Manuals+

XBA-KZT6 Bill Acceptor Option Switch Settings

Supported Bill Types: KZT 200, 500, 1000, 2000, 5000, 10000 (6 bills)

XBA Option Switch Settings (Pulse/MDB/ICT104U/ICT104V)

FUNCTIONSW1SW2SW3SW4SW5SW6SW7SW8
Reject KZT 200ON
Accept KZT 200OFF
Reject KZT 500 & 1000ON
Accept KZT 500 & 1000OFF
Reject KZT 2000ON
Accept KZT 2000OFF
Reject KZT 5000ON
Accept KZT 5000OFF
Reject KZT 10000ON
Accept KZT 10000OFF
Disable Bill Reject 4 Times BA Stop By 30 SecON
Enable Bill Reject 4 Times BA Stop By 30 SecOFF
Stack Banknote when Power-upON
Reject Banknote when Power-upON
ReservedOFF
ReservedOFF

This dip switch is located at the side of XBA.

Diagram: A side view of the XBA unit is shown. A circular callout labeled (2) highlights the DIP Switch located on the side of the unit.

Currency Assign Data

Bill valueInterfaceICT104UICT104VPulseMDB
BV1 KZT 200KZT 200KZT 200KZT 200KZT 200KZT 200
BV2 KZT 500KZT 500KZT 500KZT 500KZT 500KZT 500
BV3 KZT 1000KZT 1000KZT 1000KZT 1000KZT 1000KZT 1000
BV4 KZT 2000KZT 2000KZT 2000KZT 2000KZT 2000KZT 2000
BV5 KZT 5000KZT 5000KZT 5000KZT 5000KZT 5000KZT 5000
BV6 KZT 10000KZT 10000KZT 10000KZT 10000KZT 10000KZT 10000

XBA-KZT6 (Pulse/MDB/ICT104U/ICT104V) Option Switch Settings

FUNCTIONSW1SW2SW3SW4SW5SW6SW7SW8
Inhibit Active HIGHON
Inhibit Active LOWOFF
ReservedON
ReservedOFF
ReservedON
ReservedOFF
ReservedON
ReservedOFF
Pulse ModeMDB ModeICT104V Mode
Credit-Pulse Normal HIGHScaling Factor (SF) = 0.01
Decimal Point Position (DPP) = 0		Connect with coin changer ONConnect with ICT JPSTD converter board ON
Credit-Pulse Normal LOWScaling Factor (SF) = 1
Decimal Point Position (DPP) = 0		Connect with coin changer OFFConnect with ICT JPSTD converter board OFF
Pulse ModeOther ModeON
Pulse ModeOther ModeOFF
1 pulse / KZT 100MDB ModeOFFOFF
2 pulses / KZT 100ReservedOFFON
5 pulses / KZT 100ICT104U ModeONOFF
20 pulses / KZT 100ICT104V ModeONON

This dip switch is located on the CPU board, remove the CPU board cover first.

Diagram: An illustration shows the process: first, the CPU board cover is removed. Then, a close-up view of the DIP Switch, labeled (1), is presented.

Manufacturer Settings

* After setting dip switch of the credit pulses, you should reset the bill acceptor again.

Note:

PDF preview unavailable. Download the PDF instead.

XBA-KZT6(Pulse+MDB EU+ICT104U+ICT104V) Corel PDF Engine Version 17.1.0.572 CorelDRAW X7

Related Documents

Preview XBA-USD6 Option Switch Settings and Currency Configuration Guide
Detailed guide to XBA-USD6 option switch settings, including pulse, MDB, ICT002U, ICT104U, and ICT104V modes, along with currency assignment data for various bill denominations.
Preview XBA-TEY12 Bill Acceptor Option Switch Settings and Configuration
Detailed guide to option switch settings for the International Currency Technologies (ICT) XBA-TEY12 bill acceptor, covering TRY and EUR currencies, Pulse, MDB, and ICT104U/ICT104V modes. Includes currency assignment data and setup notes.
Preview XBA-TWD4 Bill Acceptor Option Switch Settings and Configuration Guide
Comprehensive guide detailing the XBA-TWD4 bill acceptor's DIP switch settings for various operating modes including Pulse, MDB, ICT104U, and ICT104V. Includes currency assignment data and configuration notes.
Preview XBA-RUB6 Bill Acceptor: Option Switch Settings and Configuration
Guide to XBA-RUB6 bill acceptor option switch settings for Pulse, MDB, ICT104U, and ICT104V interfaces, including currency assignment data by International Currency Technologies Corporation.
Preview XBA-NZD5 Bill Acceptor: Option Switch Settings and Currency Assignment Guide
Comprehensive guide detailing the XBA-NZD5 bill acceptor's option switch configurations for various modes including Pulse, MDB, and ICT104V. Features currency assignment data for New Zealand Dollars (NZD) and switch location information.
Preview XBA-KHR8 Bill Acceptor DIP Switch Settings and Configuration Guide
Detailed guide to configuring the XBA-KHR8 bill acceptor series from International Currency Technologies Corporation, covering DIP switch settings for Pulse, MDB, ICT002U, ICT104U, and ICT104V interfaces, along with currency assignment data.
Preview XBA-GEL6 Bill Acceptor: Option Switch Settings and Configuration Guide
Comprehensive guide to configuring the XBA-GEL6 bill acceptor, detailing option switch settings for Pulse, MDB, ICT104U, and ICT104V protocols, supported Lari currency denominations, and currency assignment data.
Preview XBA-SAR4 Bill Acceptor Option Switch Settings and Configuration
Detailed guide to the XBA-SAR4 bill acceptor's option switch settings, covering pulse, MDB, ICT104U, and ICT104V protocols, along with currency assignment data.