Summit Bed Frame Hardware
MAS90: 5043-43240 | Kit Number: 7030-00453 KIT
| QTY: | DESCRIPTION: |
|---|---|
| 8 | 100MM DECORATIVE HEAD LAG BOLTS |
| 1 | 4MM ALLEN WRENCH |
| 10 | 6 X 1 1/4" PHIL FLAT PARTICLE BOARD SCREW |
| 1 | 4MM POWER DRILL DRIVER |
Visual representation of hardware: [Lag Bolt: A long, thick metal bolt with a hexagonal head and coarse threading.] [Allen Wrench: An L-shaped hexagonal metal tool.] [Phillips Flat Particle Board Screw: A screw with a flat head and Phillips drive, suitable for particle board.] [4mm Power Drill Driver: A tool for driving screws using a 4mm bit.]
Assembly Information
Assembly Time: 1 PERSON AND 30 MINUTES
Tools Required:
- 4 mm Allen Wrench (INCLUDED)
- 4 mm Allen Drill Bit (Be sure to FULLY SEAT bit into bolt head before turning)
- Phillips Head Screwdriver
*We recommend using a power driver with the drill bit if available*
BE SURE THAT LAG BOLTS ARE STARTED INTO THE HOLES ON THE FRAME RAILS DURING ASSEMBLY. DO NOT FULLY TIGHTEN UNTIL ASSEMBLY IS LOOSELY COMPLETE.
Parts List
Visual representation of the bed: [Image: Summit Full Bookcase Bed with Double 4-Drawer Storage in a dark wood finish, featuring a headboard with shelving and four drawers below.] [Image: Summit Full Bookcase Bed with Double 4-Drawer Storage in a grey wood finish, viewed from a different angle.]
- A) 8 – 100mm Decorative Head Lag Bolts
- B) 1 - Headboard Assembly
- C) 1 - Footboard Assembly
- D) 2 - 5 1/4" x 75" Mattress Rails w/Support Cleats.
- E) 3 - 3 1/2" x 38 3/4" (Twin) Individual slats
- F) 10 - 1 1/4" Wood Screws
- G) 1 – 4mm Driver for power drill
- H) 8 - Silver drawer pulls (box in drawer unit)
- I) 16 - 1 1/2" Pan head machine screws (box in drawer unit)
- J) 1 - Silver Knob (stapled to inside of Footboard Door)
- K) 1 - 3/4" Pan head machine screw (packaged with knob)
NOTE: Make sure you have all parts before beginning assembly. If you need a part, contact the dealer where you purchased your bed.
Assembly Steps
- Attach mattress rails (D), to headboard (B), and footboard (C) with eight lag bolts and tighten.
- Spread Slat roll out across bed frame from end to end. Place wood screws in 4 outside corners with slat pushed tightly up against the footboard/headboard. Place 3 loose slats into gaps in slat roll, and screw down with wood screws. See Slat installation information on following pages.
- Install pulls on drawer fronts and knob on footboard door with supplied machine screws, and slide 4Drw Underdressers into position below mattress rail on both sides of bed.
- Add the proper thickness innerspring bunk mattress. See Living Spaces for details.
Slat Installation Details
Installation of individual slats for use with Bunkie Board
(Bunkie Board sold separately) See your retailer for purchase of Bunkie Board
Diagram showing slat placement with a Bunkie Board. The diagram illustrates the bed frame with a Bunkie Board laid across it. Arrows indicate where screws are to be placed. [Slat placement diagram: Shows the bed frame with a Bunkie Board. Arrows point to screw locations.]
Installation of individual slats for use with Slat Roll
(Slat roll sold separately) See your retailer for purchase of Slat Roll
Diagram illustrating slat placement with a slat roll. The diagram shows the bed frame with a slat roll. It indicates that when using a slat roll, three individual slats should be placed evenly in the gaps and underneath the strapping before fastening. Arrows show screw locations. [Slat roll diagram: Shows the bed frame with a slat roll. Arrows indicate screw locations. Text notes that three individual slats should be placed evenly in gaps and under strapping before fastening.]
Visual representation of individual slats: [Individual Slat: A flat wooden plank.]
