Manuals+

XBA-USD6 Option Switch Settings

Supported bill $ 1, 5, 10, 20, 50, 100 6bills.

XBA-USD6 Option Switch Settings

FUNCTION SW1SW2SW3SW4SW5SW6SW7SW8
Reject $ 1 ON
Accept $ 1 OFF
Reject $ 5 ON
Accept $ 5 OFF
Reject $ 10 ON
Accept $ 10 OFF
Reject $ 20 ON
Accept $ 20 OFF
Reject $ 50 & 100 ON
Accept $ 50 & 100 OFF
Disable Bill Reject 4 Times
BA Stop By 30 Sec		 ON
Enable Bill Reject 4 Times
BA Stop By 30 Sec		 ON
Stack Banknote when Power-up OFF
Reject Banknote when Power-up OFF
Reserved ON
Reserved OFF

XBA-USD6 (Pulse/MDB/ICT002U/ICT104U/ICT104V) Option Switch Settings

FUNCTION SW1SW2SW3SW4SW5SW6SW7SW8
Inhibit Active HIGH ON
Inhibit Active LOW OFF
Reserved ON
Reserved OFF
Reserved ON
Reserved OFF
Pulse Mode
MDB Mode		 SCALING_FACTOR
100
Pulse Mode
ICT104V Mode		 DECIMAL PLACE OFF
2
Other Mode Connect with coin change, SCALING FACTOR 1, DECIMAL PLACE_OFF 1, Connect with ICT JPSTD Converter board
Pulse Mode
Other Mode		 1 pulse / USD 1 MDB Mode OFFOFF
2 pulse / USD 1 ICT002U Mode OFFON
4 pulse / USD 1 ICT104U Mode ONOFF
20 pulse / USD 1 ICT104V Mode ONON

★ Manufacture setting

Note: 1. After setting dip switch of the credit pulses, you should reset the bill acceptor again.

2. Calibration card is needed.

DIP Switch Location

This dip switch is located at the side of XBA. [Diagram showing the side of the XBA unit with a callout labeled (2) pointing to the DIP Switch]

Currency Assign Data

Interface BV1BV2BV3BV4BV5BV6BV7
ICT002U USD 1USD 5USD 10USD 20USD 50USD 100USD 100
ICT104U USD 1USD 5USD 10USD 20USD 50USD 100USD 100
ICT104V USD 1USD 5USD 10USD 20USD 50USD 100USD 100
Pulse USD 1USD 5USD 10USD 20USD 50USD 100USD 100
MDB USD 1USD 5USD 10USD 20USD 50USD 100USD 100

CPU Board DIP Switch Location

This dip switch is located on the CPU board. Remove the CPU board cover first. [Diagram showing the CPU board with a callout labeled (1) pointing to the DIP Switch]

PDF preview unavailable. Download the PDF instead.

XBA-USD6(Pulse+MDB US+ICT002U+ICT104U+ICT104V) Corel PDF Engine Version 17.1.0.572 CorelDRAW X7

Related Documents

Preview XBA-NZD5 Bill Acceptor: Option Switch Settings and Currency Assignment Guide
Comprehensive guide detailing the XBA-NZD5 bill acceptor's option switch configurations for various modes including Pulse, MDB, and ICT104V. Features currency assignment data for New Zealand Dollars (NZD) and switch location information.
Preview XBA-KHR8 Bill Acceptor DIP Switch Settings and Configuration Guide
Detailed guide to configuring the XBA-KHR8 bill acceptor series from International Currency Technologies Corporation, covering DIP switch settings for Pulse, MDB, ICT002U, ICT104U, and ICT104V interfaces, along with currency assignment data.
Preview XBA-JMD6 Bill Acceptor Option Switch Settings and Configuration Guide
Detailed guide to configuring the XBA-JMD6 bill acceptor, including option switch settings for various currencies (JMD) and communication protocols (Pulse, MDB, ICT). Covers currency assignment, setup notes, and DIP switch locations.
Preview XBA-TWD4 Bill Acceptor Option Switch Settings and Configuration Guide
Comprehensive guide detailing the XBA-TWD4 bill acceptor's DIP switch settings for various operating modes including Pulse, MDB, ICT104U, and ICT104V. Includes currency assignment data and configuration notes.
Preview XBA-KZT6 Bill Acceptor Option Switch Settings and Currency Assignment
Detailed configuration guide for the XBA-KZT6 bill acceptor, covering option switch settings for Pulse, MDB, ICT104U, and ICT104V interfaces, along with currency assignment data.
Preview XBA-TEY12 Bill Acceptor Option Switch Settings and Configuration
Detailed guide to option switch settings for the International Currency Technologies (ICT) XBA-TEY12 bill acceptor, covering TRY and EUR currencies, Pulse, MDB, and ICT104U/ICT104V modes. Includes currency assignment data and setup notes.
Preview XBA-RUB6 Bill Acceptor: Option Switch Settings and Configuration
Guide to XBA-RUB6 bill acceptor option switch settings for Pulse, MDB, ICT104U, and ICT104V interfaces, including currency assignment data by International Currency Technologies Corporation.
Preview XBA-REN11 Bill Acceptor Switch Settings and Configuration Guide
A comprehensive guide detailing the dip switch settings for the XBA-REN11 bill acceptor, covering various protocols like Pulse, MDB, ICT104U, and ICT104V, along with currency assignment data.