Altronix Maximal1RHD Access Power Controller User Manual

Tshajview

Altronix Maximal Rack Mount Series units faib thiab hloov lub zog kom nkag mus rau cov tswj hwm thiab cov khoom siv ntxiv. Lawv hloov 115VAC, 50/60Hz input rau yim (8) lossis kaum rau (16) ntawm nws tus kheej tswj 12VDC thiab / lossis 24VDC PTC cov khoom tiv thaiv. Cov zis tau qhib los ntawm ib txwm qhib (NO) lossis ib txwm kaw (NC) cov lus qhia qhuav tawm los ntawm Access Control System, Card Reader, Keypad, Push Button, PIR, thiab lwm yam. Cov chav nyob yuav xa lub zog mus rau ntau yam kev nkag mus rau kev tswj hwm cov khoom siv xws li : Mag Locks, Hluav Taws Xob Strikes, Sib Nqus Qhov Rooj, thiab lwm yam. Cov khoom siv tawm yuav ua haujlwm hauv ob hom Fail-Safe thiab / lossis Fail-Secure hom. FACP Interface ua rau muaj kev kub ntxhov, kev soj ntsuam lub tswb, lossis siv tau los ua rau lwm yam khoom siv pabcuam. Lub tswb hluav taws xob disconnect feature yog ib tus kheej xaiv rau ib qho lossis tag nrho cov khoom tawm (saib daim duab hauv qab).

Maximal Rack Mount Series Configuration Chart:

Altronix Model Number	Fais fab mov 1 (8 outputs)	Fais fab mov 2 (8 outputs)	Tag nrho cov zis tam sim no	PTCProtected Auto-Resettable Outputs	Qhov siab tshaj plaws tam sim no PerACM8CBR-Moutput	115VAC 50 / 60Hz Input (tam sim no kos)	Power Supply Board Input Fuse Rating
Maximal1RHD	12VDC @ 4A	N/A	4A	8	2.0 A	1.9 A	5A / 250V
	24VDC @ 3A	N/A	3A
Maximal 1 RD	12VDC @ 4A	N/A	4A	16	2.0 A	1.9 A	5A / 250V
	24VDC @ 3A	N/A	3A
Maximal3RHD	12VDC @ 6A	N/A	6A	8	2.0 A	1.9 A	3.5A / 250V
	24VDC @ 6A	N/A
Maximal 3 RD	12VDC @ 6A	N/A	6A	16	2.0 A	1.9 A	3.5A / 250V
	24VDC @ 6A
Maximal 33 RD	12VDC @ 6A	12VDC @ 6A	12 A	16	2.0 A	3.8 A	3.5A / 250V
	24VDC @ 6A	24VDC @ 6A
	12VDC @ 6A	24VDC @ 6A

Specifications

Cov tswv yim:

• Nquag kaw [NC] lossis ib txwm qhib [NO] cov kev sib cuag qhuav (hloov xaiv tau).

Cov zis:

• Tus kheej xaiv tau Mag Lock/Strike (Fail-Safe, Fail-Secure) cov khoom hauv lub xeev PTC tiv thaiv hluav taws xob tawm.
• Thermal thiab luv Circuit Court tiv thaiv nrog nws pib pib dua.

Hluav taws kub tswb Interface:

• Hluav Taws Tswb disconnect (latching nrog reset los yog tsis-latching) yog tus kheej xaiv rau ib tug los yog tag nrho cov outputs.
• Chaw taws teeb rov pib muaj peev xwm rau latching Fire Alarm Interface hom.
• Fire Alarm disconnect input xaiv:
  a) Nquag qhib [NO] lossis ib txwm kaw [NC] kev tiv tauj qhuav.
  b) Polarity reversal input los ntawm FACP signaling circuit.

Visual Indicators:

• Tus kheej Output Status LEDs nyob rau ntawm lub vaj huam sib luag pem hauv ntej.

Roj teeb thaub qab:

• Built-in charger rau kaw cov kua qaub los yog gel hom roj teeb (Ib lub thawv cais yog xav tau rau cov roj teeb).
• Qhov siab tshaj tam sim no 0.7A.
• Tsis siv neeg hloov mus rau stand-by roj teeb thaum AC ua tsis tau.
• Zero voltage poob thaum chav hloov mus rau lub roj teeb thaub qab (AC tsis ua haujlwm).

Kev saib xyuas:

• Kev saib xyuas AC tsis ua haujlwm (daim ntawv "C" hu).
• Kev saib xyuas roj teeb tsawg (daim ntawv "C" hu rau).

Ntxiv nta:

• Tshem tau lub davhlau ya nyob twg thaiv nrog xauv ntsia hlau flange.
• 3-hlau kab cord.
• Illuminated tswv hwj chim disconnect Circuit Court breaker nrog phau ntawv pib dua.
  Rack Dimensions (H x W x D):
  3.25 "x 19.125" x 8.5"
  (82.6mm x 485.8mm x 215.9mm).

Cov lus qhia installation:

Tseem ceeb: Kho cov zis voltages thiab Fire Alarm Interface configuration ua ntej txhim kho chav nyob hauv khib.

1. Sib cais hauv qab thiab sab saum toj ntawm khib mount chassis los ntawm kev tshem tawm rau (6) screws (Rack Mechanical Drawing and Dimensions, pg. 12).
   CEEB TOOM: Tsis txhob kov cov hlau raug. Kaw ceg hluav taws xob hluav taws xob ua ntej kev teeb tsa lossis kev pabcuam khoom siv. Tsis muaj cov neeg siv khoom siv khoom siv sab hauv. Xa mus rau kev teeb tsa thiab kev pabcuam rau cov neeg ua haujlwm tsim nyog.
2. Teem tso zis voltage:
   Xaiv qhov xav tau DC tso zis voltage los ntawm kev teeb tsa SW1 ntawm lub rooj tsav khoom fais fab (daim duab 1a, pg. 6) rau qhov tsim nyog (Tshaj Tawm Voltage thiab Stand-by Specification Charts, pg. 5). Rau Maximal33RD txhua pawg ntawm yim (8) tso zis tuaj yeem teeb tsa rau 12VDC lossis 24VDC (ex.ample: yim (8) outputs @ 12VDC thiab yim (8) outputs @ 24VDC).
3. Input trigger programming xaiv:
   Chav tsev tuaj yeem tsim los ua haujlwm nrog ib txwm qhib lossis ib txwm kaw cov tswv yim los ntawm kev nkag mus tswj cov khoom siv los ntawm kev teeb tsa cov keyboards SW3 ntawm tog twg los ACM8CBR-S lossis ACM16CBR-S board mus rau txoj haujlwm tsim nyog (Fig. 2b, pg. 7); OFF rau ib txwm kaw [NC] qhov kev tawm tswv yim lossis ON rau ib txwm qhib [NO] tawm tswv yim.
4. Output programming xaiv:
   a. Cov zis tawm tuaj yeem raug tsim los ua txhua qhov Fail-Safe (piv txwv li mag xauv), tag nrho Fail-Secure (xws li hluav taws xob ntaus) lossis ib qho kev sib txuas ntawm txhua qhov los ntawm kev teeb tsa OUTPUT SELECT dip keyboards (1-8) ntawm ACM8CBR-S board mus rau txoj haujlwm tsim nyog; ON rau Fail Safe outputs los yog OFF rau Fail-Secure outputs (Fig. 2a, pg. 7).
   Nco tseg: cov zis configuration yuav ua raws li input trigger xaiv
   b. Txhawm rau ua kom lub FACP Disconnect rau qhov tso zis qhov sib thooj FIRE ALARM INTERFACE hloov yuav tsum nyob rau hauv ON txoj haujlwm. Txhawm rau lov tes taw FACP Disconnect lub FIRE ALARM INTERFACE dip keyboards (1-8) ntawm ACM8CBR-S/ACM16CBR-S board yuav tsum nyob rau hauv txoj hauj lwm OFF (Fig. 2a, pg. 7).
5. Hluav taws kub tswb Interface hookup xaiv:
   Ib txwm kaw [NC], ib txwm qhib [NO] input lossis polarity thim rov qab los ntawm FACP signaling circuit yuav ua rau cov khoom siv tau xaiv (Figs. 6-11, pg. 9). Txhawm rau ua qhov Fire Alarm Interface teeb dip keyboards SW1 thiab SW2 ntawm lub rooj tsav xwm ACM8CBR-M mus rau txoj haujlwm tsim nyog (Figs. 3a thiab 3b, pg. 7) (Fire Alarm Interface Switch Settings pg. 5).
6. Kev Sib Txuas Roj Teeb:
   Rau kev nkag mus tswj daim ntawv thov roj teeb yog xaiv tau. Yog tias tsis siv roj teeb, qhov poob ntawm AC yuav ua rau poob ntawm cov zis voltage. Thaum siv cov roj teeb, lawv yuav tsum yog cov hmoov lead acid lossis gel hom. Txuas ib (1) roj teeb rau lub terminals cim [– BAT +] rau 12VDC ua haujlwm. Siv ob (2) 12VDC roj teeb uas txuas nrog rau kev ua haujlwm 24VDC (Fig. 4b, 5b, pg. 8). Rack mount enclosure yuav tsis haum cov roj teeb. Yuav tsum muaj ib lub roj teeb cais.
   Nco tseg: Thaum siv Maximal33RD nrog roj teeb thaub qab, ob (2) cov roj teeb cais lossis cov roj teeb yuav tsum tau siv.
7. Roj teeb thiab AC Supervision outputs:
   Txuas lub cuab yeej ceeb toom tsim nyog rau lub davhlau ya nyob twg uas cim AC Fail thiab Roj Teeb Fail ntawm lub rooj tsavxwm fais fab (s) (Fig. 4a/5a, pg. 8). Siv 22AWG rau 18AWG rau AC Fail thiab Tsawg / Tsis Muaj Roj Teeb Qhia.
8. Reassemble hauv qab thiab sab saum toj ntawm khib mount chassis los ntawm fastening rau (6) screws. (Rack Mechanical Drawing and Dimensions pg. 12).
9. Txuas mounting brackets rau lub khib mount Maximal rau qhov xav tau khib lossis phab ntsa installation (Fig. 12-14, pg. 10).
10. Mount rau hauv qhov chaw khib nyiab uas xav tau. Tsis txhob thaiv cov cua vents.
11. Teem lub hwj chim disconnect Circuit Court breaker mus rau OFF txoj hauj lwm (Fig. 15a, pg. 12).
12. Txuas lub hwj chim qaum rau hauv av 115VAC 50/60Hz receptacle (Fig. 15b, pg. 12).
13. Teem lub hwj chim disconnect Circuit Court breaker mus rau ON txoj hauj lwm (Fig. 15a, pg. 12).
14. Ntsuas cov zis voltage ua ntej txuas cov khoom siv. Qhov no yuav pab kom tsis txhob muaj kev puas tsuaj.
15. Teem lub hwj chim disconnect Circuit Court breaker mus rau OFF txoj hauj lwm (Fig. 15a, pg. 12).
16. Input trigger kev sib txuas:
    Txuas qhov Nquag Qhib lossis Nquag Kaw cov lus qhia tawm los ntawm cov khoom siv tswj kev nkag mus rau cov khoom siv tshem tawm tau cim [IN1 thiab GND] mus txog [IN8 thiab GND] rau Maximal1RHD thiab Maximal3RHD. Rau Maximal1RD, Maximal3RD thiab Maximal33RD txuas cov cuab yeej mus rau qhov thib ob txheej ntawm cov khoom siv cim. Xyuas kom tseeb tias cov cuab yeej phim qhov chaw ntawm SW3 hauv kauj ruam 3 (Rack Mechanical Drawing and Dimensions pg. 12)
17. Cov khoom sib txuas:
    Txuas cov khoom siv kom muaj zog rau cov khoom siv tshem tawm tau cim [– OUT1 +] rau [– OUT8 +] rau Maximal1RHD thiab Maximal3RHD. Rau Maximal1RD, Maximal3RD thiab Maximal33RD txuas cov khoom siv mus rau qhov thib ob ntawm cov khoom siv uas cim [– OUT1 +] rau [– OUT8 +] (Fig. 15c, pg. 12).
18. Fire Alarm Interface xaiv kev sib txuas:
    a. Txuas lub FACP cov tswv yim tawm tswv yim rau cov terminals tshem tau cim FACP1 thiab FACP2. Thaum siv cov polarity thim rov qab los ntawm FACP signaling circuit, txuas qhov tsis zoo [–] mus rau lub davhlau ya nyob twg cim FACP1 thiab qhov zoo rau lub davhlau ya nyob twg cim FACP2 (polarity yog nyob rau hauv lub tswb) (Rack Mechanical Drawing thiab Dimensions pg. 12).
    b. Rau lub latching hluav taws kub tswb interface txuas ib txwm [NO] pib dua hloov mus rau qhov tshem tau cov terminals cim [REST] thiab [GND] (Figs. 6-11, pg. 9).
19. Teem lub hwj chim disconnect Circuit Court breaker rau ON txoj hauj lwm (Fig. 15a, pg. 12)

Kev tu

Chav tsev yuav tsum tau sim tsawg kawg ib xyoos ib zaug rau kev ua haujlwm kom raug raws li hauv qab no: Cov zis Voltage Test: Nyob rau hauv ib txwm load tej yam kev mob lub DC tso zis voltage yuav tsum tau kuaj xyuas kom raug voltage theem (Tshaj Tawm Voltage thiab Stand-by Specification Charts, pg. 5).
Roj teeb Test: Nyob rau hauv ib txwm load tej yam kev mob xyuas tias lub roj teeb yog tag nrho them, xyuas cov teev voltage ntawm lub roj teeb terminals thiab ntawm lub rooj tsav xwm terminals cim [– BAT +] kom ntseeg tau tias tsis muaj qhov tawg hauv cov roj teeb txuas.

Fire Alarm Interface Hloov Chaw:

Hloov chaw		FACP Input
SIB 1	SIB 2
OFF	Of	FACP Signal Circuit (Polarity Reversal).
ON	ON	Nquag Kaw [NC] Cov Lus Qhia Tawm.
ON	OFF	Nquag Qhib [NO] Cov Lus Qhia Tawm.

Tso zis Voltage thiab Stand-by Specification Charts:

Altronix Qauv	Power Supply Board	Roj teeb	20 Min. ntawm thaub qab	4 Hr. ntawm thaub qab	24 Hr. ntawm thaub qab
Maximal1RH Maximal1R	OS 120(Saib daim duab 1a, pg. 4 rau Hloov [SW1] qhov chaw thiab txoj hauj lwm)	12VDC / 40AH *	N/A	3.5 A	0.5 A
		24VDC / 40AH *	N/A	2.7 A	0.7 A
Maximal3RH Maximal3R Maximal33R	AL600 ULXB(Saib daim duab 1a, pg. 4 rau Hloov [SW1] qhov chaw thiab txoj hauj lwm)	12VDC / 40AH *	N/A	5.5 A	5.5 A
		24VDC / 40AH *	N/A	5.5 A	0.7 A

LED Diagnostics:

LED		Kev Siv Hluav Taws Xob
Liab (DC)	Ntsuab (AC)
ON	ON	Kev ua haujlwm zoo li qub.
ON	OFF	Poob AC. Stand-by roj teeb muab lub zog.
OFF	ON	Tsis muaj DC tso zis. Short circuit lossis thermal overload mob.
OFF	OFF	Tsis muaj DC tso zis. Poob AC. Roj teeb tawm.

Output LEDs rau pem hauv ntej vaj huam sib luag

ON	Cov zis yog triggered.
Ntsais	FACP disconnect.

CEEB TOOM: Txhawm rau txo qhov kev pheej hmoo ntawm hluav taws kub lossis hluav taws xob poob siab, tsis txhob tso lub tsev los nag lossis dej noo. Qhov kev teeb tsa no yuav tsum tau ua los ntawm cov neeg ua haujlwm tsim nyog thiab yuav tsum ua raws li National Electrical Code thiab tag nrho cov cai hauv zos.

 Lub teeb nyem nrog lub cim xub thawj nyob rau hauv daim duab peb sab sib npaug yog tsim los ceeb toom rau tus neeg siv kom pom qhov muaj qhov thaiv qhov phom sij VOLTAGE nyob rau hauv cov khoom ntim khoom uas tej zaum yuav muaj qhov loj txaus los ua ib qho hluav taws xob poob siab.

 Lub ntsiab lus exclamation nyob rau hauv ib daim duab peb sab sib npaug yog tsim los ceeb toom rau tus neeg siv kom pom qhov tseem ceeb ntawm kev khiav hauj lwm thiab kev saib xyuas (kev pabcuam) cov lus qhia hauv cov ntaub ntawv nrog cov khoom siv.

Power Supply Board Output Voltage Chaw:

Hluav Taws Tswb Interface, Kev Xaiv Tso Tawm, thiab Hom Khoom Siv:

Power Supply Board

FACP Hook-Up Diagrams

Nquag kaw cov tswv yim los ntawm FACP

Nquag Qhib cov tswv yim los ntawm FACP

Mounting Options:

Rack Mount Installation

1. Tshem tawm qhov chaw nruab nrab ntawm khib mount chassis (Daim duab 12).
2. Swb mounting brackets (A) rau hauv cov qhov nyob rau sab laug thiab sab xis ntawm khib khib (Fig. 13a). Siv peb (3) lub taub hau taub hau (B) kom ruaj ntseg brackets.
3. Ua tib zoo tso lub ntsej muag rau ntawm LEDs, thiab ruaj ntseg siv peb (3) lub taub hau lub taub hau (C) rau saum thiab peb (3) lub taub hau taub hau (C) rau hauv qab ntawm lub ntsej muag (Fig. 13b).
4. Swb chav nyob rau hauv qhov xav tau EIA 19 "rack txoj hauj lwm thiab ruaj ntseg nrog mounting screws (tsis suav nrog) (Daim duab 13c).

Phab ntsa Mount Installation

1. Ua tib zoo tso lub ntsej muag rau ntawm LEDs, thiab ruaj ntseg siv peb (3) lub taub hau lub taub hau (C) rau saum thiab peb (3) lub taub hau taub hau (C) rau hauv qab ntawm lub ntsej muag (Fig. 14a).
2. Muab mounting brackets (A) mus rau sab laug thiab sab xis ntawm khib khib (Fig. 14b). Siv peb (3) lub taub hau taub hau (B) kom ruaj ntseg mounting brackets.
3. Mount khib thiab ruaj ntseg nrog mounting screws (tsis suav nrog) (Fig. 14c)

Khib Mechanical Drawing thiab Dimensions

Cov ntaub ntawv / Cov ntaub ntawv

Altronix Maximal1RHD Access Power Controller [ua pdf] Tus neeg siv phau ntawv Maximal1RHD Access Power Controller, Maximal1RHD, Access Power Controller, Fais Fab Tswj Xyuas

Cov ntaub ntawv

• Cov neeg siv phau ntawv