Akwụkwọ ntuziaka onye ọrụ ịnweta Altronix Maximal1RHD

gafereview

Nkeji Altronix Maximal Rack Mount Series na-ekesa ma gbanwee ike iji nweta sistemụ njikwa na ngwa. Ha na-atụgharị ntinye 115VAC, 50/60Hz ka ọ bụrụ asatọ (8) ma ọ bụ iri na isii (16) 12VDC na/ma ọ bụ 24VDC PTC na-achịkwa onwe ya. A na-arụ ọrụ mmepụta site na ndenye akpalite akọrọ (NO) ma ọ bụ nke emechiri emechi (NC) sitere na Sistemụ Njikwa Nweta, Kaadị Reader, Keypad, Button Push, PIR, wdg. nkeji ga-ebufe ike gaa na ngwaọrụ ngwaike njikwa ohere dị iche iche gụnyere gụnyere. : Mkpọchi Mag, Electric Strikes, Magnetic Door Holders, wdg. Mpụta ga-arụ ọrụ na ma Fail-Safe na/ma ọ bụ ọdịda-nchekwa ụdịdị. Interface FACP na-enyere mgbapụ ihe mberede, nlekota mkpu, ma ọ bụ enwere ike iji kpalite ngwaọrụ inyeaka ndị ọzọ. Enwere ike ịhọrọ njirimara nkwụsị ọkụ ọkụ n'otu n'otu maka ihe ọ bụla ma ọ bụ ihe niile (lee chaatị dị n'okpuru).

Chart nhazi nhazi kacha elu:

Nọmba AltronixModel	Nkwanye ike 1 (mpụta 8)	Nkwanye ike 2 (mpụta 8)	Mkpokọta mpụta ugbu a	PTCProtected Nchekwa onwe- Mpụta Ntọgharị	PerACM8CBR-Mpụta kacha ugbu a	Ntinye 115VAC50/60Hz (esere ugbu a)	Ngosipụta Fuse Board na-enye ike
Oke1RHD	12VDC @ 4A	N/A	4A	8	2.0A	1.9A	5A/250V
	24VDC @ 3A	N/A	3A
Oke1RD	12VDC @ 4A	N/A	4A	16	2.0A	1.9A	5A/250V
	24VDC @ 3A	N/A	3A
Oke3RHD	12VDC @ 6A	N/A	6A	8	2.0A	1.9A	3.5A/250V
	24VDC @ 6A	N/A
Oke3RD	12VDC @ 6A	N/A	6A	16	2.0A	1.9A	3.5A/250V
	24VDC @ 6A
Oke33RD	12VDC @ 6A	12VDC @ 6A	12A	16	2.0A	3.8A	3.5A/250V
	24VDC @ 6A	24VDC @ 6A
	12VDC @ 6A	24VDC @ 6A

Nkọwapụta

Ntinye:

• A na-emechikarị [NC] ma ọ bụ na-emepekarị ndenye kọntaktị akọrọ (gbanwee họrọ).

Nsonaazụ:

• Mkpọchi/mkpọchi Mag nke ahọpụtara n'otu n'otu (Ọdịghị-echekwa, Fail-Secure) nrụpụta ike echekwara steeti siri ike PTC.
• Nchekwa okpomọkụ na obere sekit nwere nrụpụta akpaaka.

Oti mkpu ọkụ:

• Mwepu Mkpu ọkụ (ịkpọchi na nrụpụta ma ọ bụ enweghị ike) bụ nke a na-ahọrọ n'otu n'otu maka ihe ọ bụla ma ọ bụ ihe niile.
• Ikike ntọgharị tere aka maka ijide ọnọdụ ihu igwe mkpu ọkụ.
• Nhọrọ ntinye mgbakwụnye ọkụ ọkụ:
  a) Ọ na-emepekarị [NO] ma ọ bụ na-emechikarị [NC] ntinye kọntaktị akọrọ.
  b) Ntinye ngbanwe polarity sitere na sekit mgbama FACP.

Ihe ngosi onyonyo:

• Igwe ọkụ ọnọdụ mmepụta onye ọ bụla dị n'ihu panel.

Ndabere batrị:

• Chaja arụnyere n'ime ya maka batrị ụdị ndu acid ma ọ bụ gel (A na-achọ ebe nchekwa dị iche maka batrị).
• Ọnụ ego kachasị ugbu a 0.7A.
• Gbanwee akpaaka ka batrị nọrọ na-echere mgbe AC ​​dara.
• Zero voltage dobe mgbe unit gafere na ndabere batrị (ọnọdụ ọdịda AC).

Nlekọta:

• AC dara nlekota (ụdị kọntaktị "C").
• Nlekọta batrị dị ala (ụdị kọntaktị "C").

Atụmatụ ndị ọzọ:

• Ihe mgbochi ọnụ nwere ike iwepụ nwere flange mkpọchi akpọchi.
• 3- waya eriri eriri.
• Ihe mgbawa sekit nke nna ukwu ọkụ nwere ọkụ nwere nrụgharị aka.
  Ngosi elu (H x W x D):
  3.25" x 19.125" x 8.5"
  (82.6mm x 485.8mm x 215.9mm).

Ntuziaka nwụnye:

Ihe dị mkpa: Gbanwee mmepụta voltages na Ọkụ Mkpu Interface nhazi tupu ịwụnye unit na rack.

1. Kewapụ ala na elu nke chassis rack site na iwepu skru isii (6) (Rack Mechanical Drawing and Dimensions, pg. 12).
   kpachara anya: Emetụla akụkụ ọla ndị ekpughere ekpughere aka. Mechie ike sekit alaka ụlọ ọrụ tupu ịwụnye ma ọ bụ na-arụ ọrụ. Enweghị akụkụ ndị ọrụ nwere ike ịrụ ọrụ n'ime. Tụtụ aka na nrụnye na ọrụ nye ndị ọrụ ruru eru.
2. Tọọ mmepụta voltage:
   Họrọ mmepụta DC chọrọ voltage site n'itinye SW1 na bọọdụ ọkụ ọkụ (Fig 1a, pg. 6) n'ọnọdụ kwesịrị ekwesị (Mpụta Vol.tage na Charts nkọwapụta guzoro, pg. 5). Maka Maximal33RD, enwere ike ịtọ ntọala asatọ (8) maka 12VDC ma ọ bụ 24VDC (dịka ọmụmaatụ.ample: mpụta asatọ (8) @ 12VDC na asatọ (8) mpụta @ 24VDC).
3. Nhọrọ mmemme ntinye ihe:
   Enwere ike ịhazi unit ahụ ka ọ rụọ ọrụ ma ọ bụ ntinye nke na-emeghe ma ọ bụ na-emechi emechi site na ịnweta njikwa ngwaọrụ site na ịtọ switches SW3 na ma ọ bụ ACM8CBR-S ma ọ bụ ACM16CBR-S osisi na ọnọdụ kwesịrị ekwesị (Fig 2b, pg. 7); Gbanyụọ maka ntinye akpalite [NC] mechiri emechi ma ọ bụ GBANYE maka ntinye [NO].
4. Nhọrọ mmemme:
   a. Enwere ike ịhazi nsonaazụ ya ka ọ bụrụ ihe niile Fail-Safe (ya bụ, mkpọchi mag), niile Fail-Secure (ntụgharị ọkụ eletrik) ma ọ bụ ngwakọta ọ bụla nke nke ọ bụla site na ịtọ ntọala OUTPUT SELECT dip switches (1-8) kwekọrọ na ACM8CBR-S. osisi gaa n'ọnọdụ kwesịrị ekwesị; ONYE maka Mpụta Nchekwa Ọdịda ma ọ bụ Gbanyụọ maka nsonaazụ echekwara ada ada (Fig. 2a, pg. 7).
   Mara: nhazi mmepụta ga-agbaso nhọrọ ntinye ntinye
   b. Iji mee ka mgbapu FACP maka mpụta, mgba ọkụ ọkụ ọkụ INTERFACE dabara adaba ga-adịrịrị n'ọnọdụ ON. Iji gbanyụọ FACP Kwụsịnụ ọkụ ọkụ INTERFACE itinye mgba ọkụ (1-8) na bọọdụ ACM8CBR-S/ACM16CBR-S ga-anọrịrị n'ọnọdụ gbanyụọ (Fig. 2a, pg. 7).
5. Nhọrọ nkochi anya ihu mkpu ọkụ:
   Ntinye [NC] nke emechiri emechi, nke na-emepekarị [NO] ma ọ bụ ngbanwe polarity sitere na sekit mgbaàmà FACP ga-akpalite nsonaazụ ahọpụtara (Figs. 6-11, pg. 9). Iji mee ihe omume Interface Oti mkpu ọkụ na-etinye mgba ọkụ SW1 na SW2 na bọọdụ ACM8CBR-M gaa n'ọnọdụ kwesịrị ekwesị (Fig 3a na 3b, pg. 7) (Fire Alarm Interface Switch Settings pg. 5).
6. Njikọ batrị:
   Maka ngwa njikwa ohere batrị bụ nhọrọ. Ọ bụrụ na ejighị batrị, mfu nke AC ga-ebute mfu nke mmepụta voltage. Mgbe a na-eji batrị eme ihe, ha ga-abụrịrị acid acid ma ọ bụ gel. Jikọọ otu batrị (1) na njedebe akara [- BAT +] maka ọrụ 12VDC. Jiri batrị abụọ (2) 12VDC wired na usoro maka ọrụ 24VDC (Fig 4b, 5b, pg. 8). Ogige mgbago ugwu agaghị anabata batrị. Achọrọ mkpuchi batrị dị iche.
   Mara: Mgbe ị na-eji Maximal33RD nwere nkwado batrị, enwere ike iji batrị abụọ (2) dị iche iche ma ọ bụ setịpụ batrị.
7. Battery and AC Supervision outputs:
   Jikọọ ngwaọrụ nrịbama ngosi kwesịrị ekwesị na ọdụ akara akara AC ọdịda na ọdịda batrị na bọọdụ ọkọnọ ike (Fig. 4a/5a, pg. 8). Jiri 22AWG ruo 18AWG maka ọdịda AC yana obere mkpesa batrị.
8. Tinyegharịa ala na elu nke rack mount chassis site na ijikọ skru isii (6). (Rack Mechanical Drawing and Dimensions pg 12).
9. Jikọọ ihe nrịbama na-arị elu n'elu akwa akwa Maximal maka akwa akwa ma ọ bụ nrụnye mgbidi (Fig 12-14, pg. 10).
10. Wụnye n'ebe akwa akwa achọrọ. Egbochila ikuku ikuku n'akụkụ.
11. Tọọ ihe mgbawa sekit ike na-agbanyụọ (Fig 15a, pg. 12).
12. Tinye eriri ike n'ime ebe nchekwa 115VAC 50/60Hz gbadoro ụkwụ (Fig 15b, pg. 12).
13. Tọọ ihe nbibi sekit na-akwụsị ike na ọnọdụ ON (Fig 15a, pg. 12).
14. Tule mmepụta voltage tupu jikọọ ngwaọrụ. Nke a na-enyere aka izere mmebi nwere ike ime.
15. Tọọ ihe mgbawa sekit ike na-agbanyụọ (Fig 15a, pg. 12).
16. Ntinye njikọ na-akpalite:
    Jikọọ ihe ntinye ihe na-emepe emepe ma ọ bụ na-emechikarị nke ọma site na ngwaọrụ njikwa ohere gaa na njedebe mbughari akara [IN1 na GND] site na [IN8 na GND] maka Maximal1RHD na Maximal3RHD. Maka Maximal1RD, Maximal3RD na Maximal33RD jikọọ ngwaọrụ na ọdụ nke abụọ akara. Gbaa mbọ hụ na ngwaọrụ dabara na ntọala SW3 na nzọụkwụ 3 (Rack Mechanical Drawing and Dimensions pg. 12)
17. Njikọ mmepụta:
    Jikọọ ngwaọrụ ndị a ka agbanyere na njedebe mbughari akara [- OUT1 +] na [- OUT8 +] maka Maximal1RHD na Maximal3RHD. Maka Maximal1RD, Maximal3RD na Maximal33RD jikọọ ngwaọrụ na njedebe nke abụọ akara [- OUT1 +] na [- OUT8 +] (Fig. 15c, pg. 12).
18. Nhọrọ njikọ Interface Oti mkpu:
    a. Jikọọ ntinye mkpata FACP na ọdụ mbughari akara FACP1 na FACP2. Mgbe ị na-eji ngbanwe polarity site na sekit mgbama FACP, jikọọ ihe na-adịghị mma [-] na njedebe akara FACP1 yana ihe dị mma na njedebe akara FACP2 (polarity nọ na ọnọdụ mkpu) (Rack Mechanical Drawing and Dimensions pg. 12).
    b. Maka mgbanaka oti mkpu ọkụ na-ejikọta mgba ọkụ nrụgharị nke na-emekarị [NO] gaa na njedebe mbughari akara [REST] na [GND] (Figs. 6-11, pg. 9).
19. Tọọ ihe mgbawa sekit ike na ọnọdụ ON (Fig. 15a, pg. 12)

Nlekọta

Ekwesịrị ịnwale otu nkeji opekata mpe otu ugboro n'afọ maka ọrụ kwesịrị ekwesị dịka ndị a: Mmepụta Voltage Ule: N'okpuru ọnọdụ ibu nkịtị, mmepụta DC voltage kwesịrị ịlele nke ọma voltage larịị (Mpụta Voltage na Charts nkọwapụta guzoro, pg. 5).
Nnwale batrị: N'okpuru ọnọdụ ibu nkịtị lelee na chajịrị batrị zuru oke, lelee voltaji akọwapụtaratage na ọdụ batrị yana na bọọdụ akara akara [- BAT +] iji hụ na enweghị nkwụsịtụ na wires njikọ batrị.

Ntọala mgbanwe ihu mkpu ọkụ:

Gbanwee ọnọdụ		Ntinye FACP
SW1	SW2
Gbanyụọ	Gbanyụọ	FACP mgbama sekit (Polarity Reversal).
ON	ON	Ntinye akpalite emechiri emechi.
ON	Gbanyụọ	Normally Open [NO] Trigger Input.

Mmepụta Voltage na Charts nkọwapụta kwụrụ ọtọ:

Ụdị Altronix	Board na-enye ike	Batrị	20 Min. nke ndabere	4 Hr. nke ndabere	24 Hr. nke ndabere
Maximal1RH Maximal1R	OLS120(Tụtụ aka na Fig. 1a, pg. 4 maka ọnọdụ mgbanwe [SW1] na ọnọdụ)	12VDC/40AH*	N/A	3.5A	0.5A
		24VDC/40AH*	N/A	2.7A	0.7A
Maximal3RH Maximal3R Maximal33R	AL600ULXB(Tụtụ aka na Fig. 1a, pg. 4 maka ọnọdụ mgbanwe [SW1] na ọnọdụ)	12VDC/40AH*	N/A	5.5A	5.5A
		24VDC/40AH*	N/A	5.5A	0.7A

Ihe nchọpụta LED:

Ikanam		Ọkwa inye ike
Uhie (DC)	Green (AC)
ON	ON	Ọnọdụ ọrụ nkịtị.
ON	Gbanyụọ	Mfu nke AC. Ike inye batrị guzoro ọtọ.
Gbanyụọ	ON	Enweghị mmepụta DC. Mkpirisi sekit ma ọ bụ ọnọdụ ebufe ọkụ.
Gbanyụọ	Gbanyụọ	Enweghị mmepụta DC. Mfu nke AC. Achụpụrụ batrị.

Ọkụ ọkụ na-apụta na ihu ihu

ON	A kpalitere mmepụta.
Igbu	Ịkwụsị FACP.

Ịdọ aka ná ntị: Iji belata ihe egwu nke ọkụ ma ọ bụ ujo eletrik, ekpughela akụkụ ahụ na mmiri ozuzo ma ọ bụ mmiri. Ekwesịrị ime nrụnye a site n'aka ndị ọrụ ruru eru ma kwekọọ na koodu eletriki nke mba yana koodu mpaghara niile.

 Ebumnobi ọkụ nke nwere akara isi akụ n'ime triangle nha nhata bụ iji mee ka onye ọrụ mara ọnụnọ nke VOL dị ize ndụ akpọchiri.TAGE n'ime mkpuchi ngwaahịa nke nwere ike ịdị oke zuru oke iji bụrụ ujo eletrik.

 Ebum n'obi mkpu dị n'ime triangle nha nhata bụ iji mee ka onye ọrụ mara na ọnụnọ nke ntuziaka ọrụ na mmezi (ọrụ) dị mkpa na akwụkwọ ndị na-eso ngwa ahụ.

Mpụta Board Na-enye Ike Voltage Ntọala:

Fire Alarm Interface, Output Selection, and Input Type:

Board na-enye ike

Eserese FACP nko-elu

Ntinye na-emechikarị site na FACP

Na-emepekarị ntinye sitere na FACP

Nhọrọ nkwụnye:

Nwụnye Rack Mount

1. Wepu ihe nkwado etiti n'elu chassis rack (Fig. 12).
2. Slide mounting brackets (A) into slots located on left and right side of rack enclosure (Fig. 13a). Use three (3) flat head screws (B) to secure brackets.
3. Jiri nlezianya tinye ihu ihu n'elu LEDs, ma chekwaa site na iji atọ (3) pan isi kposara (C) n'elu na atọ (3) pan isi kposara (C) na ala nke faceplate (Fig 13b).
4. Tinye nkeji n'ọkwa EIA 19” achọrọ wee chekwaa ya na skru na-ebuli elu (anaghị etinye ya) (Fig 13c).

Nwụnye mgbidi mgbidi

1. Jiri nlezianya tinye ihu ihu n'elu LEDs, ma chekwaa site na iji atọ (3) pan isi kposara (C) n'elu na atọ (3) pan isi kposara (C) na ala nke faceplate (Fig 14a).
2. Debe ihe nkwado nkwado (A) n'akụkụ aka ekpe na aka nri nke ihe mkpuchi mkpuchi (Fig 14b). Jiri skru isi atọ (3) dị larịị (B) iji chekwaa ihe nkwado mgbago.
3. Ngwunye ugwu ma chekwaa ya na skru na-ebuli elu (anaghị etinye ya) (Fig. 14c)

Ihe osise Rack Mechanical na akụkụ

Akwụkwọ / akụrụngwa

Onye njikwa ike ịnweta Altronix Maximal1RHD [pdf] Akwụkwọ ntuziaka onye ọrụ Maximal1RHD Access Power Controller, Maximal1RHD, Access Power Controller, Power Controller

Ntụaka

• Akwụkwọ ntuziaka onye ọrụ