P1、P2、P3、P4、P5

DIM/CT/RGB/RGBW/RGBCW LED Kontrollur

• Small size and light weight. The housing is made from V0 flame retardant
• PC materials from SAMSUNG/COVESTRO.
• Il-funzjoni ta 'dimming soft-on u fade-in ittejjeb il-kumdità viżwali tiegħek.
• 2.4GHz wireless signal , eliminating the need for signal wiring.
• 1-5 channel constant voltagĦruġ.
• Kontroll DIM, CT, RGB, RGBW, RGBCW dawl.
• Aħdem ma 'serje MINI RF 2.4GHz remot.
• P3, P4 and P5 have 9 built-in dynamic modes.
• One controller can be paired up with 10 remotes .
• Issinkronizza l-effetti dinamiċi bejn il-kontrolluri fl-istess grupp/żona.

Speċifikazzjonijiet Tekniċi

Mudell	P1	P2	P3	P4	P5
Sinjal ta 'Input	RF2.4GHz
Input Voltage	12-48V =
Ħruġ Voltage	12-48V
Kanali	1CH	2 CH	3 CH	4 CH	5 CH
Irrisettja Swiċċ	Iva	Iva	Iva	Nru	Nru
Kurrent tat-Tagħbija	Max. 11A	Max. 12A	Max. 15A	Max. 15A	Max. 15A
Qawwa tat-Tagħbija	132W@12V 240W@24V 288W@36V 384W@48V	144W@12V 240W@24V 288W@36V 384W@48V	180W@12V 360W@24V 432W@36V 432W@48V	180W@12V 288W@24V 360W@36V 480W@48V	180W@12V 360W@24V 450W@36V 600W@48V
Compatible Remote Contro Models	Single-zone: M1A/M1B Multi-zone: M1C/M1D Programmable: M9	Żona waħda: M1A/M1B/M2A/M2B Żona multipla: M1C/M1D/M2C/M2D Programmabbli: M9	Single-zone: m1A/M113/m2A/m2B1 M4A/M4B Multi-zone: M1C/M1D/M2C/M2D/ M4C/M4D Programmabbli: M9	Single-zone: m1A/m113/M2A/m2B1 M4A/M4B Multi-zone: M1C/M1D/M2C/M2D/ M4C/M4D Programmabbli: M9	Single-zone: M1A/M1B/m2A/M2B/ M4A/m4B/M5A/M5B Multi-zone: M1C/M1D/M2C/M2D/ M4C/M4D/M5C/M5D Programmable: M9
Protezzjoni	Protezzjoni minn short circuit, protezzjoni minn temperatura żejda, protezzjoni minn kurrent żejjed, u protezzjoni għall-prevenzjoni ta' konnessjoni inversa
Temp tax-Xogħol.	-25°C – 50°C
Dimensjoni	L91 xW37xH21(mm)
Daqs tal-Pakkett	L94xW39xH22 (mm)
Piż (GW)	46g

Daqs tal-Prodott

Unità: mm

Deskrizzjoni tat-Terminal

Dijagramma tal-Wiring

Meta P1 ikun imqabbad mal-istrixxa tad-dawl li tista' titbaxxaMeta P2 ikun imqabbad mal-istrixxa tad-dawl li tista' titbaxxaMeta P2 ikun imqabbad mal-istrixxa tad-dawl tat-temperatura tal-kulurMeta P3 ikun imqabbad mal-istrixxa tad-dawl li tista' titbaxxaMeta P3 ikun imqabbad mal-istrixxa tad-dawl tat-temperatura tal-kulurMeta P3 ikun imqabbad mal-istrixxa tad-dawl RGB

Nota: The control type of PUSH DIM will switch according to the type of the remote control.
Meta P4 ikun imqabbad mal-istrixxa tad-dawl li tista' titbaxxa

Meta P4 ikun imqabbad mal-istrixxa tad-dawl tat-temperatura tal-kulur

Meta P4 ikun imqabbad mal-istrixxa tad-dawl RGB

Meta P4 ikun imqabbad mal-istrixxa tad-dawl RGBW

Meta P5 ikun imqabbad mal-istrixxa tad-dawl li tista' titbaxxa

Meta P5 ikun imqabbad mal-istrixxa tad-dawl tat-temperatura tal-kulur

Meta P5 ikun imqabbad mal-istrixxa tad-dawl RGB

Meta P5 ikun imqabbad mal-istrixxa tad-dawl RGBW

Meta P5 ikun imqabbad mal-istrixxa tad-dawl RGBCW

Pajjar il-bogħod

Imqabbad ir-remote billi tuża l-buttuna

1. Short press the ID learning button on the controller and the indicator light flashes. Please complete the following steps within 10 seconds.
2. Pair the MINI series remote:
   Single-zone MINI remote: Long press the ON/OFF button until the controller’s indicator light flashes fast.
   Multi-zone MINI remote: Long press zone button until the controller’s indicator light flashes fast.
3. When the load light of the controller flashes slowly and then stays on constantly, the learning is successful.

Ikkonnettja r-remote billi tixgħel il-kontrollur

1. Power off the controller first.
2. Pair the MINI series remote:
   Single-zone MINI remote: Long press the ON/OFF button and power on the controller at the same time until the controller’s indicator light flashes fast.
   Multi-zone MINI remote: Long press zone button and power on the controller at the same time until the controller’s indicator light flashes fast.
3. When the load light of the controller flashes slowly and then stays on constantly, the learning is successful.

Nota: A controller can be paired with a maximum of 10 remotes. Pairing more than 10 remotes will automatically delete the earliest remote ID codes.

Neħħi l-konnettur tar-remote

Neħħi l-konnettur tar-remote billi tuża l-buttuna:

1. Delete all remote parings
   Long press the ID learning button on the controller for 10 seconds, and then short press it for 6 times. When controller’s indicator light flashes and then stays on, pairing removal is successful.
2. Ħassar tqabbil remot wieħed
   Single-zone Mini: Press and hold the ID learning key of the controller for 5 seconds. Within 10 seconds, press the on/off key three times briefly. When the load light flashes slowly and then stays on constantly, the code clearing is successful.
   Multi-zone Mini: Press and hold the ID learning key of the controller for 5 seconds. Within 10 seconds, press the zone key three times briefly. When the load light flashes slowly and then stays on constantly, the code clearing is successful.

Neħħi l-akkoppjar tar-remote billi tixgħel il-kontrollur

Ħassar tqabbil remot wieħed
Single-zone Mini: Power on the controller for 2 seconds, then power it off for 2 seconds, and power it on again. Press the on/off key three times briefly within 3 seconds. When the load light flashes slowly and then stays on constantly, the code clearing is successful.
Multi-zone Mini: Power on the controller for 2 seconds, then power it off for 2 seconds, and power it on again. Press the zone key three times briefly within 3 seconds. When the load light flashes slowly and then stays on constantly, the code clearing is successful.

Prekawzjonijiet għall-Installazzjoni

Please do not stack the products. The distance between two products should be ≥15cm so as not to aect heat dissipation and the lifespan of the products.Please do not place the products on the . The distance between the product and the should be ≥100cm so as to avoid signal interference.Jekk jogħġbok tpoġġix il-prodotti ħdejn żona kbira ta 'oġġetti tal-metall (bħal soqfa ta' stud tal-metall). Id-distanza bejn il-prodott u l-oġġett tal-metall għandha tkun ≥15cm sabiex tevita interferenza tas-sinjal.                        Jekk jogħġbok tinstallax il-prodotti fuq travi jew ħdejn il-kantunieri. Id-distanza bejn il-prodott u r-raġġ jew il-kantuniera għandha tkun ≥15cm sabiex tiġi evitata interferenza tas-sinjal.

Attenzjonijiet

• L-installazzjoni u l-ikkummissjonar tal-prodott għandhom isiru minn professjonist kwalifikat.
• Prodotti LTECH huma u mhux lightningproof mhux waterproof (mudelli speċjali ħlief). Jekk jogħġbok evita x-xemx u x-xita. Meta tkun installata barra, jekk jogħġbok kun żgur li huma mmuntati f'kompartiment li ma jgħaddix ilma minnu jew f'żona mgħammra b'apparat ta 'protezzjoni mis-sajjetti.
• Dissipazzjoni tajba tas-sħana se testendi l-ħajja tal-prodott. Jekk jogħġbok installa l-prodott f'ambjent b'ventilazzjoni tajba.
• During installation, avoid being close to large-area metallic objects or stacking the devices, so as to prevent signal interference from affecting the usage.
• Avoid installing in thunderstorm-prone areas, areas with strong magnetic fields, and high-voltage oqsma.
• Meta tinstalla dan il-prodott, jekk jogħġbok evita li tkun qrib żona kbira ta 'oġġetti tal-metall jew tistivahom biex tevita interferenza tas-sinjal.
• Jekk jogħġbok iċċekkja jekk il-vol tax-xogħoltage użat jikkonforma mar-rekwiżiti tal-parametri tal-prodott.
• Before you power on the product, please make sure all the wiring is correct in case of incorrect connection that may cause a short circuit and damage the components, or trigger a accident.
• Jekk isseħħ xi ħsara, jekk jogħġbok tippruvax tirranġa l-prodott waħdek. Jekk għandek xi mistoqsija, jekk jogħġbok ikkuntattja lill-fornitur.
• Dan il-manwal huwa soġġett għal bidliet mingħajr avviż ieħor. Il-funzjonijiet tal-prodott jiddependu fuq l-oġġetti. Jekk jogħġbok tħossok liberu li tikkuntattja lid-distributuri uffiċjali tagħna jekk għandek xi mistoqsija.

Nota: The temperature within the installation area should be within the working temperature range of the products. Please do not install products inside LED es to avoid temperature exceeding the working temperature that may aect the product lifetime.

Ftehim ta 'Garanzija

Perjodi ta' garanzija mid-data tal-kunsinna: 5 snin.
Servizzi ta' tiswija jew sostituzzjoni b'xejn għal problemi ta' kwalità huma pprovduti fi ħdan perjodi ta' garanzija.
Esklużjonijiet tal-garanzija hawn taħt:

• Lil hinn mill-perjodi ta' garanzija.
• Kwalunkwe ħsara artifiċjali kkawżata minn voltage, tagħbija żejda, jew operazzjonijiet mhux xierqa.
• Prodotti bi ħsara fiżika severa.
• Ħsara kkawżata minn diżastri naturali u force majeure.
• It-tikketti tal-garanzija u l-barcodes ġew imħassra.
• L-ebda kuntratt iffirmat minn LTECH.

1. Tiswija jew sostituzzjoni pprovduta hija l-uniku rimedju għall-klijenti. LTECH mhix responsabbli għal kwalunkwe ħsara inċidentali jew konsegwenzjali sakemm ma tkunx fi ħdan il-liġi.
2. LTECH għandha d-dritt li temenda jew taġġusta t-termini ta 'din il-garanzija, u r-rilaxx bil-miktub għandu jipprevali.

ZHUHAI LTECH TEKNOLOĠIJA, LTD.
Add: No. 183 , Shui’an 1st Road, Xiangzhou
District, 519060 Zhuhai City
IR-REPUBBLIKA TAL-POPLU TAĊ-ĊINA
Websit: www.ltech-led.com

Dokumenti / Riżorsi

Kontrollur LED LTECH P1 RGBCW [pdfManwal tas-Sid P1, Kontrollur LED RGBCW P1, Kontrollur LED RGBCW, Kontrollur LED, Kontrollur

Referenzi

• Manwal għall-Utent