Yaheetech 614955 Assembly and Care Guide

Introduction and Safety

Please read this instruction manual carefully before attempting to install.

Important Information

• Assembly requires 2 or more people. ?‍?‍?
• Estimated assembly time: 1 hour. ⏰
• Not intended for use by children. ??
• Keep away from fire or other heat sources. ?
• We recommend wearing protective gloves. ?

Assembly Tip: Use a soft pad or blanket on your floor and the product during assembly to prevent scratches and damage. ❌ (Incorrect method: assembling directly on the floor) ✔️ (Correct method: assembling on a protective surface).

Parts List

• Part A: Side Frame (x2)
• Part B: Horizontal Support Rail (x6)
• Part C: Horizontal Support Rail (x6)
• Part D: Vertical Support Beam (x2)
• Part E: Top Shelf (70cm) (x2)
• Part F: Middle/Bottom Shelf (67.5cm) (x4)
• Part G: Adjustable Feet (x6)
• Part H: Screw (x12)
• Part I: Screw (x36)
• Part J: Allen Wrench (x1)
• Part K: Wooden Dowel (x2)

Assembly Instructions

Step 1

Attach horizontal support rails (B) and (C) to the side frames (A). Ensure correct orientation of parts (B) and (C). Use screws (I) for assembly. Diagram illustrates attaching parts B and C to a frame, with a checkmark indicating correct orientation.

Step 2

Connect parts (B), (C), and (E) using screws (I). Insert wooden dowels (K) into the designated holes on part (E) before attaching to (B) and (C). Diagram shows two shelf units being assembled with parts B, C, E, and K, secured by screws I.

Step 3

Attach vertical support beams (D) to the shelf units. Use screws (H) to secure parts (E) and (F) to the vertical beams (D). During assembly, first half-tighten all screws. Fully tighten them only after all screws are set. Diagram shows vertical beams (D) attached to shelves (E) and (F) using screws (H). A close-up highlights the process of half-tightening screws.

Step 4

Attach the side frames (A) to the assembled structure. Use screws (I) to connect the side frames to the shelves (F). Diagram shows side frames (A) being attached to the main body of the unit with screws (I).

Step 5

Secure the central vertical supports (D) and shelves (E, F) using screws (H). Ensure all screws are fully tightened after the entire unit is assembled. Diagram shows the central structure being reinforced with screws (H), with a close-up showing full tightening.

Step 6

Attach the adjustable feet (G) to the bottom of the unit. Diagram shows the base of the unit with adjustable feet (G) being screwed in.

Step 7

Screw in the adjustable feet (G) to keep the table balanced. Adjust the feet until the unit is level and stable. Diagram illustrates an adjustable foot being rotated to level the unit.

Furniture Care Instructions

• Use a soft, clean cloth or sponge to gently wipe the outer surface to remove dust and dirt.
• Avoid using chemical cleaners or harsh solvents to prevent damage to the product's appearance.
• Inspect fittings (bolts, screws, nuts) every 3 months and re-tighten them every 6 months.
• Avoid direct sunlight.
• If the furniture shows structural damage or poses a safety hazard, stop using it until it is repaired.

Customer Support

If you are not entirely satisfied with your purchase, please feel free to contact us using the following steps:

1. Go to Your Orders.
2. Find your order in the list.
3. Select Problem with order.
4. Choose your topic from the list displayed.
5. Select Contact seller.

Contact Information:

• US: YAHEE TECHNOLOGIES CORP, Address: 1532 S VINEYARD AVE ONTARIO CA 91761
• UK: Monumart Limited, Address: Europa House, Europa Way, IP15DL, Ipswich.
• Germany: Yahee GmbH, Address: Höpfigheimer Straße 11, 74321 Bietigheim-Bissingen
• France: Yahee SAS, Address: 6, Place de la Madeleine, 75008 Paris.
• Italy: Yahee SRL, Address: Via Generale Gustavo Fara, 26, 20124 Milano.