LTECH P1 RGBCW LED Controller Owner's Manual

P1、P2、P3、P4、P5

ọdịnaya zoo

1 DIM/CT/RGB/RGBW/RGBCW LED Controller

8 Akpachara anya nwụnye

9 Akwụkwọ ikike akwụkwọ ikike

10 Akwụkwọ / akụrụngwa

10.1 Ntụaka

DIM/CT/RGB/RGBW/RGBCW LED Controller

Small size and light weight. The housing is made from V0 flame retardant

PC materials from SAMSUNG/COVESTRO.
Ọrụ dị nro na nke na-agwụ ike na-eme ka nkasi obi gị dịkwuo mma.
2.4GHz wireless signal , eliminating the need for signal wiring.
1-5 channel constant voltage mmepụta.
Jikwaa DIM, CT, RGB, RGBW, ọkụ RGBCW.
Na-arụ ọrụ na MINI usoro RF 2.4GHz ime.
P3, P4 and P5 have 9 built-in dynamic modes.
One controller can be paired up with 10 remotes .

Mekọrịta mmetụta dị ike n'etiti ndị njikwa n'otu otu/mpaghara.

Nka nka

Nlereanya	P1	P2	P3	P4	P5
Nbanye Nbanye	RF2.4GHz
Ntinye Voltage	12-48V =
Mmepụta Voltage	12-48V
Ọwa	1CH	2 CH	3 CH	4 CH	5 CH
Tọgharia Mgbanwe	Ee	Ee	Ee	Mba	Mba
Ibu Ibu Ugbu a	Oke. 11A	Oke. 12A	Oke. 15A	Oke. 15A	Oke. 15A
Ibu Ike	132W@12V 240W@24V 288W@36V 384W@48V	144W@12V 240W@24V 288W@36V 384W@48V	180W@12V 360W@24V 432W@36V 432W@48V	180W@12V 288W@24V 360W@36V 480W@48V	180W@12V 360W@24V 450W@36V 600W@48V
Compatible Remote Contro Models	Single-zone: M1A/M1B Multi-zone: M1C/M1D Programmable: M9	Single-zone: M1A/M1B/M2A/M2B Multi-zone: M1C/M1D/M2C/M2D Programmable: M9	Single-zone: m1A/M113/m2A/m2B1 M4A/M4B Multi-zone: M1C/M1D/M2C/M2D/ M4C/M4D Programmable: M9	Single-zone: m1A/m113/M2A/m2B1 M4A/M4B Multi-zone: M1C/M1D/M2C/M2D/ M4C/M4D Programmable: M9	Single-zone: M1A/M1B/m2A/M2B/ M4A/m4B/M5A/M5B Multi-zone: M1C/M1D/M2C/M2D/ M4C/M4D/M5C/M5D Programmable: M9
Nchedo	Short circuit protection, over-temperature protection, over-current protection, and reverse connection prevention protection
Okpomọkụ na-arụ ọrụ.	-25°C – 50°C
Akụkụ	L91 xW37xH21(mm)
Nha ngwugwu	L94xW39xH22(mm)
Ibu(GW)	46g

Nha ngwaahịa

Nkeji: mm

Nkọwa njedebe

Eserese waya

When P1 is connected to the dimmable light stripWhen P2 is connected to the dimmable light stripWhen P2 is connected to the color temperature light stripWhen P3 is connected to the dimmable light stripWhen P3 is connected to the color temperature light stripWhen P3 is connected to the RGB light strip

Mara: The control type of PUSH DIM will switch according to the type of the remote control.
When P4 is connected to the dimmable light strip

When P4 is connected to the color temperature light strip

When P4 is connected to the RGB light strip

When P4 is connected to the RGBW light strip

When P5 is connected to the dimmable light strip

When P5 is connected to the color temperature light strip

When P5 is connected to the RGB light strip

When P5 is connected to the RGBW light strip

When P5 is connected to the RGBCW light strip

Jikọọ remote

Pair the remote by using the button

Short press the ID learning button on the controller and the indicator light flashes. Please complete the following steps within 10 seconds.
Pair the MINI series remote:
Single-zone MINI remote: Long press the ON/OFF button until the controller’s indicator light flashes fast.
Multi-zone MINI remote: Long press zone button until the controller’s indicator light flashes fast.

When the load light of the controller flashes slowly and then stays on constantly, the learning is successful.

Pair the remote by powering on the controller

Power off the controller first.
Pair the MINI series remote:
Single-zone MINI remote: Long press the ON/OFF button and power on the controller at the same time until the controller’s indicator light flashes fast.
Multi-zone MINI remote: Long press zone button and power on the controller at the same time until the controller’s indicator light flashes fast.

When the load light of the controller flashes slowly and then stays on constantly, the learning is successful.

Mara: A controller can be paired with a maximum of 10 remotes. Pairing more than 10 remotes will automatically delete the earliest remote ID codes.

Unpair the remote

Unpair the remote by using the button:

Delete all remote parings
Long press the ID learning button on the controller for 10 seconds, and then short press it for 6 times. When controller’s indicator light flashes and then stays on, pairing removal is successful.
Delete a single remote paring
Single-zone Mini: Press and hold the ID learning key of the controller for 5 seconds. Within 10 seconds, press the on/off key three times briefly. When the load light flashes slowly and then stays on constantly, the code clearing is successful.
Multi-zone Mini: Press and hold the ID learning key of the controller for 5 seconds. Within 10 seconds, press the zone key three times briefly. When the load light flashes slowly and then stays on constantly, the code clearing is successful.

Unpair the remote by powering on the controller

Delete a single remote paring
Single-zone Mini: Power on the controller for 2 seconds, then power it off for 2 seconds, and power it on again. Press the on/off key three times briefly within 3 seconds. When the load light flashes slowly and then stays on constantly, the code clearing is successful.
Multi-zone Mini: Power on the controller for 2 seconds, then power it off for 2 seconds, and power it on again. Press the zone key three times briefly within 3 seconds. When the load light flashes slowly and then stays on constantly, the code clearing is successful.

Akpachara anya nwụnye

Please do not stack the products. The distance between two products should be ≥15cm so as not to aect heat dissipation and the lifespan of the products.Please do not place the products on the . The distance between the product and the should be ≥100cm so as to avoid signal interference.Biko etinyela ngwaahịa ndị a n'akụkụ nnukwu ebe ihe igwe (dị ka uko ụlọ stud metal). Ebe dị n'etiti ngwaahịa na ihe igwe kwesịrị ịdị ≥15cm ka ịzenarị ndabichi mgbaàmà. Biko etinyela ngwaahịa ndị a n'osisi ma ọ bụ n'akụkụ akụkụ. Ebe dị n'etiti ngwaahịa na doo ma ọ bụ nkuku kwesịrị ịbụ ≥15cm ka ịzenarị ndabichi mgbaàmà.

Nlebara anya

Ekwesịrị ime ntinye na ntinye ngwaahịa site na ọkachamara ruru eru.
Ngwaahịa LTECH abụghị ọkụ anaghị egbochi mmiri (ụdị pụrụ iche ewezuga). Biko zere anyanwụ na mmiri ozuzo. Mgbe etinyere ya n'èzí, biko hụ na etinyere ha n'ebe mkpuchi mmiri ma ọ bụ n'ebe a na-eji ihe nchebe ọkụ.

Igwe ọkụ dị mma ga-agbatị ndụ ngwaahịa ahụ. Biko tinye ngwaahịa a na gburugburu ebe ikuku ikuku dị mma.
During installation, avoid being close to large-area metallic objects or stacking the devices, so as to prevent signal interference from affecting the usage.

Avoid installing in thunderstorm-prone areas, areas with strong magnetic fields, and high-voltage mpaghara.
Mgbe ị rụnyere ngwaahịa a, biko zere ịnọ nso nnukwu ebe ihe igwe ma ọ bụ ikpokọta ha ka ọ gbochie ndabichi mgbaàmà.

Biko lelee ma vol na-arụ ọrụtage ji mee ihe kwekọrọ na oke chọrọ nke ngwaahịa.
Before you power on the product, please make sure all the wiring is correct in case of incorrect connection that may cause a short circuit and damage the components, or trigger a accident.

Ọ bụrụ na mmejọ mere, biko anwala idozi ngwaahịa ahụ n'onwe gị. Ọ bụrụ na ị nwere ajụjụ ọ bụla, biko kpọtụrụ onye na-ebubata ya.
Akwụkwọ ntuziaka a nwere ike ịgbanwe na-enweghị ọkwa ọzọ. Ọrụ ngwaahịa dabere na ngwaahịa. Biko nweere onwe gị ịkpọtụrụ ndị nkesa gọọmentị anyị ma ọ bụrụ na ị nwere ajụjụ ọ bụla.

Mara: The temperature within the installation area should be within the working temperature range of the products. Please do not install products inside LED es to avoid temperature exceeding the working temperature that may aect the product lifetime.

Akwụkwọ ikike akwụkwọ ikike

Oge ikike site na ụbọchị nnyefe: afọ 5.
A na-enye nrụzi ma ọ bụ ngbanwe efu maka nsogbu dị mma n'ime oge ikike.
Mwepu akwụkwọ ikike n'okpuru:

Agafee oge ikike.
Mmebi ọ bụla artificial kpatara site na elu voltage, ibufe oke, ma ọ bụ arụmọrụ na-ezighi ezi.
Ngwaahịa nwere mmebi anụ ahụ siri ike.
Mmebi nke ọdachi ndị na-emere onwe ha na ike majeure kpatara.
Ebibiela akara akwụkwọ ikike na koodu mkpuchi.
Enweghị nkwekọrịta ọ bụla LTECH bịanyere aka na ya.

Ndozi ma ọ bụ ngbanwe enyere bụ naanị ọgwụgwọ maka ndị ahịa. LTECH agaghị akwụ ụgwọ maka mmebi ọ bụla ma ọ bụ ihe kpatara ya ma ọ bụrụ na ọ dị n'ime iwu.

LTECH nwere ikike imeghari ma ọ bụ mezie usoro nke akwụkwọ ikike a, na mwepụta n'ụdị ederede ga-emeri.

Ụlọ ọrụ ZHUHAI LTECH TECHNOLOGY CO., LTD.
Add: No. 183 , Shui’an 1st Road, Xiangzhou
District, 519060 Zhuhai City
Obodo CHINA ndị mmadụ
Websaịtị: www.ltech-led.com

Akwụkwọ / akụrụngwa

LTECH P1 RGBCW LED Controller [pdf] Akwụkwọ ntuziaka onye nwe
P1, P1 RGBCW LED Controller, RGBCW LED Controller, LED Controller, Controller

Ntụaka

Akwụkwọ ntuziaka onye ọrụ