XBA-TWD4 Bill Acceptor Option Switch Settings and Configuration

Supported Bills

The XBA-TWD4 supports the following bill denominations: $100, $200, $500, $1000, across 4 bill types.

XBA-TWD4 Option Switch Settings

FUNCTION	SW1	SW2	SW3	SW4	SW5	SW6	SW7	SW8
Reject TWD 100	ON
Accept TWD 100		OFF
Reject TWD 200			ON
Accept TWD 200				OFF
Reject TWD 500					ON
Accept TWD 500						OFF
Reject TWD 1000							ON
Accept TWD 1000								OFF
Reserved								ON
Reserved							ON
Disable Bill Reject 4 Times BA Stop By 30 Sec						ON
Enable Bill Reject 4 Times BA Stop By 30 Sec					ON
Stack Banknote when Power-up							ON
Reject Banknote when Power-up								OFF
Reserved								ON
Reserved							ON

XBA-TWD4 (Pulse/MDB/ICT104U/ICT104V) Option Switch Settings

FUNCTION	SW1	SW2	SW3	SW4	SW5	SW6	SW7	SW8
Inhibit Active HIGH	ON
Inhibit Active LOW		OFF
Reserved			ON
Reserved				OFF
Reserved					ON
Reserved						OFF
Reserved							ON
Reserved								OFF
Pulse Mode					MDB Mode	ICT104V Mode
Credit-Pulse Normal HIGH	Scaling Factor (SF)= 100 Decimal Point Position (DPP)= 2				Connect with coin changer		ON
Credit-Pulse Normal LOW	Scaling Factor (SF)= 1 Decimal Point Position (DPP)= 0				Connect with ICT JPSTD converter board		OFF
Pulse Mode					Other Mode	Other Mode
1 pulse / TWD 100					MDB Mode	ICT104V Mode
5 pulse / TWD 100					Reserved	Reserved
10pulse / TWD 100					CT104U Mode	CT104V Mode
25pulse / TWD 100
MDB Mode					OFF	OFF	OFF	OFF
Reserved					OFF	ON	ON	OFF
CT104U Mode					ON	OFF	ON	OFF
CT104V Mode					ON	ON	ON	ON

DIP Switch Location and Access

The DIP switch is located on the CPU board. To access it, remove the CPU board cover first.

The DIP switch is physically located on the side of the XBA unit.

Diagrammatic representation: [Image: A diagram showing the XBA unit with an arrow pointing to the side where the DIP switch is located (labeled (2)). Another diagram shows the CPU board with the DIP switch labeled (1) on it, indicating the need to remove the cover.]

Currency Assign Data

Bill Value	Interface ICT104U	Interface ICT104V	Interface Pulse	Interface MDB
BV1	TWD 100	TWD 100	TWD 100	TWD 100
BV2	TWD 200	TWD 200	TWD 200	TWD 200
BV3	TWD 500	TWD 500	TWD 500	TWD 500
BV4	TWD 1000	TWD 1000	TWD 1000	TWD 1000

Notes

* Manufacture setting
Note 1: Calibration card is needed.

	XBA-NZD5 Bill Acceptor: Option Switch Settings and Currency Assignment Guide Comprehensive guide detailing the XBA-NZD5 bill acceptor's option switch configurations for various modes including Pulse, MDB, and ICT104V. Features currency assignment data for New Zealand Dollars (NZD) and switch location information.
	XBA-USD6 Option Switch Settings and Currency Configuration Guide Detailed guide to XBA-USD6 option switch settings, including pulse, MDB, ICT002U, ICT104U, and ICT104V modes, along with currency assignment data for various bill denominations.
	XBA-HRK9(HRK5+EUR4) Option Switch Settings and Currency Configuration Detailed guide to configuring the XBA-HRK9 bill acceptor, including HRK and EUR currency settings, pulse and MDB interface options, and DIP switch functions for various models like HRK5, EUR4, ICT104U, and ICT104V.
	XBA-JMD6 Bill Acceptor Option Switch Settings and Configuration Guide Detailed guide to configuring the XBA-JMD6 bill acceptor, including option switch settings for various currencies (JMD) and communication protocols (Pulse, MDB, ICT). Covers currency assignment, setup notes, and DIP switch locations.
	XBA-RUB6 Bill Acceptor: Option Switch Settings and Configuration Guide to XBA-RUB6 bill acceptor option switch settings for Pulse, MDB, ICT104U, and ICT104V interfaces, including currency assignment data by International Currency Technologies Corporation.
	XBA-UAH10 Bill Acceptor Option Switch Settings and Configuration Detailed guide for configuring the XBA-UAH10 bill acceptor, including option switch settings for Pulse, MDB, ICT106U, ccNet, and ICT104V modes, along with currency assignment data.
	XBA-KHR8 Bill Acceptor DIP Switch Settings and Configuration Guide Detailed guide to configuring the XBA-KHR8 bill acceptor series from International Currency Technologies Corporation, covering DIP switch settings for Pulse, MDB, ICT002U, ICT104U, and ICT104V interfaces, along with currency assignment data.
	XBA-REN11 Bill Acceptor Switch Settings and Configuration Guide A comprehensive guide detailing the dip switch settings for the XBA-REN11 bill acceptor, covering various protocols like Pulse, MDB, ICT104U, and ICT104V, along with currency assignment data.