P1、P2、P3、P4、P5

Rianadair DIM / CT / RGB / RGBW / RGBCW LED

• Small size and light weight. The housing is made from V0 flame retardant
• PC materials from SAMSUNG/COVESTRO.
• Bidh gnìomh lasachaidh bog agus seargach a’ neartachadh do chomhfhurtachd lèirsinneach.
• 2.4GHz wireless signal , eliminating the need for signal wiring.
• 1-5 channel constant voltage toradh.
• Smachd air solas DIM, CT, RGB, RGBW, RGBCW.
• Obraich le sreath MINI RF 2.4GHz iomallach.
• P3, P4 and P5 have 9 built-in dynamic modes.
• One controller can be paired up with 10 remotes .
• Sioncronaich buaidhean fiùghantach eadar luchd-riaghlaidh san aon bhuidheann/sòn.

Sònrachaidhean Teicnigeach

Modail	P1	P2	P3	P4	P5
Comharra cuir a-steach	RF2.4GHz
Input Voltage	12-48V =
Toradh Voltage	12-48V
Sianalan	1CH	2 CH	3 CH	4 CH	5 CH
Ath-shuidheachadh Switch	Tha	Tha	Tha	Chan eil	Chan eil
Luchdaich a-nuas an-dràsta	Max. 11A	Max. 12A	Max. 15A	Max. 15A	Max. 15A
Cumhachd luchdachadh	132W@12V 240W@24V 288W@36V 384W@48V	144W@12V 240W@24V 288W@36V 384W@48V	180W@12V 360W@24V 432W@36V 432W@48V	180W@12V 288W@24V 360W@36V 480W@48V	180W@12V 360W@24V 450W@36V 600W@48V
Compatible Remote Contro Models	Single-zone: M1A/M1B Multi-zone: M1C/M1D Programmable: M9	Aon-chrios: M1A/M1B/M2A/M2B Ioma-chrios: M1C/M1D/M2C/M2D Prògramaichte: M9	Single-zone: m1A/M113/m2A/m2B1 M4A/M4B Multi-zone: M1C/M1D/M2C/M2D/ M4C/M4D Prògramaichte: M9	Single-zone: m1A/m113/M2A/m2B1 M4A/M4B Multi-zone: M1C/M1D/M2C/M2D/ M4C/M4D Prògramaichte: M9	Single-zone: M1A/M1B/m2A/M2B/ M4A/m4B/M5A/M5B Multi-zone: M1C/M1D/M2C/M2D/ M4C/M4D/M5C/M5D Programmable: M9
Dìon	Dìon cuairt ghoirid, dìon cus teòthachd, dìon cus gnàthach, agus dìon casg ceangail cùil
Teòthachd Obrach.	-25 ° C - 50 ° C
Tomhas	L91 xW37xH21(mm)
Meud pacaid	L94xW39xH22(mm)
Cuideam (GW)	46g

Meud toraidh

Aonad: mm

Tuairisgeul Terminal

Wiring Diagram

Nuair a tha P1 ceangailte ris an stiall solais a ghabhas lasadhNuair a tha P2 ceangailte ris an stiall solais a ghabhas lasadhNuair a tha P2 ceangailte ris an stiall solais teòthachd dathNuair a tha P3 ceangailte ris an stiall solais a ghabhas lasadhNuair a tha P3 ceangailte ris an stiall solais teòthachd dathNuair a tha P3 ceangailte ris an stiall solais RGB

Thoir an aire: The control type of PUSH DIM will switch according to the type of the remote control.
Nuair a tha P4 ceangailte ris an stiall solais a ghabhas lasadh

Nuair a tha P4 ceangailte ris an stiall solais teòthachd dath

Nuair a tha P4 ceangailte ris an stiall solais RGB

Nuair a tha P4 ceangailte ris an stiall solais RGBW

Nuair a tha P5 ceangailte ris an stiall solais a ghabhas lasadh

Nuair a tha P5 ceangailte ris an stiall solais teòthachd dath

Nuair a tha P5 ceangailte ris an stiall solais RGB

Nuair a tha P5 ceangailte ris an stiall solais RGBW

Nuair a tha P5 ceangailte ris an stiall solais RGBCW

Pair an iomall

Paidhir an inneal iomallach le bhith a’ cleachdadh a’ phutan

1. Short press the ID learning button on the controller and the indicator light flashes. Please complete the following steps within 10 seconds.
2. Pair the MINI series remote:
   Single-zone MINI remote: Long press the ON/OFF button until the controller’s indicator light flashes fast.
   Multi-zone MINI remote: Long press zone button until the controller’s indicator light flashes fast.
3. When the load light of the controller flashes slowly and then stays on constantly, the learning is successful.

Paidhir an inneal iomallach le bhith a’ cur an rianadair air

1. Power off the controller first.
2. Pair the MINI series remote:
   Single-zone MINI remote: Long press the ON/OFF button and power on the controller at the same time until the controller’s indicator light flashes fast.
   Multi-zone MINI remote: Long press zone button and power on the controller at the same time until the controller’s indicator light flashes fast.
3. When the load light of the controller flashes slowly and then stays on constantly, the learning is successful.

Thoir an aire: A controller can be paired with a maximum of 10 remotes. Pairing more than 10 remotes will automatically delete the earliest remote ID codes.

Dì-cheangail an inneal iomallach

Dì-cheangail an inneal iomallach le bhith a’ cleachdadh a’ phutan:

1. Delete all remote parings
   Long press the ID learning button on the controller for 10 seconds, and then short press it for 6 times. When controller’s indicator light flashes and then stays on, pairing removal is successful.
2. Sguab às aon pharadh iomallach
   Single-zone Mini: Press and hold the ID learning key of the controller for 5 seconds. Within 10 seconds, press the on/off key three times briefly. When the load light flashes slowly and then stays on constantly, the code clearing is successful.
   Multi-zone Mini: Press and hold the ID learning key of the controller for 5 seconds. Within 10 seconds, press the zone key three times briefly. When the load light flashes slowly and then stays on constantly, the code clearing is successful.

Dì-cheangail an smachd iomallach le bhith ga chumhachdachadh

Sguab às aon pharadh iomallach
Single-zone Mini: Power on the controller for 2 seconds, then power it off for 2 seconds, and power it on again. Press the on/off key three times briefly within 3 seconds. When the load light flashes slowly and then stays on constantly, the code clearing is successful.
Multi-zone Mini: Power on the controller for 2 seconds, then power it off for 2 seconds, and power it on again. Press the zone key three times briefly within 3 seconds. When the load light flashes slowly and then stays on constantly, the code clearing is successful.

Ro-chùram stàlaidh

Please do not stack the products. The distance between two products should be ≥15cm so as not to aect heat dissipation and the lifespan of the products.Please do not place the products on the . The distance between the product and the should be ≥100cm so as to avoid signal interference.Feuch nach cuir thu na toraidhean faisg air raon mòr de stuthan meatailt (leithid mullaichean stud meatailt). Bu chòir an astar eadar an toradh agus an stuth meatailt a bhith ≥15cm gus casg a chuir air comharran a sheachnadh.                        Feuch nach stàlaich thu am bathar air sailean no faisg air na h-oiseanan. Bu chòir an astar eadar an toradh agus an giùlan no an oisean a bhith ≥15cm gus casg a chuir air comharran.

An aire

• Bu chòir stàladh agus coimiseanadh toraidh a dhèanamh le proifeasanta teisteanasach.
• Tha agus chan eil toraidhean LTECH dìon-uisge neo-dhìonach (modalan sònraichte air an cumail a-mach). Feuch an seachainn thu a’ ghrian agus an uisge. Nuair a thèid a chuir a-steach a-muigh, dèan cinnteach gu bheil iad air an cur suas ann an cuairteachadh dìon-uisge no ann an àite le innealan dìon dealanach.
• Leudaichidh deagh sgaoileadh teas beatha an toraidh. Feuch an stàlaich thu an toradh ann an àrainneachd le deagh fhionnarachadh.
• During installation, avoid being close to large-area metallic objects or stacking the devices, so as to prevent signal interference from affecting the usage.
• Avoid installing in thunderstorm-prone areas, areas with strong magnetic fields, and high-voltage raointean.
• Nuair a stàlaicheas tu an toradh seo, feuch nach bi thu faisg air raon mòr de stuthan meatailt no gan cruachadh gus casg a chuir air comharran.
• Feuch an dèan thu cinnteach a bheil an leabhar obrachtagTha e air a chleachdadh a rèir riatanasan paramadair an toraidh.
• Before you power on the product, please make sure all the wiring is correct in case of incorrect connection that may cause a short circuit and damage the components, or trigger a accident.
• Ma thachras locht, na feuch ris an toradh a chàradh leat fhèin. Ma tha ceist sam bith agad, cuir fios chun t-solaraiche.
• Tha an leabhar-làimhe seo fo ùmhlachd atharrachaidhean gun rabhadh a bharrachd. Tha gnìomhan toraidh an urra ris a ’bhathair. Faodaidh tu fios a chuir chun luchd-sgaoilidh oifigeil againn ma tha ceist sam bith agad.

Thoir an aire: The temperature within the installation area should be within the working temperature range of the products. Please do not install products inside LED es to avoid temperature exceeding the working temperature that may aect the product lifetime.

Aonta barantais

Ùine barantais bhon cheann-latha lìbhrigidh: 5 bliadhna.
Gheibhear seirbheisean càraidh no ath-chuir an-asgaidh airson duilgheadasan càileachd taobh a-staigh amannan barantais.
Toirmeasg barantais gu h-ìosal:

• Seachad air amannan barantais.
• Milleadh fuadain sam bith air adhbhrachadh le vol àrdtage, cus cuideim, no obrachaidhean neo-iomchaidh.
• Bathar le fìor mhilleadh corporra.
• Milleadh air adhbhrachadh le mòr-thubaistean nàdurrach agus force majeure.
• Chaidh bileagan barantais agus còdan-barra a mhilleadh.
• Cha robh cùmhnant sam bith air a shoidhnigeadh le LTECH.

1. Is e càradh no ath-nuadhachadh an aon leigheas do luchd-ceannach. Chan eil LTECH buailteach airson milleadh tuiteamach no buil sam bith mura h-eil e taobh a-staigh an lagh.
2. Tha a ’chòir aig LTECH cumhachan a’ bharantais seo atharrachadh no atharrachadh, agus bidh làmh an uachdair ann an cruth sgrìobhte.

ZHUHAI LTECH TECHNOLOGY CO., LTD.
Add: No. 183 , Shui’an 1st Road, Xiangzhou
District, 519060 Zhuhai City
POBLACHD SLUAGH SHÌNA
Weblàrach: www.ltech-led.com

Sgrìobhainnean/Goireasan

Smachdadair LED LTECH P1 RGBCW [pdfLeabhar-làimhe an t-Sealbhadair P1, Smachdadair LED RGBCW P1, Smachdadair LED RGBCW, Smachdadair LED, Smachdadair

Iomraidhean

• Leabhar-làimhe cleachdaiche