Yaheetech 611942 Computer Desk

Important Information & Safety

Please read this instruction manual carefully before attempting to install.

Recommendations:

• We recommend 1 or more people to install. ?‍?‍?
• The expected assembly time is 1 hour. ⏱️
• Not intended for use by children. ??
• Keep away from fire or other heat sources. ?❌
• We recommend wearing protective gloves. ?✔️

Assembly Tip: Use a pad to avoid damage during assembly.

Diagram Description: The process of unpacking and preparing parts for assembly is illustrated. One diagram shows a red cross (❌) indicating incorrect handling of parts from the carton, while another shows a green checkmark (✔️) indicating correct handling onto a protective surface.

Parts List

Hardware:

• A: Screw (55mm) x4
• B: Screw (45mm) x4
• C: Screw (35mm) x8
• D: Screw (30mm) x4
• E: Screw (25mm) x2
• F: Screw (long) x8
• G: Screw (short) x4
• H: Caster Wheel x4
• I: Foot Pad x2
• J: Nut x8
• K: Drawer Slide Connector x2

Tools Included:

• Screwdriver
• Wrench

Assembly Instructions

Step 1: Attach Caster Wheels

Attach the four caster wheels (H) to the bottom of the left side panel (1) and the right side panel (2).

Diagram Description: Shows side panels 1 and 2 with four caster wheels (H) being attached to their bases.

Step 2: Attach Bottom Shelf

Connect the bottom shelf (3) to the side panels (1 and 2) using eight long screws (F).

Diagram Description: Shows side panels 1 and 2, bottom shelf 3, and screws F being used to join them.

Step 3: Attach Vertical Support Rods

Attach the two vertical support rods (5) to the top of the side panels (1 and 2) using four screws (A) and four nuts (J).

Diagram Description: Shows side panels 1 and 2, vertical rods 5, screws A, and nuts J being assembled at the top.

Step 4: Attach Shelf Support Brackets and Keyboard Tray Slide

Attach the two shelf support brackets (8) to the side panels using four screws (D). Then, attach the keyboard tray slide (12) to the brackets (8).

Diagram Description: Shows brackets 8 being attached to the side panels with screws D, followed by the keyboard tray slide 12 being mounted onto the brackets.

Step 5: Attach Keyboard Tray

Attach the keyboard tray (9) to the keyboard tray slide (12) using two foot pads (I) and two screws (E).

Diagram Description: Shows the keyboard tray 9 being attached to the slide 12 with screws E and foot pads I.

Step 6: Disassemble Drawer Slides

To disassemble the drawer slides (10, 11), first pull out the inner slide. Then, use a screwdriver to push down the plastic release tab and draw the inner slide away from the outer slide.

Diagram Description: Illustrates the process of separating the inner and outer parts of the drawer slides (10 and 11) by pressing a release tab with a screwdriver.

Step 7: Attach Drawer Slides to Side Panels

Attach the outer parts of the drawer slides (10 and 11) to the inside of the side panels (1 and 2) using four screws (B) and four nuts (J).

Diagram Description: Shows the outer drawer slides 10 and 11 being attached to the inner surfaces of side panels 1 and 2 with screws B and nuts J.

Step 8: Attach Main Desktop

Place the main desktop (6) onto the assembled frame and secure it using four short screws (G).

Diagram Description: Shows the main desktop 6 being placed on top of the frame and fastened with screws G.

Step 9: Attach Upper Shelf

Attach the upper shelf (7) to the vertical support rods (5) using eight screws (C).

Diagram Description: Shows the upper shelf 7 being attached to the vertical rods 5 with screws C.

Step 10: Attach Handle Bar

Attach the handle bar (13) to the front of the keyboard tray (9) using two screws (E).

Diagram Description: Shows the handle bar 13 being screwed onto the front edge of the keyboard tray 9.

Step 11: Insert Keyboard Tray

Slide the keyboard tray (9) onto its corresponding slide (12) until it clicks into place.

Diagram Description: Shows the keyboard tray 9 being inserted into the slide mechanism.

Step 12: Insert Inner Drawer Slides

Attach the inner drawer slide components (10-1 and 11-1) to the underside of the main desktop (6) and the upper shelf (7) using the drawer slide connectors (K). Then, align and insert these inner slides into the outer slides attached to the side panels.

Diagram Description: Shows the inner slide parts being attached to the desktop and upper shelf, and then being slid into the outer rails.

Step 13: Final Tightening and Check

Important: Half tighten all screws during initial assembly. After all parts are assembled, go back and fully tighten all screws. ⚠️⚙️✔️❌

Diagram Description: Two diagrams illustrate screw tightening. The first shows a hand partially tightening a screw with a checkmark (✔️) and a cross (❌) indicating incorrect partial tightening. The second shows a hand fully tightening a screw with a checkmark (✔️) and a cross (❌) indicating incorrect full tightening before the final step.

Diagram Description: Shows the fully assembled Yaheetech 611942 computer desk.

Product Care Instructions

• Use a soft, clean cloth or sponge to gently wipe the outer surface to remove dust and dirt.
• Avoid using chemical cleaners or harsh solvents to prevent damage to the product's appearance.
• Inspect fittings (bolts, screws, nuts, etc.) every 3 months and re-tighten them every 6 months.
• Avoid direct sunlight.
• If the product shows structural damage or poses a safety hazard, stop using it until it is repaired.

Support and Contact

If you are not entirely satisfied with your purchase, please feel free to contact Yaheetech customer support by following these steps:

1. Go to Your Orders.
2. Find your order in the list.
3. Select "Problem with order".
4. Choose your topic from the displayed list.
5. Select "Contact seller".

Yaheetech US Contact:
YAHEE TECHNOLOGIES CORP
Address: 1532 S VINEYARD AVE ONTARIO CA 91761

Yaheetech UK Contact:
Monumart Limited
Address: Europa House, Europa Way, IP15DL, Ipswich.