zambiri Chotsekedwa [NC] Choyambitsa Choyambitsa.
ON	ZIZIMA	Nthawi zambiri Tsegulani [NO] Choyambitsa Choyambitsa.

Kutulutsa Voltage ndi Ma chart a Stand-by Specification:

Altronix Model	Bungwe Lopereka Mphamvu	Batiri	20 min. ya Backup	4 Hr. ya Backup	24 Hr. ya Backup
Maximal1RH Maximal1R	Chithunzi cha OLS120(Onani mku. 1a, tsamba 4 la Sinthani [SW1] malo ndi malo)	12VDC/40AH*	N / A	3.5A	0.5A
		24VDC/40AH*	N / A	2.7A	0.7A
Maximal3RH Maximal3R Maximal33R	Chithunzi cha AL600ULXB(Onani mku. 1a, tsamba 4 la Sinthani [SW1] malo ndi malo)	12VDC/40AH*	N / A	5.5A	5.5A
		24VDC/40AH*	N / A	5.5A	0.7A

Kuwunika kwa LED:

LED		Mkhalidwe Wopereka Mphamvu
Chofiira (DC)	Zobiriwira (AC)
ON	ON	Mkhalidwe wabwinobwino wogwirira ntchito.
ON	ZIZIMA	Kutaya kwa AC. Batire yoyimilira yopereka mphamvu.
ZIZIMA	ON	Palibe zotulutsa za DC. Mpweya wofupika kapena kuchuluka kwa matenthedwe.
ZIZIMA	ZIZIMA	Palibe zotulutsa za DC. Kutaya kwa AC. Batire yotulutsidwa.

Kutulutsa kwa LED pa Front Panel

ON	Kutulutsa kumayambitsidwa.
Kuphethira	FACP imadula.

CHENJEZO: Kuti muchepetse chiopsezo cha moto kapena kugwedezeka kwa magetsi, musawonetse mvula kapena chinyezi. Kuyika uku kuyenera kupangidwa ndi ogwira ntchito oyenerera ndipo kuyenera kugwirizana ndi National Electrical Code ndi ma code onse akumaloko.

 Kung'anima kwa mphezi ndi chizindikiro chamutu wa muvi mkati mwa makona atatu ofanana ndi cholinga choti chidziwitse wogwiritsa ntchito za kukhalapo kwa VOL yotsekeredwa yowopsa.TAGE mkati mwa mpanda wazinthu zomwe zitha kukhala zazikulu zokwanira kupanga kugwedezeka kwamagetsi.

 Mawu ofuula omwe ali mkati mwa makona atatu ofanana amapangidwa kuti adziwitse wogwiritsa ntchito za malangizo ofunikira ogwiritsira ntchito ndi kukonza (ntchito) m'mabuku otsagana ndi chipangizocho.

Power Supply Board Output Voltage Zokonda:

Chiyankhulo cha Alamu ya Moto, Kusankha Zotuluka, ndi Mtundu Wolowetsa:

Bungwe Lopereka Mphamvu

Zithunzi za FACP Hook-Up

Nthawi zambiri Zolowetsa Zotsekedwa kuchokera ku FACP

Nthawi zambiri Open Input kuchokera ku FACP

Zosankha Zoyikira:

Kuyika kwa Rack Mount

1. Chotsani chingwe chapakati pa rack mount chassis (mkuyu 12).
2. Tsegulani m'mabulaketi (A) m'mipata yomwe ili kumanzere ndi kumanja kwa mpanda wa chipika (mkuyu 13a). Gwiritsani ntchito zomangira zitatu (3) zosalala (B) kuti muteteze mabulaketi.
3. Mosamala ikani faceplate pamwamba pa ma LED, ndipo tetezani pogwiritsa ntchito zomangira zitatu (3) za poto (C) pamwamba ndi zomangira zitatu (3) za poto (C) pansi pa faceplate (mkuyu 13b).
4. Tsegulani gawo mu malo oikirapo a EIA 19” otchinga ndi otetezedwa ndi zomangira (osaphatikizidwa) (mkuyu 13c).

Kuyika kwa Wall Mount

1. Mosamala ikani faceplate pamwamba pa ma LED, ndi chitetezo pogwiritsa ntchito zomangira zitatu (3) panmutu (C) pamwamba ndi zitatu (3) zomangira zamutu (C) pansi pa faceplate (mkuyu 14a).
2. Ikani mabulaketi okwera (A) kumbali ya kumanzere ndi kumanja kwa mpanda wa rack (Mkuyu 14b). Gwiritsani ntchito zomangira zitatu (3) zosalala (B) kuti muteteze mabulaketi okwera.
3. Ikani choyikapo ndikutetezedwa ndi zomangira (zosaphatikizidwa) (mkuyu 14c)

Zojambula za Rack Mechanical ndi Makulidwe

Zolemba / Zothandizira

Altronix Maximal1RHD Access Power Controller [pdf] Buku Logwiritsa Ntchito Maximal1RHD Access Power Controller, Maximal1RHD, Access Power Controller, Power Controller

Maumboni

• Buku Logwiritsa Ntchito