Yaheetech 615118 Armchair

Important Information

• ? Recommended: 1 or more people to install.
• ⏱️ Estimated assembly time: 1 hour.
• ? Not intended for use by children.
• ? Keep away from fire or heat sources.
• ? Recommended: Wear protective gloves.
• ⚠️ Follow instructions and use a pad to avoid damage during assembly. [Diagram shows a person placing a box on a protective mat, with a checkmark, versus placing it directly on the floor with a cross mark.]

Parts List

Main Components:

• A: Base Frame (x1) [Diagram shows a curved metal frame.]
• B: Side Supports (x2) [Diagram shows two curved metal pieces.]
• C: Swivel Base (x1) [Diagram shows a circular metal plate with holes.]
• D: Lower Support Ring (x1) [Diagram shows a circular metal ring with legs.]
• E: Seat Cushion (x1) [Diagram shows a round, tufted cushion.]

Hardware:

• 1: Bolt (x9) [Diagram shows a bolt.]
• 2: Screw (x8) [Diagram shows a screw.]
• 3: Nut (x9) [Diagram shows a nut.]
• 4: Wrench (x1) [Diagram shows a wrench.]
• 5: Allen Key (x2) [Diagram shows an L-shaped Allen key.]
• 6: Washer (x26) [Diagram shows a washer.]

Assembly Instructions

Step 1: Assemble Base Frame

Attach the side supports (B) to the base frame (A) using 9 bolts (1), 9 nuts (3), and 18 washers (6). Half-tighten all bolts and nuts for now. [Diagram shows parts A and B being joined by bolts (1) and nuts (3) with washers (6). Close-up views illustrate half-tightening (check mark) versus over-tightening (cross mark).]

Step 2: Attach Swivel Base

Attach the swivel base (C) to the lower support ring (D) using 4 screws (2) and 4 washers (6). Half-tighten all screws. [Diagram shows part C being attached to part D using screws (2) and washers (6). A close-up view illustrates half-tightening.]

Step 3: Connect Base Structures

Connect the assembled lower support ring (D) with swivel base (C) to the main frame (A) using 4 screws (2) and 4 washers (6). Half-tighten all screws. [Diagram shows the assembled D+C unit connecting to the main frame A using screws (2) and washers (6). Another diagram shows the connection point.]

Step 4: Attach Seat Cushion

Place the seat cushion (E) onto the assembled frame. [Diagram shows part E being placed on top of the assembled structure.]

Final Tightening

After all parts are assembled, go back and fully tighten all bolts and screws. ✔️? [Diagram shows a hand fully tightening a screw.]

Product Care Instructions

To maintain the appearance and longevity of your product:

• Wipe the outer surface gently with a soft, clean cloth or sponge to remove dust and dirt.
• Avoid using chemical cleaners or harsh solvents, as they can damage the product's appearance.
• Inspect fittings (bolts, screws, nuts) every 3 months and re-tighten them every 6 months.
• Avoid direct sunlight exposure.
• If the product shows structural damage or poses a safety hazard, stop using it until repaired.

Upholstered Furniture Care:

If the product becomes stained, use a specific upholstery cleaner sprayed onto the stain. Wipe gently with a soft towel and avoid vigorous scrubbing to prevent pilling.

Customer Support

If you are not entirely satisfied with your purchase, please feel free to contact us using the following steps:

• Go to Your Orders.
• Find your order in the list.
• Select "Problem with order".
• Choose your topic from the list displayed.
• Select "Contact seller".

Contact Information:

• USA: YAHEE TECHNOLOGIES CORP, Address: 1532 S VINEYARD AVE, ONTARIO, CA 91761
• UK: Monumart Limited, Address: Europa House, Europa Way, IP15DL, Ipswich.

Manufacturer Information

Manufactured in PRC for Yahee GmbH.

Yahee GmbH, Höpfigheimer Straße 11, 74321 Bietigheim-Bissingen

Email: info@yaheetech.shop