Yaheetech 593029/593035/593058 Round Folding Table
Assembly Instructions
Important Information
Assembly Recommendation: 1 or more people.
Estimated Assembly Time: 1 hour.
Safety Warnings:
- Not intended for use by children. ??
- Keep away from fire or other heat sources. ?
Recommendations:
- We recommend wearing protective gloves. ?
- Use a pad or soft surface to avoid damage during assembly.
Parts List
| Item | Description | Quantity |
|---|---|---|
| ① | Tabletop (2 halves) | 2 |
| ② | Leg | 4 |
| ③ | Crossbar | 1 |
| ④ | Crossbar | 1 |
| ⑤ | Crossbar | 1 |
| ⑥ | Crossbar | 1 |
| A | Screw | 14 |
| B | Screw | 4 |
| C | Screw | 8 |
| D | Dowel/Peg | 4 |
| E | Adjustable Foot | 4 |
| F | Bracket/Connector | 8 |
| G | Allen Key | 1 |
Assembly Steps
General Note: Half-tighten screws during initial assembly. Tighten all screws completely after the entire structure is assembled. ✔️
-
Step 1: Base Frame Assembly
Attach legs (②) to crossbars (③, ⑤) using screws (C, F). Pay attention to the correct orientation of the legs (②). Then, attach crossbars (④, ⑥) to the legs (②) using screws (A). Ensure all connections are secure but not fully tightened yet. ❌
Diagram Description: Shows the connection of legs to crossbars, highlighting the orientation of part (2) and the use of screws (C, F, A).
-
Step 2: Attaching Tabletop Halves
Insert dowels (D) into the designated holes on the base frame. Place the tabletop halves (①) onto the base frame, aligning them with the dowels. ➡️
Diagram Description: Shows dowels being inserted and tabletop halves being placed onto the assembled base.
-
Step 3: Securing the Tabletop
Secure the tabletop to the base frame using screws (E) and brackets (F). Then, use the remaining screws (A, B) to further reinforce the structure, connecting the tabletop to the base. ➡️
Diagram Description: Illustrates attaching the tabletop to the base using screws and brackets.
-
Step 4: Balancing the Table
Screw in the adjustable feet (E) at the bottom of each leg. Adjust them as needed to ensure the table is stable and balanced on your floor. ⚙️
Diagram Description: Close-up view of an adjustable foot being screwed into the leg to level the table.
Final Check: After completing all steps, ensure all screws are fully tightened. ✔️
Product Care Instructions
- Use a soft, clean cloth or sponge to gently wipe the outer surface of the product to remove dust and dirt.
- Avoid using chemical cleaners or harsh solvents to prevent damage to the product's appearance.
- Inspect the fittings (bolts, screws, nuts, etc.) every 3 months and re-tighten them every 6 months.
- Avoid direct sunlight.
If the product shows structural damage or poses a safety hazard, stop using it until it is repaired.
Contact and Manufacturer Information
If you are not entirely satisfied with your purchase, please feel free to contact customer support:
- Go to Your Orders.
- Find your order in the list.
- Select "Problem with order".
- Choose your topic from the displayed list.
- Select "Contact seller".
US Contact:
YAHEE TECHNOLOGIES CORP
Address: 1532 S VINEYARD AVE ONTARIO CA 91761
UK Contact:
Monumart Limited
Address: Europa House, Europa Way, IP15DL, Ipswich.
Manufacturer Information:
Made in PRC for Yahee GmbH
Yahee GmbH
Address: Höpfigheimer Straße 11, 74321 Bietigheim-Bissingen
Email: info@yaheetech.shop
You can also download the electronic Installation Manual from the product guides and documents section of the advertising page.
